SS2000Fire install AWS
Safety Technology International, Inc.
Safety Technology International (Europe) Ltd.
2306 Airport Road • Waterford, Michigan 48327-1209 Phone: 248-673-9898 • Fax: 248-673-1246 Toll Free: 800-888-4784 • E-mail: [email protected] Web: www.sti-usa.com
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch Worcestershire • B98 0HU • England • Tel: 44 (0) 1527 520 999 Fax: 44 (0) 1527 501 999 • Freephone: 0800 085 1678 (UK only) E-mail: [email protected] • Web: www.sti-europe.com
PRODUCT DIMENSIONS 1.62 in. (41mm)
3.25 in. (82mm)
2.25 in. (57mm)
STANDARD SINGLE OUTLET BOX NOTE: TO MOUNT STOPPER STATION SS-2000F ON A STANDARD OUTLET BOX SUB-102722-R IS REQUIRED
INSERT TERMINAL BLOCK NOTCH AS SHOWN AND ROTATE UPWARD.
INSTALLATION OF TERMINAL BLOCKS
TO PROVIDE ADEQUATE CLEARANCE FOR INSTALLATION TO ANY STANDARD SINGLE GANG OUTLET BOX, THE SUB-102722-R SPACER IS REQ
4.87 in. (124mm)
SUB-102722-R PLASTIC SPACER MOLDED IN RED (OPTIONAL) TERMINAL BLOCK ASSEMBLY 10197H CONTACT HOLDER BACKPLATE ASSEMBLY WITH STAINLESS STEEL GROUND PLATE AND LUG SCREWS (2) PROVIDED 19010 #6-32 x 1 in. WITHOUT SUB-102722-R 19045 #6-22 x 1 1/2 in. WITH SUB-102722-R
.69 in. (17mm)
MOLDED BUTTON WITH KEY RESET BUTTON LOCK NUT
P
REMOVAL OF TERMINAL BLOCKS
MOLDED POLYCARBONATE FACEPLATE
US
h
HERE
A
E F I R
PRY BACK LEVER 'A' IN DIRECTION OF ARROW THEN USING A FLATHEAD SCREW DRIVER, INSERT AS SHOWN AND ROTATE UPWARD.
TURN CLOCKWISE ONE QUARTER TURN TO RESET
19001 HOUSING RETENTION SCREW #8-32 x 3/8 in. (1) PROVIDED
19030 KEY (2) PROVIDED
19015 3/32 in. ALLEN WRENCH (1) PROVIDED
Electronic warranty form at www.sti-usa.com/wc14
INSTALLATION OF SS-2000 FIRE SERIES STOPPER® STATION All specifications and information shown were current as of publication, and are subject to change without notice.
ADA
SHEET 1 10277IS JAN99
compliant
12-18 AWG IF LAST STATION ON CIRCUIT, CONNECT E.O.L. RESISTOR
CLOSE ON ALARM CAUTION AN UNINSULATED SECTION OF A SINGLE CONDUCTOR SHOULD NOT BE LOOPED AROUND THE TERMINAL AND SERVE AS TWO CONNECTIONS. THE WIRE MUST BE SEVERED, THEREBY PROVIDING SUPERVISION OF THE CONNECTION IN THE EVENT THE WIRE BECOMES DISLODGED FROM THE DEVICE.
BE SURE ALL ELECTRICAL POWER IS DISCONNECTED BEFORE STARTING THE INSTALLATION. NOTE: JUMPER NOT PROVIDED
SINGLE DEVICE
12-18 AWG
CLOSE ON ALARM
CLOSE ON ALARM INCOMING
10196 N.O. TERMINAL BLOCK (2) PROVIDED UP TO 3 TERMINALS MAY BE USED FOR EACH STATION ASSEMBLY.
OUTGOING
A
DIAGRAM DEPICTING MULTIPLE DEVICES
SUPERVISED LOOP (SEE CAUTION NOTE)
ALL TERMINALS ACCEPT TWO 12 TO 18 (AWG) VOLTAGE
RATED AVERAGE CURRENT
250 VDC 24 VAC
1 AMP 3 AMP
BUTTON LOCK NUT METAL WASHER
TO SEPARATE TERMINAL AND BUTTON ASSEMBLY GRASP TERMINAL HOUSING, USING THUMB APPLY PRESSURE DOWNWARD, REMOVE TERMINAL HOUSING AS SHOWN.
TERMINAL BLOCK RELEASE LEVER MUST FACE UPWARD AS SHOWN FOR SWITCH TO FUNCTION CORRECTLY.
REMOVAL OF TERMINAL BLOCK FROM TERMINAL HOUSING INSERT SMALL SCREWDRIVER AS SHOWN AND PRY UPWARD, REMOVE TERMINAL.
STRIP 1/4 in. OF WIRE INSULATION, INSERT IN TERMINAL (AS SHOWN). THEN USING A PHILLIPS SCREWDRIVER TURN CLOCKWISE UNTIL TIGHT.
ELECTRICAL TERMINAL 1, 2, OR 3 TERMINALS MAY BE USED VIEW IN DIRECTIONS OF ARROW
BACKPLATE ASSEMBLY VIEW IN DIRECTIONS OF ARROW
A
INSTALLATION OF ELECTRICAL WIRE INTO TERMINAL BLOCK
INSERT NOTCH AS SHOWN THEN ROTATE UPWARD
A
INSTALLATION AND REMOVAL OF TERMINAL BLOCKS AND TERMINAL BLOCK ASSEMBLY FROM BUTTON ASSEMBLY
SAFETY TECHNOLOGY INTERNATIONAL, INC. • 2306 AIRPORT ROAD • WATERFORD • MICHIGAN 48327-1209 • PHONE: 248-673-9898 • FAX: 248-673-1246 • INFO @ www.sti-usa.com
SHT. 2 10277IS JAN99
Safety Technology International (Europe) Ltd.
2306 Airport Road • Waterford, Michigan 48327-1209 Phone: 248-673-9898 • Fax: 248-673-1246 Toll Free: 800-888-4784 • E-mail: [email protected] Web: www.sti-usa.com
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch Worcestershire • B98 0HU • England • Tel: 44 (0) 1527 520 999 Fax: 44 (0) 1527 501 999 • Freephone: 0800 085 1678 (UK only) E-mail: [email protected] • Web: www.sti-europe.com
PRODUCT DIMENSIONS 1.62 in. (41mm)
3.25 in. (82mm)
2.25 in. (57mm)
STANDARD SINGLE OUTLET BOX NOTE: TO MOUNT STOPPER STATION SS-2000F ON A STANDARD OUTLET BOX SUB-102722-R IS REQUIRED
INSERT TERMINAL BLOCK NOTCH AS SHOWN AND ROTATE UPWARD.
INSTALLATION OF TERMINAL BLOCKS
TO PROVIDE ADEQUATE CLEARANCE FOR INSTALLATION TO ANY STANDARD SINGLE GANG OUTLET BOX, THE SUB-102722-R SPACER IS REQ
4.87 in. (124mm)
SUB-102722-R PLASTIC SPACER MOLDED IN RED (OPTIONAL) TERMINAL BLOCK ASSEMBLY 10197H CONTACT HOLDER BACKPLATE ASSEMBLY WITH STAINLESS STEEL GROUND PLATE AND LUG SCREWS (2) PROVIDED 19010 #6-32 x 1 in. WITHOUT SUB-102722-R 19045 #6-22 x 1 1/2 in. WITH SUB-102722-R
.69 in. (17mm)
MOLDED BUTTON WITH KEY RESET BUTTON LOCK NUT
P
REMOVAL OF TERMINAL BLOCKS
MOLDED POLYCARBONATE FACEPLATE
US
h
HERE
A
E F I R
PRY BACK LEVER 'A' IN DIRECTION OF ARROW THEN USING A FLATHEAD SCREW DRIVER, INSERT AS SHOWN AND ROTATE UPWARD.
TURN CLOCKWISE ONE QUARTER TURN TO RESET
19001 HOUSING RETENTION SCREW #8-32 x 3/8 in. (1) PROVIDED
19030 KEY (2) PROVIDED
19015 3/32 in. ALLEN WRENCH (1) PROVIDED
Electronic warranty form at www.sti-usa.com/wc14
INSTALLATION OF SS-2000 FIRE SERIES STOPPER® STATION All specifications and information shown were current as of publication, and are subject to change without notice.
ADA
SHEET 1 10277IS JAN99
compliant
12-18 AWG IF LAST STATION ON CIRCUIT, CONNECT E.O.L. RESISTOR
CLOSE ON ALARM CAUTION AN UNINSULATED SECTION OF A SINGLE CONDUCTOR SHOULD NOT BE LOOPED AROUND THE TERMINAL AND SERVE AS TWO CONNECTIONS. THE WIRE MUST BE SEVERED, THEREBY PROVIDING SUPERVISION OF THE CONNECTION IN THE EVENT THE WIRE BECOMES DISLODGED FROM THE DEVICE.
BE SURE ALL ELECTRICAL POWER IS DISCONNECTED BEFORE STARTING THE INSTALLATION. NOTE: JUMPER NOT PROVIDED
SINGLE DEVICE
12-18 AWG
CLOSE ON ALARM
CLOSE ON ALARM INCOMING
10196 N.O. TERMINAL BLOCK (2) PROVIDED UP TO 3 TERMINALS MAY BE USED FOR EACH STATION ASSEMBLY.
OUTGOING
A
DIAGRAM DEPICTING MULTIPLE DEVICES
SUPERVISED LOOP (SEE CAUTION NOTE)
ALL TERMINALS ACCEPT TWO 12 TO 18 (AWG) VOLTAGE
RATED AVERAGE CURRENT
250 VDC 24 VAC
1 AMP 3 AMP
BUTTON LOCK NUT METAL WASHER
TO SEPARATE TERMINAL AND BUTTON ASSEMBLY GRASP TERMINAL HOUSING, USING THUMB APPLY PRESSURE DOWNWARD, REMOVE TERMINAL HOUSING AS SHOWN.
TERMINAL BLOCK RELEASE LEVER MUST FACE UPWARD AS SHOWN FOR SWITCH TO FUNCTION CORRECTLY.
REMOVAL OF TERMINAL BLOCK FROM TERMINAL HOUSING INSERT SMALL SCREWDRIVER AS SHOWN AND PRY UPWARD, REMOVE TERMINAL.
STRIP 1/4 in. OF WIRE INSULATION, INSERT IN TERMINAL (AS SHOWN). THEN USING A PHILLIPS SCREWDRIVER TURN CLOCKWISE UNTIL TIGHT.
ELECTRICAL TERMINAL 1, 2, OR 3 TERMINALS MAY BE USED VIEW IN DIRECTIONS OF ARROW
BACKPLATE ASSEMBLY VIEW IN DIRECTIONS OF ARROW
A
INSTALLATION OF ELECTRICAL WIRE INTO TERMINAL BLOCK
INSERT NOTCH AS SHOWN THEN ROTATE UPWARD
A
INSTALLATION AND REMOVAL OF TERMINAL BLOCKS AND TERMINAL BLOCK ASSEMBLY FROM BUTTON ASSEMBLY
SAFETY TECHNOLOGY INTERNATIONAL, INC. • 2306 AIRPORT ROAD • WATERFORD • MICHIGAN 48327-1209 • PHONE: 248-673-9898 • FAX: 248-673-1246 • INFO @ www.sti-usa.com
SHT. 2 10277IS JAN99
