Pipe Covering Protection Saddle
PIPE ROLLS & SADDLES
Pipe Covering Protection Saddle For Nominal Thickness of Covering Shown
q Fig. 160: 1" q Fig. 163: 21⁄2" q Fig. 165A: 4" (Alloy)
q Fig. 161: 11⁄2" q Fig. 162: 2" q Fig. 164: 3" q Fig. 165: 4" q Fig. 166A: 51⁄2" (Alloy)
Size Range:3⁄4" through 36" Material: • Figs. 160, 161, 162, 163, 164, and 165 are curved carbon steel plate. • Figs. 165A and 166A are alloy steel manufactured from ASTM A 387 Grade 22 Chrome Molybdenum steel plate. • Figs. 165A and 166A have a welded-in center plate in all sizes. • All other saddles have a welded-in center plate for pipe sizes 12" and larger. • All saddles are 12" long with side edges turned up. Finish:Plain Service:Designed for use on insulated high temperature systems where heat losses are to be kept to a minimum and to protect insulation against damage. Maximum Temperature:650° F carbon steel, 950° F alloy steel. Approvals:Complies with Federal Specification A-A-1192A (Type 39A & 39B), WW-H-171-E (Type 40A & 40B), ANSI/MSS SP-69 and MSS SP-58 (Type 39A & 39B). Features:Permits finished, weather tight covering at all points of pipe support. Ordering:Specify pipe size, figure number and name. Data for 42" size available on request. Installation:It is recommended that saddle be welded to the pipe.
CL
CL
C
D
C
E
Continued on Following Page.
PROJECT INFORMATION
APPROVAL STAMP
Contractor:
q Approved q Approved as noted q Not approved
Engineer:
Remarks:
Project: Address:
Submittal Date: Notes 1: Notes 2: PH-11.11
PIPE ROLLS & SADDLES
Fig. 160 to Fig 166A
Pipe Covering Protection Saddle (cont.)
FIG. 160, 161, 162, 163, 164, 165, 165A, 166A: DIMENSIONS (IN) • LOADS (LBS) • WEIGHT (LBS) Size of Pipe Roll Pipe Size
3
⁄4
1
11⁄4
1
1 ⁄2
2
21⁄2
3
31⁄2
4
Fig. No. 160• 161• 162• 160• 161• 162• 160 161• 162• 163• 160 161• 162• 163• 160 161• 162• 163• 164• 160 161 162 163 164 160 161 162 163 164 160 161 162 163 164 160 161 162 163 164 165 165A 166A
Max Load n
1,200
1,200
1,200
1,200
1,200
1,200
1,200
1,200
1,200
7,200
Weight
1.4 2.1 2.8 1.4 2.1 2.8 1.4 2.1 2.8 3.6 1.5 2.1 3.2 3.6 1.7 2.3 3.2 3.6 4.5 1.7 2.8 3.2 4.1 4.5 1.9 2.8 3.6 4.1 4.9 2.3 3.2 3.6 4.5 4.9 2.3 3.2 3.6 4.5 4.9 6.1 11.6 15.7
Figs. 171, 175, 177
Figs. 174, 181
2 3 4 21⁄2 3 4 21⁄2 31⁄2 4 5 3 31⁄2 5 6 31⁄2 4 5 6 8 31⁄2 5 6
21⁄2 31⁄2 5 3 4 5 3
8 4 5 6 8 5 6
5 6 31⁄2 5 6 8 4 5 6 8
Figs. 271, 274, 277
2-31⁄2
2-31⁄2
2-31⁄2 4-6 2-31⁄2 4-6 2-31⁄2 4-6
5 6
2-31⁄2
8
4-6
10 5 6
2-31⁄2
8 10 6 8
4-6 8-10 4-6
8 10 5 6
10
8-10
6 8
4-6
8 10 10 14
12 16
8-10 12-14
Center Line of Pipe to Outside of Saddle C
Center Line of Pipe to Center Line of Roll D
E
Figs. 171, 175, 177
Fig. 181
Figs. 271, 274, 277
15⁄8 23⁄16 211⁄16 113⁄16 25⁄16 27⁄8 115⁄16 29⁄16 3 33⁄4 21⁄8 25⁄8 35⁄16 37⁄8 23⁄8 27⁄8 39⁄16 41⁄16 49⁄16 211⁄16 35⁄16 37⁄8 41⁄4 47⁄8 215⁄16 35⁄8 41⁄8 411⁄16 51⁄16 35⁄16 311⁄16 45⁄16 411⁄16 53⁄8 39⁄16 41⁄16 49⁄16 5 55⁄8
21⁄16 23⁄4 35⁄16 25⁄16 27⁄8 31⁄2 21⁄2 31⁄16 35⁄8 43⁄8 25⁄8 31⁄4 4 41⁄2 3 31⁄2 41⁄4 43⁄4 53⁄8 31⁄4 4 41⁄2 51⁄8 55⁄8 31⁄2 45⁄16 413⁄16 57⁄16 6 4 49⁄16 51⁄8 55⁄8 65⁄16 41⁄4 47⁄8 53⁄8 515⁄16 69⁄16
21⁄8 23⁄4 35⁄16 21⁄4 27⁄8 31⁄2 27⁄16 31⁄16 35⁄8 43⁄8 25⁄8 31⁄4 4 45⁄8 215⁄16 31⁄2 41⁄4 413⁄16 53⁄8 31⁄4 4 45⁄8 51⁄8 53⁄4 31⁄2 45⁄16 413⁄16 57⁄16 6 4 49⁄16 51⁄8 55⁄8 65⁄16 41⁄4 47⁄8 53⁄8 515⁄16 69⁄16
21⁄4 27⁄8 33⁄8 27⁄16 3 31⁄2 29⁄16 33⁄16 311⁄16 43⁄8 211⁄16 35⁄16 37⁄8 41⁄2 31⁄16 39⁄16 43⁄16 43⁄4 51⁄4 35⁄16 315⁄16 41⁄2 5 51⁄2 39⁄16 41⁄4 411⁄16 55⁄16 61⁄16 315⁄16 41⁄2 5 511⁄16 63⁄8 43⁄16 43⁄4 51⁄4 6 65⁄8
61⁄2
75⁄8
75⁄8
79⁄16
81⁄8
95⁄8
91⁄2
95⁄16
Maximum recommended loads are applicable only when saddle is used on a flat bearing surface or roller hangers and tack welded to pipe. When saddle is used with a pipe roll, the maximum load for the assembly is the smaller of the two loads. • Saddles may require notching when used with a U-bolt.
n
Continued on Following Page.
PH-1.18
PIPE ROLLS & SADDLES
Fig. 160 to Fig 166A
Pipe Covering Protection Saddle (cont.)
FIG. 160, 161, 162, 163, 164, 165, 165A, 166A: DIMENSIONS (IN) • LOADS (LBS) • WEIGHT (LBS) Size of Pipe Roll Pipe Size
5
6
8
10
12
14
Fig. No. 160 161 162 163 164 165 165A 166A 160 161 162 163 164 165 165A 166A 161 162 163 164 165 165A 166A 161 162 163 164 165 165A 166A 161 162 163 164 165 165A 166A 161 162 163 164 165 165A 166A
Max Load n
1,200
7,200
1,800
7,200
1,800
7,200
1,800
7,200
5,000
11,140
5,000
11,140
Weight
2.3 3.2 3.6 4.5 4.9 6.1 11.6 15.7 3.8 4.4 5.7 6.5 7.7 10.2 12.9 16.3 5.8 6.3 7.2 7.7 10.2 16.9 22.6 5.8 7.7 8.2 8.8 10.8 18.9 24.3 7.8 9.9 10.5 11.4 14.0 28.0 35.5 7.8 9.9 10.5 11.4 14.0 27.6 35.5
Figs. 171, 175, 177
6
Figs. 174, 181
Figs. 271, 274, 277
8
4-6
8 10 10 12
14
16
18 8
8
10 10 12
8-10
12
12
12-14 4-6 8-10 8-10
14
16
12-14
16
18
16-20
10
12
12 14
14 16
16
18
18 12
20 14
8–10
14
16
12-14
16
18
18
20
20 14
– 16
16
18
18
24
20 – – –
16
18
18
20
20
20 24
– – –
8-10 12-14 16-20
16-20 22-24 12-14
16-20
22-24 12-14 16-20
22-24
Center Line of Pipe to Outside of Saddle C 41⁄8 411⁄16 53⁄16 55⁄8 63⁄16 71⁄8 811⁄16 41⁄2 51⁄16 51⁄2 63⁄16 69⁄16 79⁄16 75⁄8 91⁄8 6 61⁄2 71⁄4 711⁄16 811⁄16 101⁄4 71⁄4 75⁄8 81⁄8 811⁄16 93⁄4 911⁄16 111⁄8 81⁄16 85⁄8 91⁄8 95⁄8 1013⁄16 11 125⁄16 83⁄4 95⁄16 97⁄8 105⁄16 115⁄16 119⁄16 127⁄8
Center Line of Pipe to Center Line of Roll D Figs. 171, 175, 177
413⁄16 51⁄2 6 69⁄16 71⁄8 83⁄16 81⁄8 101⁄16 53⁄8 57⁄8 67⁄16 71⁄8 75⁄8 9 91⁄8 105⁄8 71⁄16 79⁄16 85⁄16 9 101⁄8 101⁄16 117⁄8 85⁄16 91⁄16 99⁄16 101⁄8 111⁄4 115⁄16 1215⁄16 91⁄2 103⁄16 1011⁄16 111⁄8 123⁄8 121⁄2 141⁄4 103⁄16 107⁄8 115⁄16 113⁄4 127⁄8 131⁄16 143⁄4
E Fig. 181
Figs. 271, 274, 277
413⁄16 51⁄2 61⁄16 69⁄16 71⁄4
43⁄4 53⁄8 61⁄8 65⁄8 71⁄4
83⁄8
83⁄16
101⁄16 53⁄8 511⁄16 67⁄16 73⁄16 75⁄8
109⁄16 71⁄16 79⁄16 81⁄2 9
97⁄8 51⁄4 6 61⁄2 71⁄4 75⁄8 83⁄4 813⁄16 107⁄16 71⁄16 79⁄16 85⁄16 83⁄4
101⁄8
97⁄8
1113⁄16 81⁄2 9 99⁄16 101⁄16
115⁄8 85⁄16 813⁄16 95⁄16 10
111⁄4
111⁄8
– 91⁄2 101⁄16 109⁄16 111⁄8 – – – 101⁄8 1013⁄16 113⁄8 113⁄4 – – –
121⁄2 91⁄4 10 101⁄2 11 123⁄16 123⁄8 1311⁄16 101⁄16 1011⁄16 113⁄16 115⁄8 125⁄8 127⁄8 141⁄4
9
Maximum recommended loads are applicable only when saddle is used on a flat bearing surface or roller hangers and tack welded to pipe. When saddle is used with a pipe roll, the maximum load for the assembly is the smaller of the two loads. • Saddles may require notching when used with a U-bolt.
n
Continued on Following Page.
PH-1.18
PIPE ROLLS & SADDLES
Fig. 160 to Fig 166A
Pipe Covering Protection Saddle (cont.)
FIG. 160, 161, 162, 163, 164, 165, 165A, 166A: DIMENSIONS (IN) • LOADS (LBS) • WEIGHT (LBS) Size of Pipe Roll Pipe Size
16
18
20
24
30
36
Fig. No. 161 162 163 164 165 165A 166A 161 162 163 164 165 165A 166A 161 162 163 164 165 165A 166A 161 162 163 164 165 165A 166A 161 162 163 164 165 165A 166A 161 162 163 164 165 165A 166A
Max Load n
5,000 7,200 11,140 5,000 7,200
13,370
7,200
13,370
7,200
13,370
7,200
13,370
7,200
13,370
Weight
8.4 10.4 11.1 13.3 15.3 30.1 40.0 9.1 10.4 12.4 13.3 15.3 40.3 52.1 10.4 11.6 12.4 13.4 22.8 44.8 52.1 12.3 13.4 14.3 20.3 23.1 45.4 52.1 13.3 14.0 20.0 21.4 24.0 47.9 55.6 18.0 18.9 20.2 21.6 24.1 48.3 55.8
Figs. 171, 175, 177
Figs. 174, 181
18
20
20
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
24 30 20
24 30 24
30
30
– – – – – – – – – – – – – – –
Figs. 271, 274, 277
16-20
22-24 26-30 16-20
22-24
26-30 22-24
26-30
26-30
36-42
36-42
Center Line of Pipe to Outside of Saddle C 913⁄16 103⁄16 1013⁄16 111⁄16 123⁄16 127⁄16 1313⁄16 1013⁄16 115⁄16 115⁄8 121⁄4 135⁄16 133⁄4 147⁄8 115⁄8 121⁄4 123⁄4 135⁄16 141⁄8 143⁄8 161⁄8 131⁄2 14 145⁄8 151⁄4 167⁄16 1611⁄16 18 1615⁄16 171⁄2 181⁄16 185⁄8 1911⁄16 1915⁄16 211⁄2 201⁄4 2015⁄16 215⁄16 217⁄8 227⁄8 231⁄8 245⁄8
Center Line of Pipe to Center Line of Roll D
E
Figs. 171, 175, 177
Fig. 181
Figs. 271, 274, 277
111⁄4 113⁄16 125⁄16 127⁄8 141⁄8 145⁄16 165⁄8 125⁄16 127⁄8 139⁄16 143⁄16 151⁄4 1511⁄16 175⁄8 139⁄16 141⁄8 1411⁄16 151⁄4 17 173⁄16 1815⁄16 165⁄16 167⁄8 171⁄2 181⁄16 191⁄4 191⁄2 – – – – – – – – – – – – – – –
111⁄4 113⁄4 – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
111⁄8 119⁄16 123⁄16 127⁄16 135⁄8 137⁄8 155⁄8 123⁄16 1211⁄16 131⁄16 135⁄8 143⁄4 151⁄8 165⁄8 131⁄16 135⁄8 143⁄16 143⁄4 157⁄8 161⁄8 177⁄8 151⁄4 153⁄4 167⁄16 17 183⁄16 187⁄16 193⁄4 187⁄8 193⁄8 1915⁄16 201⁄2 211⁄2 213⁄4 233⁄8 221⁄8 225⁄8 233⁄16 2311⁄16 2411⁄16 25 261⁄2
Maximum recommended loads are applicable only when saddle is used on a flat bearing surface or roller hangers and tack welded to pipe. When saddle is used with a pipe roll, the maximum load for the assembly is the smaller of the two loads. • Saddles may require notching when used with a U-bolt.
n
PH-1.18
Pipe Covering Protection Saddle For Nominal Thickness of Covering Shown
q Fig. 160: 1" q Fig. 163: 21⁄2" q Fig. 165A: 4" (Alloy)
q Fig. 161: 11⁄2" q Fig. 162: 2" q Fig. 164: 3" q Fig. 165: 4" q Fig. 166A: 51⁄2" (Alloy)
Size Range:3⁄4" through 36" Material: • Figs. 160, 161, 162, 163, 164, and 165 are curved carbon steel plate. • Figs. 165A and 166A are alloy steel manufactured from ASTM A 387 Grade 22 Chrome Molybdenum steel plate. • Figs. 165A and 166A have a welded-in center plate in all sizes. • All other saddles have a welded-in center plate for pipe sizes 12" and larger. • All saddles are 12" long with side edges turned up. Finish:Plain Service:Designed for use on insulated high temperature systems where heat losses are to be kept to a minimum and to protect insulation against damage. Maximum Temperature:650° F carbon steel, 950° F alloy steel. Approvals:Complies with Federal Specification A-A-1192A (Type 39A & 39B), WW-H-171-E (Type 40A & 40B), ANSI/MSS SP-69 and MSS SP-58 (Type 39A & 39B). Features:Permits finished, weather tight covering at all points of pipe support. Ordering:Specify pipe size, figure number and name. Data for 42" size available on request. Installation:It is recommended that saddle be welded to the pipe.
CL
CL
C
D
C
E
Continued on Following Page.
PROJECT INFORMATION
APPROVAL STAMP
Contractor:
q Approved q Approved as noted q Not approved
Engineer:
Remarks:
Project: Address:
Submittal Date: Notes 1: Notes 2: PH-11.11
PIPE ROLLS & SADDLES
Fig. 160 to Fig 166A
Pipe Covering Protection Saddle (cont.)
FIG. 160, 161, 162, 163, 164, 165, 165A, 166A: DIMENSIONS (IN) • LOADS (LBS) • WEIGHT (LBS) Size of Pipe Roll Pipe Size
3
⁄4
1
11⁄4
1
1 ⁄2
2
21⁄2
3
31⁄2
4
Fig. No. 160• 161• 162• 160• 161• 162• 160 161• 162• 163• 160 161• 162• 163• 160 161• 162• 163• 164• 160 161 162 163 164 160 161 162 163 164 160 161 162 163 164 160 161 162 163 164 165 165A 166A
Max Load n
1,200
1,200
1,200
1,200
1,200
1,200
1,200
1,200
1,200
7,200
Weight
1.4 2.1 2.8 1.4 2.1 2.8 1.4 2.1 2.8 3.6 1.5 2.1 3.2 3.6 1.7 2.3 3.2 3.6 4.5 1.7 2.8 3.2 4.1 4.5 1.9 2.8 3.6 4.1 4.9 2.3 3.2 3.6 4.5 4.9 2.3 3.2 3.6 4.5 4.9 6.1 11.6 15.7
Figs. 171, 175, 177
Figs. 174, 181
2 3 4 21⁄2 3 4 21⁄2 31⁄2 4 5 3 31⁄2 5 6 31⁄2 4 5 6 8 31⁄2 5 6
21⁄2 31⁄2 5 3 4 5 3
8 4 5 6 8 5 6
5 6 31⁄2 5 6 8 4 5 6 8
Figs. 271, 274, 277
2-31⁄2
2-31⁄2
2-31⁄2 4-6 2-31⁄2 4-6 2-31⁄2 4-6
5 6
2-31⁄2
8
4-6
10 5 6
2-31⁄2
8 10 6 8
4-6 8-10 4-6
8 10 5 6
10
8-10
6 8
4-6
8 10 10 14
12 16
8-10 12-14
Center Line of Pipe to Outside of Saddle C
Center Line of Pipe to Center Line of Roll D
E
Figs. 171, 175, 177
Fig. 181
Figs. 271, 274, 277
15⁄8 23⁄16 211⁄16 113⁄16 25⁄16 27⁄8 115⁄16 29⁄16 3 33⁄4 21⁄8 25⁄8 35⁄16 37⁄8 23⁄8 27⁄8 39⁄16 41⁄16 49⁄16 211⁄16 35⁄16 37⁄8 41⁄4 47⁄8 215⁄16 35⁄8 41⁄8 411⁄16 51⁄16 35⁄16 311⁄16 45⁄16 411⁄16 53⁄8 39⁄16 41⁄16 49⁄16 5 55⁄8
21⁄16 23⁄4 35⁄16 25⁄16 27⁄8 31⁄2 21⁄2 31⁄16 35⁄8 43⁄8 25⁄8 31⁄4 4 41⁄2 3 31⁄2 41⁄4 43⁄4 53⁄8 31⁄4 4 41⁄2 51⁄8 55⁄8 31⁄2 45⁄16 413⁄16 57⁄16 6 4 49⁄16 51⁄8 55⁄8 65⁄16 41⁄4 47⁄8 53⁄8 515⁄16 69⁄16
21⁄8 23⁄4 35⁄16 21⁄4 27⁄8 31⁄2 27⁄16 31⁄16 35⁄8 43⁄8 25⁄8 31⁄4 4 45⁄8 215⁄16 31⁄2 41⁄4 413⁄16 53⁄8 31⁄4 4 45⁄8 51⁄8 53⁄4 31⁄2 45⁄16 413⁄16 57⁄16 6 4 49⁄16 51⁄8 55⁄8 65⁄16 41⁄4 47⁄8 53⁄8 515⁄16 69⁄16
21⁄4 27⁄8 33⁄8 27⁄16 3 31⁄2 29⁄16 33⁄16 311⁄16 43⁄8 211⁄16 35⁄16 37⁄8 41⁄2 31⁄16 39⁄16 43⁄16 43⁄4 51⁄4 35⁄16 315⁄16 41⁄2 5 51⁄2 39⁄16 41⁄4 411⁄16 55⁄16 61⁄16 315⁄16 41⁄2 5 511⁄16 63⁄8 43⁄16 43⁄4 51⁄4 6 65⁄8
61⁄2
75⁄8
75⁄8
79⁄16
81⁄8
95⁄8
91⁄2
95⁄16
Maximum recommended loads are applicable only when saddle is used on a flat bearing surface or roller hangers and tack welded to pipe. When saddle is used with a pipe roll, the maximum load for the assembly is the smaller of the two loads. • Saddles may require notching when used with a U-bolt.
n
Continued on Following Page.
PH-1.18
PIPE ROLLS & SADDLES
Fig. 160 to Fig 166A
Pipe Covering Protection Saddle (cont.)
FIG. 160, 161, 162, 163, 164, 165, 165A, 166A: DIMENSIONS (IN) • LOADS (LBS) • WEIGHT (LBS) Size of Pipe Roll Pipe Size
5
6
8
10
12
14
Fig. No. 160 161 162 163 164 165 165A 166A 160 161 162 163 164 165 165A 166A 161 162 163 164 165 165A 166A 161 162 163 164 165 165A 166A 161 162 163 164 165 165A 166A 161 162 163 164 165 165A 166A
Max Load n
1,200
7,200
1,800
7,200
1,800
7,200
1,800
7,200
5,000
11,140
5,000
11,140
Weight
2.3 3.2 3.6 4.5 4.9 6.1 11.6 15.7 3.8 4.4 5.7 6.5 7.7 10.2 12.9 16.3 5.8 6.3 7.2 7.7 10.2 16.9 22.6 5.8 7.7 8.2 8.8 10.8 18.9 24.3 7.8 9.9 10.5 11.4 14.0 28.0 35.5 7.8 9.9 10.5 11.4 14.0 27.6 35.5
Figs. 171, 175, 177
6
Figs. 174, 181
Figs. 271, 274, 277
8
4-6
8 10 10 12
14
16
18 8
8
10 10 12
8-10
12
12
12-14 4-6 8-10 8-10
14
16
12-14
16
18
16-20
10
12
12 14
14 16
16
18
18 12
20 14
8–10
14
16
12-14
16
18
18
20
20 14
– 16
16
18
18
24
20 – – –
16
18
18
20
20
20 24
– – –
8-10 12-14 16-20
16-20 22-24 12-14
16-20
22-24 12-14 16-20
22-24
Center Line of Pipe to Outside of Saddle C 41⁄8 411⁄16 53⁄16 55⁄8 63⁄16 71⁄8 811⁄16 41⁄2 51⁄16 51⁄2 63⁄16 69⁄16 79⁄16 75⁄8 91⁄8 6 61⁄2 71⁄4 711⁄16 811⁄16 101⁄4 71⁄4 75⁄8 81⁄8 811⁄16 93⁄4 911⁄16 111⁄8 81⁄16 85⁄8 91⁄8 95⁄8 1013⁄16 11 125⁄16 83⁄4 95⁄16 97⁄8 105⁄16 115⁄16 119⁄16 127⁄8
Center Line of Pipe to Center Line of Roll D Figs. 171, 175, 177
413⁄16 51⁄2 6 69⁄16 71⁄8 83⁄16 81⁄8 101⁄16 53⁄8 57⁄8 67⁄16 71⁄8 75⁄8 9 91⁄8 105⁄8 71⁄16 79⁄16 85⁄16 9 101⁄8 101⁄16 117⁄8 85⁄16 91⁄16 99⁄16 101⁄8 111⁄4 115⁄16 1215⁄16 91⁄2 103⁄16 1011⁄16 111⁄8 123⁄8 121⁄2 141⁄4 103⁄16 107⁄8 115⁄16 113⁄4 127⁄8 131⁄16 143⁄4
E Fig. 181
Figs. 271, 274, 277
413⁄16 51⁄2 61⁄16 69⁄16 71⁄4
43⁄4 53⁄8 61⁄8 65⁄8 71⁄4
83⁄8
83⁄16
101⁄16 53⁄8 511⁄16 67⁄16 73⁄16 75⁄8
109⁄16 71⁄16 79⁄16 81⁄2 9
97⁄8 51⁄4 6 61⁄2 71⁄4 75⁄8 83⁄4 813⁄16 107⁄16 71⁄16 79⁄16 85⁄16 83⁄4
101⁄8
97⁄8
1113⁄16 81⁄2 9 99⁄16 101⁄16
115⁄8 85⁄16 813⁄16 95⁄16 10
111⁄4
111⁄8
– 91⁄2 101⁄16 109⁄16 111⁄8 – – – 101⁄8 1013⁄16 113⁄8 113⁄4 – – –
121⁄2 91⁄4 10 101⁄2 11 123⁄16 123⁄8 1311⁄16 101⁄16 1011⁄16 113⁄16 115⁄8 125⁄8 127⁄8 141⁄4
9
Maximum recommended loads are applicable only when saddle is used on a flat bearing surface or roller hangers and tack welded to pipe. When saddle is used with a pipe roll, the maximum load for the assembly is the smaller of the two loads. • Saddles may require notching when used with a U-bolt.
n
Continued on Following Page.
PH-1.18
PIPE ROLLS & SADDLES
Fig. 160 to Fig 166A
Pipe Covering Protection Saddle (cont.)
FIG. 160, 161, 162, 163, 164, 165, 165A, 166A: DIMENSIONS (IN) • LOADS (LBS) • WEIGHT (LBS) Size of Pipe Roll Pipe Size
16
18
20
24
30
36
Fig. No. 161 162 163 164 165 165A 166A 161 162 163 164 165 165A 166A 161 162 163 164 165 165A 166A 161 162 163 164 165 165A 166A 161 162 163 164 165 165A 166A 161 162 163 164 165 165A 166A
Max Load n
5,000 7,200 11,140 5,000 7,200
13,370
7,200
13,370
7,200
13,370
7,200
13,370
7,200
13,370
Weight
8.4 10.4 11.1 13.3 15.3 30.1 40.0 9.1 10.4 12.4 13.3 15.3 40.3 52.1 10.4 11.6 12.4 13.4 22.8 44.8 52.1 12.3 13.4 14.3 20.3 23.1 45.4 52.1 13.3 14.0 20.0 21.4 24.0 47.9 55.6 18.0 18.9 20.2 21.6 24.1 48.3 55.8
Figs. 171, 175, 177
Figs. 174, 181
18
20
20
– – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
24 30 20
24 30 24
30
30
– – – – – – – – – – – – – – –
Figs. 271, 274, 277
16-20
22-24 26-30 16-20
22-24
26-30 22-24
26-30
26-30
36-42
36-42
Center Line of Pipe to Outside of Saddle C 913⁄16 103⁄16 1013⁄16 111⁄16 123⁄16 127⁄16 1313⁄16 1013⁄16 115⁄16 115⁄8 121⁄4 135⁄16 133⁄4 147⁄8 115⁄8 121⁄4 123⁄4 135⁄16 141⁄8 143⁄8 161⁄8 131⁄2 14 145⁄8 151⁄4 167⁄16 1611⁄16 18 1615⁄16 171⁄2 181⁄16 185⁄8 1911⁄16 1915⁄16 211⁄2 201⁄4 2015⁄16 215⁄16 217⁄8 227⁄8 231⁄8 245⁄8
Center Line of Pipe to Center Line of Roll D
E
Figs. 171, 175, 177
Fig. 181
Figs. 271, 274, 277
111⁄4 113⁄16 125⁄16 127⁄8 141⁄8 145⁄16 165⁄8 125⁄16 127⁄8 139⁄16 143⁄16 151⁄4 1511⁄16 175⁄8 139⁄16 141⁄8 1411⁄16 151⁄4 17 173⁄16 1815⁄16 165⁄16 167⁄8 171⁄2 181⁄16 191⁄4 191⁄2 – – – – – – – – – – – – – – –
111⁄4 113⁄4 – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – –
111⁄8 119⁄16 123⁄16 127⁄16 135⁄8 137⁄8 155⁄8 123⁄16 1211⁄16 131⁄16 135⁄8 143⁄4 151⁄8 165⁄8 131⁄16 135⁄8 143⁄16 143⁄4 157⁄8 161⁄8 177⁄8 151⁄4 153⁄4 167⁄16 17 183⁄16 187⁄16 193⁄4 187⁄8 193⁄8 1915⁄16 201⁄2 211⁄2 213⁄4 233⁄8 221⁄8 225⁄8 233⁄16 2311⁄16 2411⁄16 25 261⁄2
Maximum recommended loads are applicable only when saddle is used on a flat bearing surface or roller hangers and tack welded to pipe. When saddle is used with a pipe roll, the maximum load for the assembly is the smaller of the two loads. • Saddles may require notching when used with a U-bolt.
n
PH-1.18
