Olympus Pen E-PL7 LCD Screen Replacement
Olympus Pen E-PL7 LCD Screen Replacement
Olympus Pen E-PL7 LCD Screen Replacement This guide will show you how to remove the LCD from the Olympus Pen E-PL7
Written By: Kelsea Weber
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 8
Olympus Pen E-PL7 LCD Screen Replacement
INTRODUCTION Is your LCD Screen cracked or unresponsive? Use this guide to replace it and get back to taking awesome photos. We highly suggest you use a magnetic project mat or an organization tray. This camera has many different types of screws and keeping them organized is key to proper reassembly.
TOOLS: Tweezers (1) Phillips #00 Screwdriver (1) Magnetic Project Mat (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 8
Olympus Pen E-PL7 LCD Screen Replacement
Step 1 — Battery
Turn the camera upside down.
Push the grey tab to the right to open the battery compartment.
Pull out the battery.
The battery is not shown in these photos. Step 2 — LCD Screen
© iFixit — CC BY-NC-SA
www.iFixit.com
Use a Phillips #00 screwdriver to remove the three 2.3 mm screws from the base of the LCD screen.
Page 3 of 8
Olympus Pen E-PL7 LCD Screen Replacement
Step 3
Fully extend the LCD assembly.
Step 4
Remove the two 2.2 mm Phillips screws located on the back of the LCD screen.
Use tweezers to remove the top LCD bracket.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 8
Olympus Pen E-PL7 LCD Screen Replacement
Step 5
Use a Phillips #00 screwdriver to remove the four 1.4 mm screws from the back of the LCD screen.
Remove the LCD ribbon cable with a pair of tweezers.
The cover may fall off after the screws have been removed. Step 6
Carefully lift the LCD screen up and away from the assembly.
Do not attempt to fully remove the screen, as it is attached to the assembly by a ribbon cable.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 8
Olympus Pen E-PL7 LCD Screen Replacement
Step 7
Use tweezers to peel back the plastic cover.
Step 8
Use a spudger to flip back the black bar on the LCD Ribbon ZIF connector.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 8
Olympus Pen E-PL7 LCD Screen Replacement
Step 9
Gently pull the ribbon cable out with tweezers.
Step 10
Remove the LCD Screen.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-22 09:54:31 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 8
Olympus Pen E-PL7 LCD Screen Replacement
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 8 of 8
Olympus Pen E-PL7 LCD Screen Replacement This guide will show you how to remove the LCD from the Olympus Pen E-PL7
Written By: Kelsea Weber
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 8
Olympus Pen E-PL7 LCD Screen Replacement
INTRODUCTION Is your LCD Screen cracked or unresponsive? Use this guide to replace it and get back to taking awesome photos. We highly suggest you use a magnetic project mat or an organization tray. This camera has many different types of screws and keeping them organized is key to proper reassembly.
TOOLS: Tweezers (1) Phillips #00 Screwdriver (1) Magnetic Project Mat (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 8
Olympus Pen E-PL7 LCD Screen Replacement
Step 1 — Battery
Turn the camera upside down.
Push the grey tab to the right to open the battery compartment.
Pull out the battery.
The battery is not shown in these photos. Step 2 — LCD Screen
© iFixit — CC BY-NC-SA
www.iFixit.com
Use a Phillips #00 screwdriver to remove the three 2.3 mm screws from the base of the LCD screen.
Page 3 of 8
Olympus Pen E-PL7 LCD Screen Replacement
Step 3
Fully extend the LCD assembly.
Step 4
Remove the two 2.2 mm Phillips screws located on the back of the LCD screen.
Use tweezers to remove the top LCD bracket.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 8
Olympus Pen E-PL7 LCD Screen Replacement
Step 5
Use a Phillips #00 screwdriver to remove the four 1.4 mm screws from the back of the LCD screen.
Remove the LCD ribbon cable with a pair of tweezers.
The cover may fall off after the screws have been removed. Step 6
Carefully lift the LCD screen up and away from the assembly.
Do not attempt to fully remove the screen, as it is attached to the assembly by a ribbon cable.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 8
Olympus Pen E-PL7 LCD Screen Replacement
Step 7
Use tweezers to peel back the plastic cover.
Step 8
Use a spudger to flip back the black bar on the LCD Ribbon ZIF connector.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 8
Olympus Pen E-PL7 LCD Screen Replacement
Step 9
Gently pull the ribbon cable out with tweezers.
Step 10
Remove the LCD Screen.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-22 09:54:31 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 8
Olympus Pen E-PL7 LCD Screen Replacement
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 8 of 8
