Replacing a Zipper Pull Tab on your Patagonia Jacket - Amazon Web ...
Replacing a Zipper Pull Tab on your Patagonia Jacket
Replacing a Zipper Pull Tab on your Patagonia Jacket Replace a zipper pull tab.
Written By: Brittany McCrigler
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
Replacing a Zipper Pull Tab on your Patagonia Jacket
INTRODUCTION [video: https://vimeo.com/57614686] Make it easier to zip up your favorite jacket by replacing a missing zipper pull tab. It only takes a few minutes and afterward you’ll be able to grib your zipper pull with mittens or gloves. For replacement parts or further assistance, contact Patagonia Customer Service.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
Replacing a Zipper Pull Tab on your Patagonia Jacket
Step 1 — Zipper Pull Tab
Get your new zipper pull and position it with the pull-tab down.
Lift up the zipper, as if you were pulling the zipper closed.
Step 2
Insert the zipper pull into the smaller hole in the zipper. This is the top hole when the zipper is hanging normally.
Pull the zipper pull through the smaller hole.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 5
Replacing a Zipper Pull Tab on your Patagonia Jacket
Step 3
Rest the zipper back in its normal, hanging position.
Take top end of the zipper pull and insert it into the bigger, lower hole in the zipper.
Step 4
Pull the top of the zipper pull through the hole to create a loop on the backside of the zipper.
Bring the zipper pull-tab through the loop.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 5
Replacing a Zipper Pull Tab on your Patagonia Jacket
Step 5
Pull the zipper pull-tab snug.
The zipper pull should now be inserted and lay flat.
This document was last generated on 2017-08-02 03:50:22 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
Replacing a Zipper Pull Tab on your Patagonia Jacket Replace a zipper pull tab.
Written By: Brittany McCrigler
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
Replacing a Zipper Pull Tab on your Patagonia Jacket
INTRODUCTION [video: https://vimeo.com/57614686] Make it easier to zip up your favorite jacket by replacing a missing zipper pull tab. It only takes a few minutes and afterward you’ll be able to grib your zipper pull with mittens or gloves. For replacement parts or further assistance, contact Patagonia Customer Service.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
Replacing a Zipper Pull Tab on your Patagonia Jacket
Step 1 — Zipper Pull Tab
Get your new zipper pull and position it with the pull-tab down.
Lift up the zipper, as if you were pulling the zipper closed.
Step 2
Insert the zipper pull into the smaller hole in the zipper. This is the top hole when the zipper is hanging normally.
Pull the zipper pull through the smaller hole.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 5
Replacing a Zipper Pull Tab on your Patagonia Jacket
Step 3
Rest the zipper back in its normal, hanging position.
Take top end of the zipper pull and insert it into the bigger, lower hole in the zipper.
Step 4
Pull the top of the zipper pull through the hole to create a loop on the backside of the zipper.
Bring the zipper pull-tab through the loop.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 5
Replacing a Zipper Pull Tab on your Patagonia Jacket
Step 5
Pull the zipper pull-tab snug.
The zipper pull should now be inserted and lay flat.
This document was last generated on 2017-08-02 03:50:22 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
