Royal Heat RS-100 Fuse Replacement
Royal Heat RS-100 Fuse Replacement
Royal Heat RS-100 Fuse Replacement This guide will show you how to replace the fuse.
Written By: Long Tran
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
Royal Heat RS-100 Fuse Replacement
INTRODUCTION Check the fuse when the current flow through the power cord, but not through the heater coil.
TOOLS: Phillips #2 Screwdriver (1) Flathead Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
Royal Heat RS-100 Fuse Replacement
Step 1 — Panel
Unplug the power cord.
Flip the device over so the bottom is facing up.
Remove the two 10mm screws holding the back panel using a Phillips #2 screwdriver.
Step 2
Place the Flathead Screw driver parallel with the gap between the back and the heater body, then twist until the two parts of panel are separated. You may have to do this on four sides of the panel.
Remove the front panel by pulling them apart. The front panel should come out easily.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 5
Royal Heat RS-100 Fuse Replacement
Step 3
Remove the two dial caps from the two switches by lifting them up.
Step 4 — Fuse
Do not pry from the middle of the fuse because some fuses are made of glass.
Pry one end of the fuse from the bracket until it is separated from the holder.
Remove the fuse by lifting it up.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 5
Royal Heat RS-100 Fuse Replacement
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-07-13 07:58:00 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
Royal Heat RS-100 Fuse Replacement This guide will show you how to replace the fuse.
Written By: Long Tran
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
Royal Heat RS-100 Fuse Replacement
INTRODUCTION Check the fuse when the current flow through the power cord, but not through the heater coil.
TOOLS: Phillips #2 Screwdriver (1) Flathead Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
Royal Heat RS-100 Fuse Replacement
Step 1 — Panel
Unplug the power cord.
Flip the device over so the bottom is facing up.
Remove the two 10mm screws holding the back panel using a Phillips #2 screwdriver.
Step 2
Place the Flathead Screw driver parallel with the gap between the back and the heater body, then twist until the two parts of panel are separated. You may have to do this on four sides of the panel.
Remove the front panel by pulling them apart. The front panel should come out easily.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 5
Royal Heat RS-100 Fuse Replacement
Step 3
Remove the two dial caps from the two switches by lifting them up.
Step 4 — Fuse
Do not pry from the middle of the fuse because some fuses are made of glass.
Pry one end of the fuse from the bracket until it is separated from the holder.
Remove the fuse by lifting it up.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 5
Royal Heat RS-100 Fuse Replacement
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-07-13 07:58:00 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
