Model 200
JOB:
Item No.:
■ Model
200
FOOD WASTE DISPOSER 2 HP – 1 Phase & 3 Phase CORROSION RESISTANT BODY Permanent molded from heat treated aluminum alloy.
TEFLON LIP WATER SEAL Protects the motor from damage by water.
TAPERED ROLLER BEARING Provides longer motor life, quiet operation and shock absorbing.
WATER COOLED MOTOR Provides maximum efficiency and longer life.
QUIET OPERATION Extra thick rubber mounting adaptor and drain outlet isolates sound and eliminates vibration.
Cone Assembly TABLE CUT-OUT: 12” CONE - 12 7/8” 15” CONE - 15 7/8” 18” CONE - 18 7/8”
ALL PIPING 1/2" OPTIONAL CONE COVER
VACUUM BREAKER
SOLENOID VALVE W/ WATER FLOW CONTROL
1 2
/ " FIXED NOZZLE
NEMA 4 Watertight Controls SCRAP RING
DISPOSER CONTROL
FOOD WASTE DISPOSER
2" DRAIN
MSS
MRSS
NOTE: INSTALL PER ALL APPLICABLE CODES
FULL LOAD AMPS
ARSS-2
ARSS
Optional Line Disconnect (LD) available on MSS, MRSS, & ARSS
■ ■ ■ ■ ■ ■
115 Volts
1 Phase
24 Amps
208 Volts
1 Phase
12.1 Amps
230 Volts
1 Phase
12.0 Amps
208 Volts
3 Phase
6.6 Amps
230 Volts
3 Phase
6.0 Amps
460 Volts
3 Phase
3.0 Amps
◆ SPECIFY EXACT OPERATING VOLTAGE ◆
Salvajor Model 200 Food Waste Disposer 2 HP – 1 Phase & 3 Phase D
E
T
A
I
L
S
A
N
D
D
I
M
and rubber drain outlet isolates sound and eliminates vibration. No metal to metal contact.
EXTERIOR HOUSING – Permanent molded from heat treated, corrosion resistant aluminum alloy then computer machined to a smooth polished finish. Paint free.
SHREDDER – 8 inch diameter, machined high strength,
N
S
I
O
N
S
18" CONE
15" CONE
/2" FIXED NOZZLE
20 7/8" (53.02)
177/8" (45.40) 15" (38.10)
55/8" (14.29)
61/2" (16.51)
1 /2" NPT WATER INLET 1 8 /2" (21.59)
13" (33.02)
SPECIFICATIONS: MOUNTING – Rubber adaptor above grind chamber
E
1
2 1 7/16" (54.45)
wear resistant hardened carbide alloy.
18" (45.72)
81/2" (21.59)
2" DRAIN
ROTOR – 8 inch diameter with 4 cutter bars, machined high strength, wear resistant hardened carbide alloy.
11/16" (2.70)
61/2" (16.51)
141/8" (35.92)
55/8" (14.29)
55/8" (14.29)
12" CONE POWER ENTRANCE
147/8" (37.78) 12" (30.48)
RESET BUTTON
61/2" (16.51)
55/8" (14.29)
MOTOR – 2 HP totally enclosed. Water cooled for efficiency and longer life. Built-in manual reset thermal overload protection. Available in 208 volts or 115/ 230 volts, 60 cycle, 1 phase and 208-230/460 volts, 60 cycle, 3 phase.
31/2" SINK MOUNT 31/2" (8.89) SINK OPENING
BEARINGS – Tapered roller (top)
61/2" SINK MOUNT 65/8" (16.83) CUTOUT
3
/4" (1.91)
Sealed ball (bottom) 1 /2" NPT WATER INLET 81/2" (21.59)
SEAL – Teflon Lip Water Seal. WATER REQUIREMENT – 5 gallons of cold water per minute.
15 13/16" (40.16)
2" DRAIN
13" (33.02)
81/2" (21.59)
55/8" (14.29) 91/4" (23.50)
ADJUSTABLE LEG (OPTIONAL)
POWER ENTRANCE
WASTE OUTLET – Rubber drain accepts 2” piping. 11/16" (2.70)
DUAL DIRECTION GRINDING – Designed to operate in either direction. Direction of rotation can be controlled when installed with automatic reversing controls. Reversing rotation can double cutting teeth life. LEG SUPPORT (Optional) – Single leg, adjustable. ASSEMBLIES: (See Specification Sheet) CA – Cone Assembly with 12”, 15” or 18” Cone SA – Sink Assembly with 3 1⁄2” or 6 1⁄2” Sink Collar
NOTE: Dimensions in parenthesis are in centimeters (Specifications subject to change without notice) Current specification details may be found online at www.salvajor.com
SAMPLE SPECIFICATION 200- CA-18
DISPOSER CONTROLS: (See Specification Sheet) MSS: (Non Reversing) MRSS: (Manual Reversing) ARSS-2: (Automatic Reversing) ARSS: (Automatic Reversing)
10 9/16"(26.78) to 14 3/16"(35.99)
RESET BUTTON
Model
Cone Size Assembly
ARSS Disposer Control
( 230/60/3 ) Electrical Specs.
◆ SPECIFY EXACT OPERATING VOLTAGE ◆
The Salvajor Company 1- 800 - SALVAJOR www.salvajor.com
4530 East 75th Terrace Kansas City, Missouri 64132-2081, USA (816) 363 - 1030 FAX: 1 - 800 - 832 - 9373 Email: [email protected] [email protected]
Manufacturers of Commercial Food Waste Disposing Systems since 1944
Printed in USA Form No.S200-9-BH
Item No.:
■ Model
200
FOOD WASTE DISPOSER 2 HP – 1 Phase & 3 Phase CORROSION RESISTANT BODY Permanent molded from heat treated aluminum alloy.
TEFLON LIP WATER SEAL Protects the motor from damage by water.
TAPERED ROLLER BEARING Provides longer motor life, quiet operation and shock absorbing.
WATER COOLED MOTOR Provides maximum efficiency and longer life.
QUIET OPERATION Extra thick rubber mounting adaptor and drain outlet isolates sound and eliminates vibration.
Cone Assembly TABLE CUT-OUT: 12” CONE - 12 7/8” 15” CONE - 15 7/8” 18” CONE - 18 7/8”
ALL PIPING 1/2" OPTIONAL CONE COVER
VACUUM BREAKER
SOLENOID VALVE W/ WATER FLOW CONTROL
1 2
/ " FIXED NOZZLE
NEMA 4 Watertight Controls SCRAP RING
DISPOSER CONTROL
FOOD WASTE DISPOSER
2" DRAIN
MSS
MRSS
NOTE: INSTALL PER ALL APPLICABLE CODES
FULL LOAD AMPS
ARSS-2
ARSS
Optional Line Disconnect (LD) available on MSS, MRSS, & ARSS
■ ■ ■ ■ ■ ■
115 Volts
1 Phase
24 Amps
208 Volts
1 Phase
12.1 Amps
230 Volts
1 Phase
12.0 Amps
208 Volts
3 Phase
6.6 Amps
230 Volts
3 Phase
6.0 Amps
460 Volts
3 Phase
3.0 Amps
◆ SPECIFY EXACT OPERATING VOLTAGE ◆
Salvajor Model 200 Food Waste Disposer 2 HP – 1 Phase & 3 Phase D
E
T
A
I
L
S
A
N
D
D
I
M
and rubber drain outlet isolates sound and eliminates vibration. No metal to metal contact.
EXTERIOR HOUSING – Permanent molded from heat treated, corrosion resistant aluminum alloy then computer machined to a smooth polished finish. Paint free.
SHREDDER – 8 inch diameter, machined high strength,
N
S
I
O
N
S
18" CONE
15" CONE
/2" FIXED NOZZLE
20 7/8" (53.02)
177/8" (45.40) 15" (38.10)
55/8" (14.29)
61/2" (16.51)
1 /2" NPT WATER INLET 1 8 /2" (21.59)
13" (33.02)
SPECIFICATIONS: MOUNTING – Rubber adaptor above grind chamber
E
1
2 1 7/16" (54.45)
wear resistant hardened carbide alloy.
18" (45.72)
81/2" (21.59)
2" DRAIN
ROTOR – 8 inch diameter with 4 cutter bars, machined high strength, wear resistant hardened carbide alloy.
11/16" (2.70)
61/2" (16.51)
141/8" (35.92)
55/8" (14.29)
55/8" (14.29)
12" CONE POWER ENTRANCE
147/8" (37.78) 12" (30.48)
RESET BUTTON
61/2" (16.51)
55/8" (14.29)
MOTOR – 2 HP totally enclosed. Water cooled for efficiency and longer life. Built-in manual reset thermal overload protection. Available in 208 volts or 115/ 230 volts, 60 cycle, 1 phase and 208-230/460 volts, 60 cycle, 3 phase.
31/2" SINK MOUNT 31/2" (8.89) SINK OPENING
BEARINGS – Tapered roller (top)
61/2" SINK MOUNT 65/8" (16.83) CUTOUT
3
/4" (1.91)
Sealed ball (bottom) 1 /2" NPT WATER INLET 81/2" (21.59)
SEAL – Teflon Lip Water Seal. WATER REQUIREMENT – 5 gallons of cold water per minute.
15 13/16" (40.16)
2" DRAIN
13" (33.02)
81/2" (21.59)
55/8" (14.29) 91/4" (23.50)
ADJUSTABLE LEG (OPTIONAL)
POWER ENTRANCE
WASTE OUTLET – Rubber drain accepts 2” piping. 11/16" (2.70)
DUAL DIRECTION GRINDING – Designed to operate in either direction. Direction of rotation can be controlled when installed with automatic reversing controls. Reversing rotation can double cutting teeth life. LEG SUPPORT (Optional) – Single leg, adjustable. ASSEMBLIES: (See Specification Sheet) CA – Cone Assembly with 12”, 15” or 18” Cone SA – Sink Assembly with 3 1⁄2” or 6 1⁄2” Sink Collar
NOTE: Dimensions in parenthesis are in centimeters (Specifications subject to change without notice) Current specification details may be found online at www.salvajor.com
SAMPLE SPECIFICATION 200- CA-18
DISPOSER CONTROLS: (See Specification Sheet) MSS: (Non Reversing) MRSS: (Manual Reversing) ARSS-2: (Automatic Reversing) ARSS: (Automatic Reversing)
10 9/16"(26.78) to 14 3/16"(35.99)
RESET BUTTON
Model
Cone Size Assembly
ARSS Disposer Control
( 230/60/3 ) Electrical Specs.
◆ SPECIFY EXACT OPERATING VOLTAGE ◆
The Salvajor Company 1- 800 - SALVAJOR www.salvajor.com
4530 East 75th Terrace Kansas City, Missouri 64132-2081, USA (816) 363 - 1030 FAX: 1 - 800 - 832 - 9373 Email: [email protected] [email protected]
Manufacturers of Commercial Food Waste Disposing Systems since 1944
Printed in USA Form No.S200-9-BH
