Schall-Ex® Slide GS-A Fitting Instructions
Schall-Ex® Slide GS-A Fitting Instructions Included:
Tools
1 x Schall-Ex Slide GS-A Sliding door drop seal 1 x Schall-Ex Slide GS-A Aluminium backing strip
1
All dimensions in mm
2
1.1
44.5 Right hand actuation
11
15.4
Left hand actuation
2.1 L
L
1.2 2.2
A (*see cut back)
L 2.3 L Actuating block (not supplied)
1.1 The actuator can be moved based on which side the door closes into the stop. Simply remove the end brackets, pull out the seal from the housing, flip and relocate brackets.
*A = Seal cut back: max. See product label
1.2 Measure length of door (L).
2.1 The seal needs to be the same size as door length (L). Measure the seal from actuator end, making sure to mark the cutting point on the seal and the aluminium backing strip. 2.2 Partially remove the silicone gasket to cut the seal and the aluminium backing strip at door length (L). Please ensure to consider max cut back (A). 2.3 Replace silicone gasket and cut to size with scissors or a stanley knife.
Schall-ex-slide-gs-a/F/1.0.0
Schall-Ex® Slide GS-A Fitting Instructions
3
44 3.1
5 4.1
4.1
3.2
4.2
+
-
3.1 Peel away from back of seal to reveal adhesive strip. Push fit seal into place onto bottom of glass door.
4.1 Seal adjustment may be required so that the seal drops as in 4.2. To adjust the seal, pull the actuator out by hand and twist clockwise to reduce seal travel or anti-clockwise to increase seal travel.
3.2 Peel away from back of aluminium backing strip to reveal adhesive strip. Push fit into place onto the bottom opposite side to the seal.
4.2 Please take the following diagrams into account, the seal should be fully contacting the floor but not over adjusted so that the seal is bowing.
5 Open and close door to test seal drop. Repeat step 4 and test again if further adjustment required.
Schall-ex-slide-gs-a/F/1.0.0
Tools
1 x Schall-Ex Slide GS-A Sliding door drop seal 1 x Schall-Ex Slide GS-A Aluminium backing strip
1
All dimensions in mm
2
1.1
44.5 Right hand actuation
11
15.4
Left hand actuation
2.1 L
L
1.2 2.2
A (*see cut back)
L 2.3 L Actuating block (not supplied)
1.1 The actuator can be moved based on which side the door closes into the stop. Simply remove the end brackets, pull out the seal from the housing, flip and relocate brackets.
*A = Seal cut back: max. See product label
1.2 Measure length of door (L).
2.1 The seal needs to be the same size as door length (L). Measure the seal from actuator end, making sure to mark the cutting point on the seal and the aluminium backing strip. 2.2 Partially remove the silicone gasket to cut the seal and the aluminium backing strip at door length (L). Please ensure to consider max cut back (A). 2.3 Replace silicone gasket and cut to size with scissors or a stanley knife.
Schall-ex-slide-gs-a/F/1.0.0
Schall-Ex® Slide GS-A Fitting Instructions
3
44 3.1
5 4.1
4.1
3.2
4.2
+
-
3.1 Peel away from back of seal to reveal adhesive strip. Push fit seal into place onto bottom of glass door.
4.1 Seal adjustment may be required so that the seal drops as in 4.2. To adjust the seal, pull the actuator out by hand and twist clockwise to reduce seal travel or anti-clockwise to increase seal travel.
3.2 Peel away from back of aluminium backing strip to reveal adhesive strip. Push fit into place onto the bottom opposite side to the seal.
4.2 Please take the following diagrams into account, the seal should be fully contacting the floor but not over adjusted so that the seal is bowing.
5 Open and close door to test seal drop. Repeat step 4 and test again if further adjustment required.
Schall-ex-slide-gs-a/F/1.0.0
