Simple Rail - Simplified Building
Simple Rail Surface L160 Kit Instructions
Parts Grab Rail
Surface L160 Parts Qty Part 2 62-7 Standard Railing Flanges 2 L160 Smooth Handrail Fittings 4 84-7 Malleable Plugs 2 Posts (Cut @ 3’) 1 Grab Rail (Cut @ your custom length) 1 99-7 Allen Key
Post 84-7 L160-7 84-7
Tools • Allen Key (included) • Rubber Mallet/Hammer (for plugs) • Drill/Hammer Drill • Wrench
Hardware Included
62-7
• 4 x ½” Sleeve Anchors (Concrete/Brick) • 4 x ½” Lag Screws (Wood) • 2 x Box Bolts (Upright) • 4 x Stainless Steel Screws (Grab Rail)
Installation Tips 1. 2. 3. 4.
Confirm that you have all the required parts. When installing plugs, place rag/cardboard over plug and hammer into place. If installing into concrete/brick, vacuum out debris from drilled out holes before inserting anchor bolts. If you plan on painting your rail, do so before assembling.
Step by Step 1. Insert posts into 62-7’s. Tighten set screws loosely. 2. Line up assembled posts to desired location. Test grab bar with posts, then mark holes for the 62-7’s.
5. Drill 5/8” hole where marked on post. Insert Box Bolts into L160-7’s and through the 5/8” hole. Tighten Box Bolt using a pair of wrenches. 6. Line up grab rail at desired location. Mark and drill pilot holes for securing grab rail to L160-7’s.
3. Disassemble the posts and secure 62-7’s to surface. 7. Attach grab rail with stainless steel screws and adjust as needed. 4. Insert posts into 62-7’s and mark holes for L160-7’s (Approx. 2” below the top of post).
8. Cover 84-7’s with a rag or cardboard and hammer into place.
Page 1
Parts Grab Rail
Surface L160 Parts Qty Part 2 62-7 Standard Railing Flanges 2 L160 Smooth Handrail Fittings 4 84-7 Malleable Plugs 2 Posts (Cut @ 3’) 1 Grab Rail (Cut @ your custom length) 1 99-7 Allen Key
Post 84-7 L160-7 84-7
Tools • Allen Key (included) • Rubber Mallet/Hammer (for plugs) • Drill/Hammer Drill • Wrench
Hardware Included
62-7
• 4 x ½” Sleeve Anchors (Concrete/Brick) • 4 x ½” Lag Screws (Wood) • 2 x Box Bolts (Upright) • 4 x Stainless Steel Screws (Grab Rail)
Installation Tips 1. 2. 3. 4.
Confirm that you have all the required parts. When installing plugs, place rag/cardboard over plug and hammer into place. If installing into concrete/brick, vacuum out debris from drilled out holes before inserting anchor bolts. If you plan on painting your rail, do so before assembling.
Step by Step 1. Insert posts into 62-7’s. Tighten set screws loosely. 2. Line up assembled posts to desired location. Test grab bar with posts, then mark holes for the 62-7’s.
5. Drill 5/8” hole where marked on post. Insert Box Bolts into L160-7’s and through the 5/8” hole. Tighten Box Bolt using a pair of wrenches. 6. Line up grab rail at desired location. Mark and drill pilot holes for securing grab rail to L160-7’s.
3. Disassemble the posts and secure 62-7’s to surface. 7. Attach grab rail with stainless steel screws and adjust as needed. 4. Insert posts into 62-7’s and mark holes for L160-7’s (Approx. 2” below the top of post).
8. Cover 84-7’s with a rag or cardboard and hammer into place.
Page 1
