Silversphere Wireless Series
WRCA Emergency Call Pull Station w/ Check-in & Reset WRCA Emergency Call Pull Station w/ Check-in, Reset & Temperature WRTA Emergency Call Touch Pad w/ Check-in & Reset WRTA Emergency Call Touch Pad w/ Check-in, Reset & Temperature WCCA Wireless Call Cord Station WCCA-NC Wireless Bed Pressure Station
2 2 2 2 2 2
Wheel Chair Monitoring Solution
3
WURA Universal Reset Station with Check-in WTUA Emergency Call Touch Pad w/ Check-in, Reset & N.O. Dry Contact WCUA Emergency Call Pull Station w/ Check-in, Reset & N.O. Dry Contact
4 4 4
WMCA Emergency Call Pull Station w/ Check-in, Reset & Built-in Motion Sensor WMTA Emergency Call Touch Pad w/ Check-in, Reset & Built-in Motion Sensor
5 5
Pendants 6 Universal Transmitters (Introduction to WUTA & WUTB-RS) 6 WDBA Door Bell Transmitter 6 WUTA Universal Transmitter
7
WUTB-RS Universal Transmitter w/ Onboard Reed Switch
8
Summary of device part numbers 9 Batteries 9 Silversphere Wireless Series
© 2014 Silversphere - Doc.Wireless Series 0214
Companion One Silversphere Wireless Transmitters Silversphere RF transmitters allow for wireless activation of an emergency call from anywhere within a resident’s apartment or common area. These transmitters can be used in a fully wireless system or as an added feature on a hardwired system.
The WRCA-T version of the pull cord also records and reports room temperature.* The WCCA wireless call cord uses a push button to trigger an alarm. A second alarm sounds if the pull cord is pulled out of the faceplate. (WCCA and WCCA-3 are flush mount stations. Single- and triple-gang surfacemount junction box not provided.)
The WRTA wireless touch pad is surface mounted to a wall. Pushing anywhere on the face of this panel activates an emergency call. This transmitter is useful in places where a fixed location to call for help is desired, but where a pull cord is not required. The WRTA is a dual-purpose touch pad that can be reset at the station and also be used for wireless resident check-in when applicable. The WRTA-T version of the touch pad also records and reports room temperature.* The WRCA wireless pull cord functions similarly to the WRTA except that the device is activated by pulling the pull cord, rather than touching the faceplate. This transmitter is useful in areas like bathrooms and bedrooms where a pull cord reaching to the floor is desired. The WRCA is a dual-purpose pull cord that can be reset at the station and also be used for wireless resident check-in when applicable.
*
Temperature reporting requires Auditrak and HWNA.
Silversphere Wireless Series
© 2014 Silversphere - Doc.Wireless Series 0214
See Bedside Monitoring Sheet for more information on bedside monitoring options.
Companion One (Rear) Mounting Clip
Fall-risk residents want to retain their sense of mobility, dignity and independence, but you want to make sure they're monitored and protected at all times. How do you balance the two priorities? Silversphere offers seat and wheelchair wireless monitoring. This versatile feature will allow you to discreetly monitor fall-risk residents and will alert the caregiver when a fall-risk resident attempts to get up, prompting immediate assistance.
CCSA-WC10-W-Kit
CCSA-WC10- W
The CCSA-WC10-W-Kit includes one pressure pad, a connection cable, and a pre-assembled wheelchair monitor, wiremold box, and metal clip assembly. Simply attach the assembly to the chair and plug the cable and pad into the connection in front. When a resident gets out of the chair or when the cable is disconnected from the monitor, a notification is sent to your Companion One system and any subsequent notification devices, such as pagers, radios, or handsets.
Includes the following: 10"x 15" Wheelchair Pad (CCSA-WC10-W) Normally-Closed Wireless Monitor (WCCA-NC) 36" cable (325001) Wiremold Device Box with Mounting Clip Replacement Wheelchair Pad 10" x 15" w/ 4pin connection
Silversphere Wireless Series
© 2014 Silversphere - Doc.Wireless Series 0214
Companion One The WURA universal reset station provides a simple reset or check button capable of resetting any fixed station or other Silversphere universal transmitter. Use it also for Staff Check to record care staff compliance, or in door monitoring solutions as a door alarm reset option. The WTUA and the WCUA both provide an inexpensive solution to pre-existing hardwired systems when upgrading to wireless. Both come equipped with a normally open dry contact, most commonly used in connecting a smoke detector. This dry contact may be programmed to create a different alarm event than pulling the pull cord, thus allowing installers to use pre-existing wiring to connect a smoke detector, eliminating the need for a separate transmitter for the smoke detector.
From left to right: WCUA, WTUA, WURA
WTUA/WCUA installation
PUS H AND HOL D
T O T E S T WE E KL Y
1) Connect house wiring from smoke detector to the dry contacts located on the back of each WCUA/WTUA.
Silversphere Wireless Series
Note: There should be no voltage on the line.
© 2014 Silversphere - Doc.Wireless Series 0214
Companion One
The WMCA is a wireless pull cord station and motion sensor in one. The pull cord and reset button function identically to the WRCA.
The motion sensor may be programmed to generate a different event than if the cord were pulled—including motion alarms or passive check-in. It detects motion up to 20 ft at an angle of 45º vertically and horizontally. A jumper on the back of the device allows you to set various detection intervals: 5- or 60-minute between transmissions. Motion alarms must be configured to clear from the desk console. The WMTA provides all of the above features, but uses a push-for-help button rather than a pull-for-help cord. Side View
20’
Device Code: One code for motion and one for pull cord/touch pad.
45º
No Jumper — The WMCA will not transmit again for a minimum of 5 minutes.
Battery Holder: Use 3V lithium battery Panasonic BSG - CR2 or equivalent. (Part# 301013)
5 minute minimum delay between transmissions
60 minute minimum delay between transmissions Silversphere Wireless Series
© 2014 Silversphere - Doc.Wireless Series 0214
Companion One Silversphere pendants allow for wireless activation of an emergency call from anywhere within a resident’s apartment or common area. These transmitters can be used within a fully wireless system or as an added feature to a hardwired system. When activated, WATC wireless pendants send a signal to WRMA hardwired RF receivers and WAPA wireless access point on a wireless system, or they send a signal to WARB hardwired RF receivers on a hardwired system.
around the neck using a safety lanyard, which breaks under pressure to prevent choking. The WATC-W is an adjustable wrist strap accessory for the WATC that was specifically designed for resident comfort.
The WATC wireless pendant is activated by pressing the button. The pendant may be worn Silversphere wireless universal transmitters allow for wireless activation of an alarm from anywhere within a resident’s apartment or common area. When activated, universal transmitters send a signal to WRMA hardwired RF receivers and WAPA wireless access points on a wireless system, or they send a signal to WARB hardwired RF receivers on a hardwired system.
Pendant Accessories WATC-W Wrist Strap Accessory 693405
Repalcement Lanyard
configuration may be selected with the use of a shunt. (See diagram on following page.) The WUTB-RS operates the similarly to a standard WUTA, but also includes a magnetic reed switch.
The WUTA is activated by triggering the programmable input channel, which is connected to an external dry contact at installation. It is triggered by an open-state on a normally closed contact, or a closedstate on a normally open contact. Either
The WDBA is a door bell which includes the push button and single-gang fixture.
WUTA (Left), WDBA (Center) WMDA (Right)
Silversphere Wireless Series
© 2014 Silversphere - Doc.Wireless Series 0214
Companion One WUTA
Yes
Universal Transmitters
(Dimensions:
4”x 1”x 1.25” in casing)
No
N.C.
Use jumper to disable the WUTA reset option: Yes Send a reset when the condition resets. No Do not send a reset when the condition resets. Screw terminal for dry contact
Use jumper to set your WUTA condition: N.O. Normally Open N.C. Normally Closed
Mounting Requirements The WUTA universal transmitter is designed to be mounted on a wall or doorway using the provided double-sided foam tape. For rugged applications, the WUTA can also be mounted using the provided screws via two screw holes located inside the unit. The screw holes are on the circuit board and exit through the back of the product.
Connect wires to screw terminal located at the bottom. Note: there should be absolutely no voltage on the dry contact.
N.O.
l DO
NOT overtighten the screws. l DO NOT use drywall screws.
l AVOID mounting on metal frames. (See WUTB-RS)
Silversphere Wireless Series
© 2014 Silversphere - Doc.Wireless Series 0214
Companion One WUTB-RS
Yes
Universal Transmitters
(Dimensions:
4”x 1”x 1.25” in casing)
No
N.C.
Use jumper to disable the WUTB-RS reset option: Yes Send a reset when the condition resets. No Do not send a reset when the condition resets. Magnetic & Reed Switch
N.O.
Screw terminal for dry contact
Use either a magnet and the magnetic reed-switch mounted on the side of the WUTB-RS, or use a pair of wires and the dry contacts located at the bottom. Note: there should be absolutely no voltage on the dry contact.
Use jumper to set your WUTB-RS condition: N.O. Normally Open N.C. Normally Closed
Mounting Requirements The WUTB-RS universal transmitter is designed to be mounted using the provided double-sided foam tape. For rugged applications, the WUTB-RS can also be mounted using the provided screws via two screw holes located inside the unit. The screw holes are on the circuit board and exit through the back of the product. l DO NOT overtighten the screws. l DO NOT use drywall screws. l If mounting on metal surfaces, such as door frames, use WUTB-RS.
Silversphere Wireless Series
© 2014 Silversphere - Doc.Wireless Series 0214
Companion One Pendants WATC-WH WATC-BK WATC-PI WATC-PR WATC-SR-WH WATC-SR-BK WATC-SR-PI WATC-SR-PR
Resident Pendant — White Resident Pendant — Black Resident Pendant — Pink Resident Pendant — Purple Staff Reset Pendant — White Staff Reset Pendant — Black Staff Reset Pendant — Pink Staff Reset Pendant — Purple
Stations and Universal Transmitters WCCA Wireless Call Cord Station WCCA-3 Wireless Call Cord Station (3-Gang) WCCA-NC Wireless Bed Pressure Pad Station WMDA Motion Detector w/ Attached WUTA WRCB Emergency Call Pull Station w/ Check-in, Reset & Temperature WRTB Emergency Call Touch Pad w/ Check-in, Reset & Temperature WUTB-RS Universal Transmitter w/ Onboard Reed Switch WDBA Door Bell Transmitter WCUA Emergency Call Pull Station w/ Check-in, Reset & N.O. Dry Contact WTUA Emergency Call Touch Pad w/ Check-in, Reset & N.O. Dry Contact WURA Universal Reset Station with Check-in WMCA Emergency Call Pull Station w/ Check-in, Reset & Built-in Motion Sensor WMTA Emergency Call Touch Pad w/ Check-in, Reset & Built-in Motion Sensor Replacement Batteries Part Number 301003
Description 3.6V "Barrell"
301004
3V CR2032 "Coin Cell"
301006
3V CD2450 Larger "Coin Cell"
301013
3V Lithium
For use with… WGPA (Device no longer available) Replace with WUTA or WUTB-RS WRCA, WRCA-T, WRTA, WRTA-T, WURA, WTUA, WCUA, WDBA WUTA, WCCA, WCCA-NC WUTB-RS, WMCA, WRCB, WRTB, WMTA
Silversphere Wireless Series
© 2014 Silversphere - Doc.Wireless Series 0214