Rack Floor Attachment Kit
Rack Floor Attachment Kit Part Number(s): RFAKIT
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2011
CM484C Required Tools
1/2-13 Hex Nut 1/2" Flat Washer
1/2-13 X 3 3/4" Long Concrete Stud Anchor The Rack Floor Attachment Kit includes the following components: (4) 1/2-13 X 3 3/4" Long Concrete Stud Anchors (4) 1/2" Flat Washers (4) 1/2-13 Hex Nuts • •
Drill with 1/2" Dia. Masonry Bit at least 2 1/2" Long
Hammer
The Rack Floor Attachment Kit may be used to anchor any of Panduit’s 3" Standard Racks, 6" Racks, 4 Post Racks, or Net-SERV and Net-Access Cabinets in place to a concrete floor. The 1/2-13 X 3 3/4" Long Concrete Stud Anchors are not reuseable once they are fastened into the floor, so it is very important that the rack or cabinet is placed in the desired location prior to installation.
Installation Step 1: With rack or cabinet in place, mark areas on the floor where the holes will be drilled. Step 2: Temporarily remove rack or cabinet to drill (4) holes into floor. The (4) holes must be drilled 2 1/2"-2 3/4" deep using a 1/2" dia. masonry drill bit. Step 3: Tap the 1/2-13 X 3 3/4" Long Concrete Stud Anchors into all (4) holes in the orientation shown using a hammer. Realign rack or cabinet over the Anchors. Step 4: Tighten the rack or cabinet to the floor using the (4) 1/2" Flat Washers and the (4) 1/2-13 Hex Nuts.
Step 2
Step 1
Mark on floor holes to be drilled
Drill holes with 1/2" Dia. Masonry Bit at least 2 1/2" Long
Concrete Floor
Step 4
Step 3 Tap in all anchors using hammer
1/2-13 X 3 3/4" Long Concrete Stud Anchor
1/2" Flat Washers and 1/2-13 Hex Nuts
Concrete Floor
FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
CM484C
Net-SERV Cabinet Mounting Footprint Floor Anchoring Footprint
B
4.0” [102mm]
A D
3.2” [82mm]
Cabinet Dimensions Width Depth
C A
Mounting Distances B C
D
23.6" [600mm]
47.2" [1200mm]
23.6" [600mm] 47.2" [1200mm] 40.7" [1035mm]
9.8" [250mm]
27.6" [700mm]
47.2" [1200mm]
27.6" [700mm] 47.2" [1200mm] 40.7" [1035mm] 11.8" [300mm]
Net-Access Cabinet Mounting Footprint (32"X 48" Cabinet Shown) 41" Deep Cabinets- 4 Mounting Hole Locations 48" Deep Cabinets- 6 Mounting Hole Locations
Floor Anchoring Footprint 48.00” [1219.2mm]
19.52” [495.8mm]
31.5” [800.0mm]
33.62” [854.1mm] 41” DEEP CABINETS 41.91” [1064.5mm] 48” DEEP CABINETS
E-mail: [email protected]
For Instructions in Local Languages and Technical Support: www.panduit.com/resources/install_maintain.asp
www.panduit.com
Fax: (708) 444-6448
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2011
CM484C Required Tools
1/2-13 Hex Nut 1/2" Flat Washer
1/2-13 X 3 3/4" Long Concrete Stud Anchor The Rack Floor Attachment Kit includes the following components: (4) 1/2-13 X 3 3/4" Long Concrete Stud Anchors (4) 1/2" Flat Washers (4) 1/2-13 Hex Nuts • •
Drill with 1/2" Dia. Masonry Bit at least 2 1/2" Long
Hammer
The Rack Floor Attachment Kit may be used to anchor any of Panduit’s 3" Standard Racks, 6" Racks, 4 Post Racks, or Net-SERV and Net-Access Cabinets in place to a concrete floor. The 1/2-13 X 3 3/4" Long Concrete Stud Anchors are not reuseable once they are fastened into the floor, so it is very important that the rack or cabinet is placed in the desired location prior to installation.
Installation Step 1: With rack or cabinet in place, mark areas on the floor where the holes will be drilled. Step 2: Temporarily remove rack or cabinet to drill (4) holes into floor. The (4) holes must be drilled 2 1/2"-2 3/4" deep using a 1/2" dia. masonry drill bit. Step 3: Tap the 1/2-13 X 3 3/4" Long Concrete Stud Anchors into all (4) holes in the orientation shown using a hammer. Realign rack or cabinet over the Anchors. Step 4: Tighten the rack or cabinet to the floor using the (4) 1/2" Flat Washers and the (4) 1/2-13 Hex Nuts.
Step 2
Step 1
Mark on floor holes to be drilled
Drill holes with 1/2" Dia. Masonry Bit at least 2 1/2" Long
Concrete Floor
Step 4
Step 3 Tap in all anchors using hammer
1/2-13 X 3 3/4" Long Concrete Stud Anchor
1/2" Flat Washers and 1/2-13 Hex Nuts
Concrete Floor
FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
CM484C
Net-SERV Cabinet Mounting Footprint Floor Anchoring Footprint
B
4.0” [102mm]
A D
3.2” [82mm]
Cabinet Dimensions Width Depth
C A
Mounting Distances B C
D
23.6" [600mm]
47.2" [1200mm]
23.6" [600mm] 47.2" [1200mm] 40.7" [1035mm]
9.8" [250mm]
27.6" [700mm]
47.2" [1200mm]
27.6" [700mm] 47.2" [1200mm] 40.7" [1035mm] 11.8" [300mm]
Net-Access Cabinet Mounting Footprint (32"X 48" Cabinet Shown) 41" Deep Cabinets- 4 Mounting Hole Locations 48" Deep Cabinets- 6 Mounting Hole Locations
Floor Anchoring Footprint 48.00” [1219.2mm]
19.52” [495.8mm]
31.5” [800.0mm]
33.62” [854.1mm] 41” DEEP CABINETS 41.91” [1064.5mm] 48” DEEP CABINETS
E-mail: [email protected]
For Instructions in Local Languages and Technical Support: www.panduit.com/resources/install_maintain.asp
www.panduit.com
Fax: (708) 444-6448
