Sub-Zero Design Guide - Subzero Wolf

DESIGN GUIDE REVISED 9 / 2017

TA B L E O F C O N T E N T S

3

B U I L T- I N R E F R I G E R A T I O N

40

P R O 4 8 R E F R I G E R AT I O N

46

I N T E G R AT E D R E F R I G E R AT I O N

56

WINE STORAGE

88

U N D E R C O U N T E R R E F R I G E R AT I O N

98

SUB-ZERO WARRANTIES

Features and specifications are subject to change at any time without notice. Visit subzero.com/specs for the most up-to-date information. Throughout this guide, dimensions may vary by ± 1/8" (3). Dimensions in parentheses are millimeters unless otherwise specified.

B U I L T- I N

B UILT-IN R EF R IGE RATION

Built-In Refrigeration

I N T E G R AT E D

PRO 48

For the built-in line, Sub-Zero designers and engineers took a fresh look at everything, inside and out. Exterior refinements include redesigned grilles and lower-profile hinges. Inside, new technology in food preservation makes the builtin line nothing short of revolutionary.

B UILT-IN MO DELS

BI-36R

BI-42UFD(ID)

BI-36F

BI-36S

UNDERCOUNTER

WINE

BI-36UFD(ID)

BI-36RG

4

|

Sub-Zero Customer Care 800.222.7820

BI-30U

BI-42S(ID)

BI-30UG

BI-42SD

BI-36U(ID)

BI-48S(ID)

BI-36UG

BI-48S

B UILT-IN R EF R IGE RATION

B U I L T- I N

Specifications INTERIOR CAPACITY— CU FT

(L )

A L L R E F R I G E R AT O R | ALL FREE Z E R

BI-36R BI-36RG BI-36F OV E R - A N D - U N D E R

SI D E - B Y- S I D E

22.7 (643) REFR

FRZR

13.2 (374) 13.1 (371) 16.4 (464) 16.3 (462) 15.7 (445) 17.9 (507)

4.2 (119) 4.2 (119) 5.3 (150) 5.3 (150) 5.3 (150) 6.3 (178)

REFR

FRZR

12.4 (351) 16.3 (462) 15.8 (447) 16.0 (453) 19.1 (541) 18.6 (527) 18.8 (532)

8.2 (232) 8.0 (227) 7.9 (224) 7.9 (224) 9.8 (278) 9.6 (272) 9.6 (272)

I N T E G R AT E D

BI-36S BI-42S BI-42SID BI-42SD BI-48S BI-48SID BI-48SD

FRZR

PRO 48

BI-30U BI-30UG BI-36U(ID) BI-36UG BI-36UFD(ID) BI-42UFD(ID)

REFR

23.5 (665) 23.4 (663)

WINE

|

5

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

B UILT-IN R EF R IGE RATION

PRO 48

Built-In Design Options F R AMED

O VER LAY

For the classic Sub-Zero look, choose framed custom door panels that contrast with the stainless steel full-length handles and louvered grille (shown). The framed application is an overlay model with framed design features. Panel, grille and handle options are available.

Custom overlay door panels can be combined with unique handle hardware for design flexibility. Shown with pro handle option to complement Wolf ranges. Customize with panel, grille and handle options.

Panels | Custom panels, stainless steel or white enamel. Grille | Classic louvered grille insert or solid custom panel for 84" (standard), 83" or 88" overall unit height. Dual wide grille for dual installations.

Panels | Custom panels or stainless steel. Grille | Solid custom panel or pro louvered grille for 84" (standard), 83" or 88" overall unit height. Dual wide grille for dual installations. Handles | Custom, tubular or pro handles.

UNDERCOUNTER

WINE

I N T E G R AT E D

Handles | Full-length standard or extended.

Framed.

6

|

Sub-Zero Customer Care 800.222.7820

Overlay.

B UILT-IN R EF R IGE RATION

B U I L T- I N

Built-In Design Options F LUS H INS ET

S TA I N LES S S TEEL

The flush inset design option allows for flush door and grille panels and custom handle hardware. Shown with tubular handle option to match Wolf built-in ovens. The flush inset application is an overlay model with flush inset panels. Customize with panel, grille and handle options.

For a professional look, classic stainless steel models require no customization. To complement the look of Wolf ranges, choose the pro handle option (shown). Grille and handle options are available.

Grille | Solid custom panel or pro louvered grille for 84" (standard), 83" or 88" overall unit height. Dual wide grille for dual installations.

Grille | Pro louvered grille for 84" (standard), 83" or 88" overall unit height. Dual wide grille for dual installations.

PRO 48

Panels | Custom panels or stainless steel.

Handles | Tubular or pro handles.

Handles | Custom, tubular or pro handles.

I N T E G R AT E D WINE

Stainless steel.

subzero.com/specs

|

7

UNDERCOUNTER

Flush inset.

B U I L T- I N

B UILT-IN R EF R IGE RATION

Overall Dimensions A L L R EF R IG ER ATOR | AL L FRE E Z E R 26 3/16" (665)

PRO 48

36" (914)

84"

(2134)

73 3/4"

I N T E G R AT E D

(1873)

HEIGHT DIMENSIONS ± 1/2" (13)

4" (102)

23 7/8" (606)

14 1/8" (359)

37 1/4"

WINE

(946)

2 3/8" (60)

UNDERCOUNTER

Model BI-36R, BI-36RG, BI-36F.

8

|

Sub-Zero Customer Care 800.222.7820

23 7/8" (606)

Overall dimensions are based on stainless steel models. For flush inset applications, add 1/2" (13) to door clearance dimensions.

B UILT-IN R EF R IGE RATION

B U I L T- I N

Overall Dimensions O VER -AND-UND E R 26 3/16" (665)

30" (762)

26 3/16" (665)

36" (914)

(2134)

50 3/4"

50 3/4"

(1289)

(1289)

23"

23"

4" (102)

HEIGHT DIMENSIONS ± 1/2" (13)

23 7/8" (606)

(606)

(606)

14 1/8"

12 1/8" (308)

(600)

23 7/8" (606)

23 7/8"

23 7/8"

23 5/8"

4" (102)

I N T E G R AT E D

(584)

(584)

HEIGHT DIMENSIONS ± 1/2" (13)

PRO 48

84"

84"

(2134)

(359)

311/4" (796)

23 5/8" (600)

37 1/4" (946)

WINE

2 3/8" (60) 2 3/8" (60)

Model BI-30U, BI-30UG.

Model BI-36U(ID), BI-36UG.

|

9

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

B UILT-IN R EF R IGE RATION

Overall Dimensions O VER -AND-UND E R 26 3/16" (665)

PRO 48

36" (914)

26 3/16" (665)

42" (1067)

84"

84"

(2134)

(2134)

50 3/4"

50 3/4" (1289)

(1289)

23"

23"

I N T E G R AT E D

(584)

HEIGHT DIMENSIONS ± 1/2" (13)

(584)

4" (102)

HEIGHT DIMENSIONS ± 1/2" (13)

23 7/8" (606)

23 7/8"

4" (102)

23 7/8"

(606)

(606)

8"

9"

(203)

(229)

23 5/8"

191/2" 23 5/8" (495)

(600)

(600)

221/4"

WINE

(565)

2 3/8" (60)

UNDERCOUNTER

Model BI-36UFD(ID).

10

|

Sub-Zero Customer Care 800.222.7820

2 3/8" (60)

Model BI-42UFD(ID).

23 7/8" (606)

B UILT-IN R EF R IGE RATION

B U I L T- I N

Overall Dimensions S I DE-B Y-S IDE 26 3/16" (665)

36" (914)

(2134)

73 3/4"

73 3/4"

(1873)

(1873)

HEIGHT DIMENSIONS ± 1/2" (13)

23 7/8" (606)

4" (102)

23 7/8" (606)

23 7/8" (606)

(606)

7 1/2" (191)

8 3/4" (222)

I N T E G R AT E D

4" (102)

23 7/8" 7 1/4" (184)

PRO 48

84"

84"

(2134)

HEIGHT DIMENSIONS ± 1/2" (13)

26 3/16" (665)

42" (1067)

10 3/8" (264)

26 1/4"

221/4"

(668)

(565)

WINE

2 3/8" (60) 2 3/8" (60)

Model BI-36S.

Model BI-42S(ID), BI-42SD.

|

11

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

B UILT-IN R EF R IGE RATION

Overall Dimensions S I DE-B Y-S IDE 26 3/16" (665)

PRO 48

48" (1219)

84"

(2134)

73 3/4"

I N T E G R AT E D

(1873)

HEIGHT DIMENSIONS ± 1/2" (13)

4" (102)

23 7/8" (606)

8 3/8" (213)

11 5/8" (295)

30"

WINE

(762)

2 3/8" (60)

UNDERCOUNTER

Model BI-48S(ID), BI-48SD.

12

|

Sub-Zero Customer Care 800.222.7820

23 7/8" (606)

B UILT-IN R EF R IGE RATION

B U I L T- I N

Specifications SHIPPING WEIGHT A L L R E F R I G E R AT O R | ALL FREE Z E R

BI-36R BI-36RG BI-36F OV E R - A N D - U N D E R

SI D E - B Y- S I D E

L B (KG )

538 (244) 582 (264) 608 (276) 608 (276) 630 (286) 656 (298) 656 (298)

I N T E G R AT E D

BI-36S BI-42S BI-42SID BI-42SD BI-48S BI-48SID BI-48SD

L B (KG )

462 (210) 476 (216) 515 (234) 529 (240) 529 (240) 582 (264)

PRO 48

BI-30U BI-30UG BI-36U(ID) BI-36UG BI-36UFD(ID) BI-42UFD(ID)

L B (KG )

420 (191) 430 (195) 406 (184)

Shipping weights are based on stainless steel models.

WINE

|

13

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

B UILT-IN R EF R IGE RATION

Opening Dimensions S TANDAR D INS TAL L ATION

24" (610) OPENING DEPTH

3/4" (19) TYPICAL

3 1/2" (89)

PRO 48

FINISHED RETURN

TOP VIEW

W FRAMELESS CABINETRY

3/4" (19) TYPICAL

3 1/2" (89)

I N T E G R AT E D

FINISHED RETURN

83 3/4"

W

(2127) OPENING HEIGHT

OPENING WIDTH

WINE

SIDE VIEW

W FRAMED CABINETRY

FRONT VIEW

NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry. Shaded line represents profile of unit.

OPENING WIDTH

UNDERCOUNTER

FILLER

W

30" Model

29 1/2" (749)

36" Model

35 1/2" (902)

42" Model

41 1/2" (1054)

48" Model

47 1/2"

14

|

Sub-Zero Customer Care 800.222.7820

(1206)

If an 83" (2108) grille height is specified, the opening height must be decreased by 7/8" (22). If an 88" (2235) grille height is specified, the opening height must be increased by 4" (102). If two units are installed side by side, refer to page 16 for dual standard installations.

B UILT-IN R EF R IGE RATION

B U I L T- I N

Opening Dimensions F LUS H INS ET INSTAL L ATION

26 3/16" (665) FLUSH INSET DEPTH

5 11/16" 3 1/2"

2 3/16" (56)

FINISHED CLEATS

TOP VIEW

CLEAT 3/4" (19) TYPICAL

PRO 48

(89) (145) FINISHED RETURN

W FRAMELESS CABINETRY

11/4"

1/4" (6)

(32)

5 11/16" 3 1/2"

(89) (145) FINISHED RETURN

W FLUSH INSET WIDTH

3/4" (19) TYPICAL

I N T E G R AT E D

SIDE VIEW

84" (2134) FLUSH INSET HEIGHT

CLEAT FILLER

W FRAMED CABINETRY

FRONT VIEW

WINE

NOTE: 3 1/2" (89) finished returns and shaded areas will be visible and should be finished to match cabinetry. Shaded line represents profile of unit with 3/4" (19) panel.

FLUSH INSET WIDTH

W

30" Model

32" (813)

36" Model

38" (965)

42" Model

44" (1118)

48" Model

50" (1270)

Dimensions assume a 3/4" (19) panel thickness. If an 83" (2108) grille height is specified, the flush inset height must be decreased by 7/8" (22). If an 88" (2235) grille height is specified, the flush inset height must be increased by 4" (102).

subzero.com/specs

|

15

UNDERCOUNTER

If two units are installed side by side, refer to page 17 for dual flush inset installations.

B U I L T- I N

B UILT-IN R EF R IGE RATION

Opening Dimensions D U AL S TANDARD INSTAL L ATION

24" (610) OPENING DEPTH

3/4" (19) TYPICAL

3 1/2" (89)

PRO 48

FINISHED RETURN

TOP VIEW

W FRAMELESS CABINETRY

3/4" (19) TYPICAL

3 1/2" (89)

I N T E G R AT E D

FINISHED RETURN

83 3/4"

W

(2127) OPENING HEIGHT

OPENING WIDTH

WINE

SIDE VIEW

W FRAMED CABINETRY

FRONT VIEW

NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry. Shaded line represents profile of unit.

DUAL OPENING WIDTH

UNDERCOUNTER

FILLER

W

Two 30" Models

59 3/4" (1518)

30" and 36" Models

65 3/4" (1670)

Two 36" Models

71 3/4" (1822)

16

|

Sub-Zero Customer Care 800.222.7820

A dual installation kit will be required for this installation.

B UILT-IN R EF R IGE RATION

B U I L T- I N

Opening Dimensions D U AL F LUS H IN SE T INSTAL L ATION

26 3/16" (665) FLUSH INSET DEPTH

5 11/16" 3 1/2"

2 3/16" (56)

FINISHED CLEATS

TOP VIEW

CLEAT 3/4" (19) TYPICAL

PRO 48

(89) (145) FINISHED RETURN

W FRAMELESS CABINETRY

11/4"

1/4" (6)

(32)

5 11/16" 3 1/2"

(89) (145) FINISHED RETURN

W FLUSH INSET WIDTH

SIDE VIEW

3/4" (19) TYPICAL

I N T E G R AT E D

84" (2134) FLUSH INSET HEIGHT

CLEAT FILLER

W FRAMED CABINETRY

FRONT VIEW

WINE

NOTE: 3 1/2" (89) finished returns and shaded areas will be visible and should be finished to match cabinetry. Shaded line represents profile of unit with 3/4" (19) panel.

DUAL FLUSH INSET WIDTH

W

Two 30" Models

62 1/4" (1581)

30" and 36" Models

68 1/4" (1734)

Two 36" Models

74 1/4" (1886)

Dimensions assume a 3/4" (19) panel thickness. A dual installation kit will be required for this installation.

|

17

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

B UILT-IN R EF R IGE RATION

Electrical

Plumbing

The electrical supply should be located within the shaded area shown in the illustration below. A separate circuit servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

The water supply line should be located within the shaded area shown in the illustration below. The water supply line should be connected to the house supply with an easily accessible shut-off valve. Do not use self‑piercing valves. The water supply line must not interfere with installation of the anti-tip brackets.

PRO 48

Installation must comply with all applicable electrical codes. ELECTRICAL REQUIREMENTS

Electrical Supply

115 VAC, 60 Hz

Service

15 amp dedicated circuit

Receptacle

3-prong grounding-type

A reverse osmosis system can be used provided there is constant water pressure of 35–120 psi (2.4–8.3 bar) supplied to the unit at all times. A copper line is not recommended for this application. Installation must comply with all applicable plumbing codes. PLUMBING REQUIREMENTS 1/4"

Water Supply Pressure 7"

E

I N T E G R AT E D

(178)

35–120 psi (2.4–8.3 bar)

Excess Line for Connection

6"

(152)

75 1/2" (1918) FROM FLOOR RIGHT SIDE OF OPENING RIGHT SIDE OF OPENING

Electrical supply location.

18" (457)

6" (152) 3" (76)

AREA EXTENDS 1/2" (13)

UNDERCOUNTER

WINE

FORWARD ON FLOOR

Water supply location.

18

|

Sub-Zero Customer Care 800.222.7820

OD copper, braided stainless steel or PEX tubing 36" (914)

B UILT-IN R EF R IGE RATION

B U I L T- I N

Custom Panels For framed, overlay and flush inset applications, custom door panels must be provided. Handle hardware must also be provided for overlay and flush inset applications. Refer to panel requirements below and the charts on pages 22–27 for custom panel dimensions for your specific design application.

Finish all sides of the custom panels. They may be visible when the door is open or through the window of glass door models. PANEL REQUIREMENTS W E I G H T P E R PA N E L

BI-36R, BI-36RG, BI-36F All Other Models Grille Panel

If the custom panel is thinner than 1/4" (6), a filler material must be added to achieve a proper fit. If the panel is thicker than 1/4" (6), rout an edge around the panel or mount the custom panel on a sheet of 1/4" (6) thick material and insert into the channel. Refer to the illustrations below. Routing, recessing or optional extended handles may be required for finger clearance. Refer to the full-scale template on page 34. When installing two units side by side, refer to page 16 for dual standard installations.

75 lb (34 kg) 50 lb (23 kg) 13 lb (6 kg) MIN 1/4" 5/8"

1/4" (6) TRIM REVEAL

(6)

(16)

1/4" (6) PANEL

DOOR

Panel 1/4" thick or less.

1/4" (6) min

I N T E G R AT E D

PA N E L T H I C K N E S S

Framed Overlay and Flush Inset

MA X

The framed application is an overlay model with framed design features. It is not a separate model.

PRO 48

IMPORTANT NOTE: Do not cover a glass door with a solid

panel.

FR AM ED PAN ELS

ROUT TO 1/4" (6)

DOOR

Panel thicker than 1/4".

WINE

|

19

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

B UILT-IN R EF R IGE RATION

PRO 48

Custom Panels PART IAL F R AME D OPTION

PAN EL M O U N TI N G K I T

The partial framed kit includes a stainless steel panel for above and below the external dispenser. Refer to the chart below for panel width. The kit is avail­able through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com.

A Sub-Zero custom panel mounting kit eliminates the need for a backer and spacer panel and is avail­able through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. The kit consists of mounting cleats, screws and gages used to properly position the cleats. The kit is available for all built-in models except glass door models. Dual installations require two mounting kits.

PARTIAL FRAMED PANEL

W

BI-42SD

15 1/16"

(383)

BI-48SD

18 3/4"

(476)

O VER LAY PA N ELS

Overlay panels are typically created by combining a 3/4" (19) custom panel, a .10" (3) spacer panel and a 1/4" (6) backer panel. Refer to the illustrations below.

I N T E G R AT E D

When installing two units side by side, refer to page 16 for dual standard installations.

CUSTOM PANEL

SPACER PANEL

SPACER PANEL

CUSTOM PANEL

BACKER PANEL

BACKER PANEL

TRIM

5/16" (8) min 1/8" (3) (OVERLAY)

(19) typical

.10" (3) 1/4" (6)

Panel assembly (cross section). Panel assembly (rear view).

WINE UNDERCOUNTER

3/4"

20

|

Sub-Zero Customer Care 800.222.7820

B UILT-IN R EF R IGE RATION

B U I L T- I N

Custom Panels F LUS H INS ET PA NE L S

I C E A N D WATER D I S P EN S ER

The flush inset application is an overlay model with flush inset panels. It is not a separate model.

For models BI-42SD and BI‑48SD, the refrigerator door panel must include a cut-out to accommodate the external dispenser. The thickness of the panel in this area can range from 1/4" (6) to a maximum of 1 1/8" (29). Refer to the illustrations below.

For flush inset panels thicker than 3/4" (19), a 90° door stop may be required to prevent interference with adjacent cabinets. Refer to the full-scale templates at the end of this guide.

PRO 48

The flush inset design allows custom panels to be installed flush with adjacent cabinets. Similar to overlay, flush inset panels are typically created by combining a 3/4" (19) custom panel, a .10" (3) spacer panel and a 1/4" (6) backer panel. Refer to the illustrations for overlay panels.

5/8"

3/32"

1/4"

(16)

(2)

(6)

When installing two units side by side, refer to page 17 for dual flush inset installations.

6 5/16" (160)

6 1/4" (159)

12 7/8"

(327)

(327)

Dispenser dimensions.

I N T E G R AT E D

12 7/8"

Dispenser dimensions.

2"

(51)

WINE

HANDLE GLASSWELL

1"

(25)

Handle placement.

|

21

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

B UILT-IN R EF R IGE RATION

Framed Panel Dimensions H H

H H H

H H A A

H H AH A

A A A

H H

H H H

H AH AH H A AH A

H H

H H AH A

H H

W W W W W

I N T E G R AT E D

BI-30U, BI-36U(ID)

H H H

H H

W

H

35 3/4" (908)

69 9/16" (1767)

W

H H H H H H 8 15/16" (227)

GRI L L E ( O P T I O N A L) H H H H H

35 3/4" (908)

BI-36RG

A

5 3/16A" A(132) A

Stiles | Rails

B B

B A A

10 5/16" (262)

W

(1268)

W

H

29 3/4" (756)

18 11/16" (475)

GRI L L E ( O P T I O N A L)

Grille Panel

H H

H H H

H H

H H H

W W W W W

BI-30UG, BI-36UG

W W W W W

BI-36UFD(ID), BI-42UFD(ID)

REFRIGERATOR

Door Panel FREEZER

Drawer Panel GRIL L E (OPTION AL )

Grille Panel

W

H

35 3/4" (908)

49 15/16" (1268)

W

H

35 3/4" (908)

18 11/16" (475)

W

H

35 3/4" (908)

8 15/16" (227) A

5 3/16" (132)

H

W W W3 W W W W W W W 29 /4" (756) 49 15/16"

FREEZER

Drawer Panel

W W W WWWW W W W

A A A

Stiles | Rails

R E F R I G E R AT O R W W W W W W

H H H

BI-36U G

B B B

MODEL BI-30U, BI-30UG W W W W Door Panel

H H

MODEL BI-36U(ID), BI-36UG

R E F R I G E R AT O R / F RE E Z E R

Grille Panel

A AH A H AH AH H

H H H

MODEL BI-36R, BI-36RG, BI-36F

Door Panel

H H H

H H H

W W W W W

BI-36RG

H H

H H

A A A

B B B

W W W W W

BI-36R, BI-36F

WINE

A A A

A A

B B

H H H

H H A A

PRO 48

H H

H H H

A A A

W

H

29 3/4" (756)

8 15/16" (227)

BI-30UG

Stiles | Rails

A

5 3/16" (132)

MODEL BI-36UFD(ID) REFRIGERATOR (2 PAN EL S)

Door Panel FREEZER

Drawer Panel GRIL L E (OPTION AL )

Grille Panel

W

H

17 5/8" (448)

49 15/16" (1268)

W

H

35 3/4" (908)

18 11/16" (475)

W

H

35 3/4" (908)

8 15/16" (227)

MODEL BI-42UFD(ID) REFRIGERATOR (2 PAN EL S)

Door Panel FREEZER

Drawer Panel UNDERCOUNTER

GRIL L E (OPTION AL )

Grille Panel

22

|

Sub-Zero Customer Care 800.222.7820

W

H

20 5/8" (524)

49 15/16" (1268)

W

H

41 3/4" (1060)

18 11/16" (475)

W

H

41 3/4" (1060)

8 15/16" (227)

B UILT-IN R EF R IGE RATION

WW

AA

HH

HH

B U I L T- I N

HH

WW

BB WW

WW

WW

WW

WW

Framed Panel Dimensions HH

HH

HH

HH

PRO 48

AA BB

WW

WW

BI-36S, BI-42S(ID), BI-48S(ID)

WW

WW

BI-42SD, BI-48SD

MODEL BI-48S, BI-48SID, BI-48SD

R E F R I G E R AT O R

Door Panel

W

H

19 13/16" (503)

69 9/16" (1767)

FREEZER

Door Panel

W

H

15 7/16" (392)

69 9/16" (1767)

GRI L L E ( O P T I O N A L)

Grille Panel

W

H

35 3/4" (908)

8 15/16" (227)

REFRIGERATOR

Door Panel FREEZER

Door Panel GRIL L E (OP TION AL )

Grille Panel BI-48SD

Dispenser Cut-Out*

MODEL BI-42S, BI-42SID, BI-42SD R E F R I G E R AT O R

Door Panel FREEZER

Door Panel GRI L L E ( O P T I O N A L) BI-42SD

Dispenser Cut-Out* Cut-Out Location

H

24 13/16" (630)

69 9/16" (1767)

W

H

16 7/16" (418)

69 9/16" (1767)

W

H

41 3/4" (1060)

8 15/16" (227)

W

H

5 7/8" (149)

12 7/16" (316)

A

B

1 7/8" (48)

28 3/4" (730)

Cut-Out Location

H

69 9/16" (1767)

W

H

18 3/4" (476)

69 9/16" (1767)

W

H

47 3/4" (1213)

8 15/16" (227)

W

H

5 7/8" (149)

12 7/16" (316)

A

B

1 7/8" (48)

28 3/4" (730)

*For models BI-42SD and BI-48SD, panel thickness in dispenser area can range from 1/4" (6) to 1 1/8" (29) max. If panel is thicker, rout out 1/4" (6) min flat landing area to accommodate dispenser.

WINE

Grille Panel

W

W

28 1/2" (724)

I N T E G R AT E D

MODEL BI-36S

|

23

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

B UILT-IN R EF R IGE RATION

Overlay Panel Dimensions H H

H H H

H H

H H AH A

H H

H H H

A A A

H AH AH H A AH A

H H

H H AH A

H H

W W W W W

I N T E G R AT E D

BI-30U, BI-36U(ID)

H H H

H H

H H H

W

H

36" (914) 35 1/8" (892) 35 3/4" (908)

69 3/4" (1772) 15/16" (1751) 68 H H H H H 69 9/16" (1767)

GRI L L E

Overlay Panel Spacer Panel Backer Panel

W

H

36" (914) A A A 35 1/8" (892) B B 35 3/4" (908)

9 1/4" (235)* 8 5/16" (211) B 8 15/16" (227)

BI-36RG

Stiles | Rails

W W W W W W W W W W

A A B B

A

B

5 1/4" (133)

10 3/8" (264)

W

H

30" (762) 29 1/8" (740) 29 3/4" (756)

50 1/8" (1273) 49 5/16" (1253) 49 15/16" (1268)

W

H

30" (762) 29 1/8" (740) 29 3/4" (756)

19" (483) 18 1/16" (459) 18 11/16" (475)

W W W W W W W W W W

MODEL BI-30U, BI-30UG

WINE

R EF R I G E R AT O R

Overlay Panel Spacer Panel Backer Panel FREEZER

Overlay Panel Spacer Panel Backer Panel GRI L L E

Overlay Panel Spacer Panel Backer Panel

W

H

30" (762) 29 1/8" (740) 29 3/4" (756)

9 1/4" (235)* 8 5/16" (211) 8 15/16" (227)

BI-30UG

Stiles | Rails

24

|

H H

H H H

W W W WWWW W W W

A A A

H H

H H H

H H

H H H

W W W W W

BI-30UG, BI-36UG

W W W W W

BI-36UFD(ID), BI-42UFD(ID)

MODEL BI-36U(ID), BI-36UG

R E F R I G E R AT O R | F RE E Z E R

H H

A AH A H AH AH H

H H H

MODEL BI-36R, BI-36RG, BI-36F

Overlay Panel Spacer Panel Backer Panel

H H H

H H H

W W W W W

BI-36RG

H H

H H

A A A

B B B

W W W W W

BI-36R, BI-36F

UNDERCOUNTER

A A A

A A

B B

H H H

H H A A

PRO 48

H H

H H H

A A A

A A

Sub-Zero Customer Care 800.222.7820

A

5 1/4" (133)

REFRIGERATOR

Overlay Panel Spacer Panel Backer Panel FREEZER

Overlay Panel Spacer Panel Backer Panel GRIL L E

Overlay Panel Spacer Panel Backer Panel

W

H

36" (914) 35 1/8" (892) 35 3/4" (908)

50 1/8" (1273) 49 5/16" (1253) 49 15/16" (1268)

W

H

36" (914) 35 1/8" (892) 35 3/4" (908)

19" (483) 18 1/16" (459) 18 11/16" (475)

W

H

36" (914) 35 1/8" (892) 35 3/4" (908)

9 1/4" (235)* 8 5/16" (211) 8 15/16" (227)

BI-36U G

A

5 1/4" (133)

Stiles | Rails

MODEL BI-36UFD(ID) REFRIGERATOR (2 PAN EL S)

Overlay Panel Spacer Panel Backer Panel FREEZER

Overlay Panel Spacer Panel Backer Panel GRIL L E

Overlay Panel Spacer Panel Backer Panel

W

H

17 7/8" (454) 17" (432) 17 5/8" (448)

50 1/8" (1273) 49 5/16" (1253) 49 15/16" (1268)

W

H

36" (914) 35 1/8" (892) 35 3/4" (908)

19" (483) 18 1/16" (459) 18 11/16" (475)

W

H

36" (914) 35 1/8" (892) 35 3/4" (908)

9 1/4" (235)* 8 5/16" (211) 8 15/16" (227)

B UILT-IN R EF R IGE RATION

WW

AA

HH

HH

B U I L T- I N

HH

WW

BB WW

WW

WW

WW

WW

Overlay Panel Dimensions HH

MODEL BI-42S, BI-42SID, BI-42SD

HH

REFRIGERATOR

HH

Overlay Panel Spacer Panel Backer Panel

HH

W

H

25 1/16" (637) 24 3/16" (614) 24 13/16" (630)

69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767)

FREEZER

AA BB

WW

WW

BI-36S, BI-42S(ID), BI-48S(ID)

WW

W

H

16 11/16" (424) 15 13/16" (402) 16 7/16" (418)

69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767)

GRIL L E

Overlay Panel Spacer Panel Backer Panel

WW

W

H

42" (1067) 41 1/8" (1045) 41 3/4" (1060)

9 1/4" (235)* 8 5/16" (211) 8 15/16" (227)

BI-42SD

BI-42SD, BI-48SD

Dispenser Cut-Out

W

H

5 7/8" (149)

12 7/16" (316)

Cut-Out Location

R E F R I G E R AT O R ( 2 PANE LS)

Overlay Panel Spacer Panel Backer Panel FREEZER

Overlay Panel Spacer Panel Backer Panel GRI L L E

Overlay Panel Spacer Panel Backer Panel

MODEL BI-48S, BI-48SID, BI-48SD W

H

20 7/8" (530) 20" (508) 20 5/8" (524)

50 1/8" (1273) 49 5/16" (1253) 49 15/16" (1268)

W

H

42" (1067) 41 1/8" (1045) 41 3/4" (1060)

19" (483) 18 1/16" (459) 18 11/16" (475)

W

H

42" (1067) 41 1/8" (1045) 41 3/4" (1060)

9 1/4" (235)* 8 5/16" (211) 8 15/16" (227)

REFRIGERATOR

Overlay Panel Spacer Panel Backer Panel FREEZER

Overlay Panel Spacer Panel Backer Panel GRIL L E

Overlay Panel Spacer Panel Backer Panel BI-48SD

Dispenser Cut-Out

Overlay Panel Spacer Panel Backer Panel FREEZER

Overlay Panel Spacer Panel Backer Panel GRI L L E

H

20 1/16" (510) 19 3/16" (487) 19 13/16" (503)

69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767)

W

H

15 11/16" (398) 14 13/16" (376) 15 7/16" (392)

69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767)

W

H

36" (914) 35 1/8" (892) 35 3/4" (908)

9 1/4" (235)* 8 5/16" (211) 8 15/16" (227)

Cut-Out Location

H

69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767)

W

H

19" (483) 18 1/8" (460) 18 3/4" (476)

69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767)

W

H

48" (1219) 47 1/8" (1197) 47 3/4" (1213)

9 1/4" (235)* 8 5/16" (211) 8 15/16" (227)

W

H

5 7/8" (149)

12 7/16" (316)

A

B

2" (51)

28 13/16" (732)

*Panel height may be increased by 7/16" (11) to hide upper main frame. Also refer to built-in panel configurator at subzero.com/trade/panels. Grille panel dimensions are for standard 84" (2134) overall unit height. For 83" (2108) height, subtract 1" (25) from grille panel height dimensions and for 88" (2235) height, add 4" (102). A specific panel grille must be ordered for an 83" or 88" overall unit height.

subzero.com/specs

|

25

UNDERCOUNTER

Overlay Panel Spacer Panel Backer Panel

W

W

28 3/4" (730) 27 7/8" (708) 28 1/2" (724)

WINE

MODEL BI-36S R EF R I G E R AT O R

B

28 13/16" (732)

I N T E G R AT E D

MODEL BI-42UFD(ID)

A

2" (51)

PRO 48

Overlay Panel Spacer Panel Backer Panel

B U I L T- I N

B UILT-IN R EF R IGE RATION

Flush Inset Panel Dimensions H H

H H H

H H

H H AH A

H H

H H H

A A A

H AH AH H A AH A

H H

H H AH A

H H

W W W W W

I N T E G R AT E D

BI-30U, BI-36U(ID)

H H H

H H

H H H

WINE

BI-30UG, BI-36UG

W W W W W

BI-36UFD(ID), BI-42UFD(ID)

W

H

50 1/8" (1273) 49 5/16" (1253) 49 15/16" (1268)

W

H

37" (940) A A A 35 1/8" (892) B B 35 3/4" (908)

9 1/4" (235) 8 5/16" (211) B 8 15/16" (227)

A A B B

R EF R I G E R AT O R

W

H

Flush Inset Panel Spacer Panel Backer Panel

31" (787) 29 1/8" (740) 29 3/4" (756)

50 1/8" (1273) 49 5/16" (1253) 49 15/16" (1268)

W

H

31" (787) 29 1/8" (740) 29 3/4" (756)

19" (483) 18 1/16" (459) 18 11/16" (475)

W W W W W W W W W W

FREEZER

GRI L L E

W

H

31" (787) 29 1/8" (740) 29 3/4" (756)

9 1/4" (235) 8 5/16" (211) 8 15/16" (227)

BI-30UG

|

W W W W W

37" (940) 35 1/8" (892) 35 3/4" (908)

MODEL BI-30U, BI-30UG

26

H H H

Flush Inset Panel Spacer Panel Backer Panel

B

Stiles | Rails

H H

REFRIGERATOR

10 3/8" (264)

Flush Inset Panel Spacer Panel Backer Panel

H H H

69 3/4" (1772) 15/16" (1751) 68 H H H H H 69 9/16" (1767)

A

Flush Inset Panel Spacer Panel Backer Panel

H H

37" (940) 35 1/8" (892) 35 3/4" (908)

5 3/4" (146)

W W W W W W W W W W

W W W WWWW W W W

B B B

H

BI-36RG

Stiles | Rails

H H H

W

GRI L L E

Flush Inset Panel Spacer Panel Backer Panel

H H

MODEL BI-36U(ID), BI-36UG

R E F R I G E R AT O R | F RE E Z E R

H H

H AH AH H A AH A

H H H

MODEL BI-36R, BI-36RG, BI-36F

Flush Inset Panel Spacer Panel Backer Panel

H H H

H H H

W W W W W

BI-36RG

H H

H H

B B B

B B B

W W W W W

BI-36R, BI-36F

UNDERCOUNTER

A A A

B A

B B

H H H

H H B A

PRO 48

H H

H H H

A A A

A A

A

B

5 3/4" (146)

5 1/4" (133)

Sub-Zero Customer Care 800.222.7820

FREEZER

Flush Inset Panel Spacer Panel Backer Panel GRIL L E

Flush Inset Panel Spacer Panel Backer Panel BI-36U G

Stiles | Rails

W

H

37" (940) 35 1/8" (892) 35 3/4" (908)

19" (483) 18 1/16" (459) 18 11/16" (475)

W

H

37" (940) 35 1/8" (892) 35 3/4" (908)

9 1/4" (235) 8 5/16" (211) 8 15/16" (227)

A

B

5 3/4" (146)

5 1/4" (133)

MODEL BI-36UFD(ID) REFRIGERATOR (2 PAN EL S)

Flush Inset Panel Spacer Panel Backer Panel FREEZER

Flush Inset Panel Spacer Panel Backer Panel GRIL L E

Flush Inset Panel Spacer Panel Backer Panel

W

H

18 3/8" (467) 17" (432) 17 5/8" (448)

50 1/8" (1273) 49 5/16" (1253) 49 15/16" (1268)

W

H

37" (940) 35 1/8" (892) 35 3/4" (908)

19" (483) 18 1/16" (459) 18 11/16" (475)

W

H

37" (940) 35 1/8" (892) 35 3/4" (908)

9 1/4" (235) 8 5/16" (211) 8 15/16" (227)

B UILT-IN R EF R IGE RATION

WW

AA

HH

HH

B U I L T- I N

HH

WW

BB WW

WW

WW

WW

WW

Flush Inset Panel Dimensions HH

MODEL BI-42S, BI-42SID, BI-42SD

HH

HH

HH

REFRIGERATOR

W

H

Flush Inset Panel Spacer Panel Backer Panel

25 9/16" (649) 24 3/16" (614) 24 13/16" (630)

69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767)

FREEZER

AA BB

WW

WW

BI-36S, BI-42S(ID), BI-48S(ID)

WW

W

H

17 3/16" (437) 15 13/16" (402) 16 7/16" (418)

69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767)

GRIL L E

Flush Inset Panel Spacer Panel Backer Panel

WW

W

H

43" (1092) 41 1/8" (1045) 41 3/4" (1060)

9 1/4" (235) 8 5/16" (211) 8 15/16" (227)

BI-42SD

BI-42SD, BI-48SD

Dispenser Cut-Out

W

H

5 7/8" (149)

12 7/16" (316)

Cut-Out Location

R E F R I G E R AT O R ( 2 PANE LS)

Flush Inset Panel Spacer Panel Backer Panel FREEZER

Flush Inset Panel Spacer Panel Backer Panel GRI L L E

Flush Inset Panel Spacer Panel Backer Panel

MODEL BI-48S, BI-48SID, BI-48SD W

H

REFRIGERATOR

W

H

21 3/8" (543) 20" (508) 20 5/8" (524)

50 1/8" (1273) 49 5/16" (1253) 49 15/16" (1268)

Flush Inset Panel Spacer Panel Backer Panel

29 1/4" (743) 27 7/8" (708) 28 1/2" (724)

69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767)

W

H

43" (1092) 41 1/8" (1045) 41 3/4" (1060)

19" (483) 18 1/16" (459) 18 11/16" (475)

W

H

43" (1092) 41 1/8" (1045) 41 3/4" (1060)

9 1/4" (235) 8 5/16" (211) 8 15/16" (227)

FREEZER

Flush Inset Panel Spacer Panel Backer Panel GRIL L E

Flush Inset Panel Spacer Panel Backer Panel BI-48SD

Dispenser Cut-Out

R E F R I G E R AT O R

W

H

Flush Inset Panel Spacer Panel Backer Panel

20 9/16" (522) 19 3/16" (487) 19 13/16" (503)

69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767)

FREEZER

GRI L L E

H

69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767)

W

H

37" (940) 35 1/8" (892) 35 3/4" (908)

9 1/4" (235) 8 5/16" (211) 8 15/16" (227)

H

69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767)

W

H

49" (1245) 47 1/8" (1197) 47 3/4" (1213)

9 1/4" (235) 8 5/16" (211) 8 15/16" (227)

W

H

5 7/8" (149)

12 7/16" (316)

A

B

2" (51)

28 13/16" (732)

Grille panel dimensions are for standard 84" (2134) overall unit height. For 83" (2108) height, subtract 1" (25) from grille panel height dimensions and for 88" (2235) height, add 4" (102). A specific panel grille must be ordered for an 83" or 88" overall unit height.

subzero.com/specs

|

27

UNDERCOUNTER

Flush Inset Panel Spacer Panel Backer Panel

W

16 3/16" (411) 14 13/16" (376) 15 7/16" (392)

Cut-Out Location

W

19 1/2" (495) 18 1/8" (460) 18 3/4" (476)

WINE

MODEL BI-36S

Flush Inset Panel Spacer Panel Backer Panel

B

28 13/16" (732)

I N T E G R AT E D

MODEL BI-42UFD(ID)

A

2" (51)

PRO 48

Flush Inset Panel Spacer Panel Backer Panel

B UILT-IN R EF R IGE RATION

TOP VIEW

TOP VIEW

B U I L T- I N

BACKER CABINETRY SPACER

BACKER SPACER

PANEL O F F S ET

5/16" (8) BACKER SPACER

PRO 48

IL L U S

Door (hinge) | Drawer | Grille Sides Doors (handle) Sides (French door only) Grille Top Grille Bottom | Door Top Door Bottom | Drawer Top Drawer Bottom SI D E - B Y- S I D E

Doors (hinge) | Grille Sides Doors (handle) Sides Grille Top Grille Bottom | Door Top Door Bottom

5/16A " (8)

A B GRILLE C CABINETRY D E F IL L U S

GRILLE

A B C D F

CABINETRY

GRILLE

1/2" (13)

CABINETRY

5/8" (16)

5/8" (16)

5/16" (8)

1/2" (13)

CABINETRY

1/2" (13)

5/8" (16)

1/2" (13)

1/8" 5/16" (3) GRILLE (8)

CABINETRY

1/2" (13)

1/8"

5/16VIEW SIDE " (3)GRILLE (8)

CABINETRY

1/2" (13)

1/8" 5/16 " (3) GRILLE SIDE VIEW (8)

WINE

5/16" 5/32 3/DRAWER (8) "32" 5/16" (4)(2) (8) DOOR

/8" (16)

5/16" DRAWER 35//32 (8) Illus. 32"E " 5/16" (2) (4) (8) DOOR

UNDERCOUNTER

5/8" (16) SIDE VIEW

DRAWER

5/DRAWER 32" 5/16" (4) (8) SIDE VIEW

28

|

Sub-Zero Customer Care 800.222.7820

5/16" (8)

5/16" (8)

DOOR 1/8" (3)

DOOR DOOR 1/8" (3)

DOOR

1/4" (6)

1/4" (6)

REVEAL

5/16" (8)

5/16" (8)

1/8" (3)

1/8" (3) 1/4" (6)

REVEAL

1/2" (13)

5/16" DOOR 3/32 5/"32GRILLE " 5/16(8) " (2)(4) (8)

DOOR GRILLE

5/16" 35/32" /32" 5/(8) 16" (2) (4) (8)

SIDE VIEW

SIDE VIEW

1/2" (13)

1/2

5/16" DOOR GRILLE 32 (8) 53//32 "" 5/16" (4) (2) (8)

DOOR GRILLE

1/8" 5/16 " (3) SIDE VIEW (8)

5/16" 32"" (8) 53//32 5/16" (4) (2) (8)

SIDE VIEW

SIDE VIEW

1/2" (13)

Illus.DOOR D

SIDE VIEW

1/2

1/2" (13)

1/8" 5SIDE VIEW /16" (3) (8) 1/2" (13)

5/16" (8) 5/32" (4)

5/16" (8) 5/32" GRILLE (4)

GRILLE

1/8" 5/16" (3) (8) 1/2" (13)

REVEAL

1/2

DOOR

3/32" 5/16" (2) (8)

SIDE VIEW

DOOR / DRAWER

3/32" 5/16" (2) (8)

DOOR / DRAWER

SIDE VIEW

DOOR

SIDE VIEW 5

DOOR

TOP VIEW REVEAL

5/16" (8) 3/32" (2)

5/8" (16)

DRAWER

TOP VIEWREVEAL

Illus. B

SIDE VIEW

DOOR

DOOR

1/4" (6)

1/4" (6)

1/4" (6)

Illus. A

5/16" (8) 3/32" (2)

DRAWER

1/8" (3) DOOR DOOR

1/8DOOR " (3)

REVEAL

Illus. C

DOOR

5/16" (8)

5/16" (8)

FLUSH INSET PANEL

IL L U S

OV E R - A N D - U N D E R

5/CABINETRY 8" (16)

5/16" (8)

BACKER CABINETRY

FLUSH INSET PANEL

C D CABINETRY F

1/2" (13)

TOP VIEW

5/8" SPACER (16)

Door | Grille Sides Grille Top Grille Bottom | Door Top Door Bottom

TOP VIEW

DOOR / DRAWER / GRILLE FLUSH INSET PANEL

1/2" (13)

PANEL OFFSET A L L R E F R I G E R AT O R | ALL FREE Z E R

5/16" (8)

BACKER 5/8"CABINETRY SPACER TOP VIEW (16)

BACKER SPACER

TOP VIEW

DOOR

DOOR / DRAWER / GRILLE FLUSH INSET PANEL

1/2" (13)

The illustrations provide panel offsets and reveals for built-in models in a flush inset application. Refer to the chart below 5/16" (8) for reference to the illustrations.

DOOR DOOR

DOOR

TOP VIEW

DOOR / DRAWER / GRILLE FLUSH INSET PANEL

I N T E G R AT E D

CABINETRY

TOP VIEW DOOR / DRAWER / GRILLE FLUSH INSET PANEL

Flush Inset Panels

TOP VIEW

TOP VIEW

DOOR / DRAWER / GRILLE

DOOR / DRAWER / GRILLE

5/8" (16)

DOOR / DRAWER

5/16" (8)

DOOR / DRAWER

5/16" (8)

5/16" (8) 53/32" 5/16" (4) (2) (8) SIDE VIEW 5

SIDE VIEW DOOR / DRAWER

/8" (16)

5/16" (8) 35//32 32"" 5/16" (2) (4) (8) 5/8" (16) SIDE VIEW

5/32" (4) SIDE VIEW 5/16" DOOR / (8) DRAWER

5

5/16" (8)

Illus. F

SIDE VIEW

5/32" 5/16" (4) (8)

5 SIDE VIEW

5/16" (8)

5/32" 5/16" (4) (8) SIDE VIEW

SIDE VIEW

5/32" (4)

5 SIDE VIEW

B UILT-IN R EF R IGE RATION

B U I L T- I N

Dual Installation For dual standard installations, panel dimensions are the same as for single installations. Refer to the charts on pages 22–25. Panel dimensions and offsets for dual flush inset installations are listed on the following pages.

PRO 48

If two units are installed side by side, a dual installation kit may be required. Installations without a custom filler strip require a dual installation kit. If a dual installation kit is not specified, a 2" (51) filler strip is recommended between units. A custom filler strip is required when installing two French door or side-by-side models. Dual installations without a filler strip can only be accomplished using two units with opposite hinges. Refer to the illustrations below. Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero customer care at 800-222-7820.

I N T E G R AT E D

WITHOUT FILLER STRIP

Opposite hinges.

FILLER STRIP

Same side hinges.

WINE

|

29

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

B UILT-IN R EF R IGE RATION

Dual Flush Inset Panel Dimensions H H

H H

H H

H H

H H

H H A AH AH A

A AH H

H H

W W

W W

BI-36R, BI-36F

B B

H H

W W

W W

BI-36RG

I N T E G R AT E D

W W

W W

W W

W

H

36 1/2" (927) 35 1/8" (892) 35 3/4" (908)

50 1/8" (1273) 49 5/16" (1253) 49 15/16" (1268)

W

H

36 1/A2" A(927) 35 1/8" (892) B B 35 3/4" (908)

9 1/4"A(235) A 8 5/16" (211) B 8 15/16" (227)

W W WW

A

B

5 3/4" (146)

10 3/8" (264)

W W

W W

30 1/2" (775) 29 1/8" (740) 29 3/4" (756)

50 1/8" (1273) 49 5/16" (1253) 49 15/16" (1268)

FREEZER

W

H

30 1/2" (775) 29 1/8" (740) 29 3/4" (756)

19" (483) 18 1/16" (459) 18 11/16" (475)

GRI L L E

W

H

30 1/2" (775) 29 1/8" (740) 29 3/4" (756)

9 1/4" (235) 8 5/16" (211) 8 15/16" (227)

BI-30UG

A

B

5 3/4" (146)

5 1/4" (133)

Sub-Zero Customer Care 800.222.7820

FREEZER

B

W W

Flush Inset Panel Spacer Panel Backer Panel

|

BI-30UG, BI-36UG

Flush Inset Panel Spacer Panel H H Backer Panel

H

30

W W

W W

REFRIGERATOR

W

Stiles | Rails

H H

H H

69 3/4" (1772) 15/16" (1751) 68 H H 69 9/16" (1767)

R EF R I G E R AT O R

Flush Inset Panel Spacer Panel Backer Panel

W W

36 1/2" (927) 35 1/H8" H(892) 35 3/4" (908)

MODEL BI-30U, BI-30UG

Flush Inset Panel Spacer Panel Backer Panel

W W

W W

W W

H

BI-36RG

Stiles | Rails

H H

W

GRI L L E

Flush Inset Panel Spacer Panel Backer Panel

H H

MODEL BI-36U(ID), BI-36UG

R E F R I G E R AT O R | F RE E Z E R

H H

A AH H

H H

H H

MODEL BI-36R, BI-36RG, BI-36F

Flush Inset Panel Spacer Panel Backer Panel

H H

H H

H H

W W

BI-30U, BI-36U(ID)

H H

H H

WINE

W W

W W

H H

W W B B

B A

B B

H H B B

H H A AH AH A

A A

H H

UNDERCOUNTER

H H

B A

PRO 48

A A

H H

H H

A A

A A

Flush Inset Panel Spacer Panel Backer Panel GRIL L E

Flush Inset Panel Spacer Panel Backer Panel BI-36U G

Stiles | Rails

W

H

36 1/2" (927) 35 1/8" (892) 35 3/4" (908)

19" (483) 18 1/16" (459) 18 11/16" (475)

W

H

36 1/2" (927) 35 1/8" (892) 35 3/4" (908)

9 1/4" (235) 8 5/16" (211) 8 15/16" (227)

A

B

5 3/4" (146)

5 1/4" (133)

Grille panel dimensions are for standard 84" (2134) overall unit height. For 83" (2108) height, subtract 1" (25) from grille panel height dimensions and for 88" (2235) height, add 4" (102). A specific panel grille must be ordered for an 83" or 88" overall unit height. For dual wide grilles, refer to page 32.

B UILT-IN R EF R IGE RATION

TOP VIEW

TOP VIEW

CABINETRY

TOP VIEW

Dual Installation D U AL F LUS H IN SE T PANE L OFFSE T

BACKER 5/8"CABINETRY (16) SPACER

IL L U S

Door (hinge) | Grille Sides Door (handle) Sides Grille Top Grille Bottom | Door Top Door Bottom

A B C CABINETRY D F

OV E R - A N D - U N D E R

IL L U S

TOP VIEW

GRILLE

5/CABINETRY 8" (16)

5/16" (8)

1/2" (13)

BACKER

1/2" (13)

CABINETRY

5/8" (16)

5/16" (8)

CABINETRY

1/2" (13)

5/8" (16)

1/2" (13)

5/16" (8)

5/16" (8)

DOOR 1/8" (3)

DOOR DOOR 1 /8" (3)

DOOR

1/4" (6)

1/4" (6)

REVEAL

1/8" (3)

1/8" (3)

CABINETRY

1/2" (13)

1/8"

5/16VIEW SIDE " (3)GRILLE CABINETRY

1/4" (6)

REVEAL

REVEAL

1/2" (13)

1/8" 5/16" (3) (8) 1/2" (13)

1/2

1/2" (13) 5/16" DOOR 3/32 5/"32GRILLE " 5/16(8) " (2)(4) (8)

DOOR GRILLE

1/8" 5SIDE VIEW /16" (3) (8)

5/16" 35/32" /32" 5/(8) 16" (2) (4) (8)

SIDE VIEW

SIDE VIEW

1/2" (13)

DOOR

1/2

5/16" 32"" (8) 53//32 5/16" (4) (2) (8)

DOOR

3/32 GRILLE " 5/16" (2) (8)

1/8" 5/16 " (3) SIDE VIEW (8)

SIDE VIEW

SIDE VIEW

1/2

DOOR

Illus. D

SIDE VIEW

5/16" (8) 5/32" (4)

5/16" (8) 5/32" GRILLE (4)

GRILLE

Illus. B

1/8" 5/16" (3) GRILLE (8)

(8)

5/16" (8)

5/16" (8)

1/4" (6)

Illus. A

3/32" 5/16" (2) (8)

DOOR / DRAWER

DOOR / DRAWER

SIDE VIEW

5/16" (8) 3/32" (2)

5/16" (8) 3/32" (2) DOOR

5/16" 5/32 3/DRAWER (8) "32" 5/16" (4)(2) (8) DOOR SIDE VIEW 5

/8" (16)

5/DRAWER Illus. 32E " 5/16" (4) (8) DOOR SIDE VIEW

DOOR / DRAWER

5/16" (8)

DOOR / DRAWER

5/16" (8) 53/32" 5/16" (4) (2) (8) SIDE VIEW 5

SIDE VIEW

/8" (16)

5/16" (8) 35//32 32"" 5/16" (2) (4) (8) 5/8" (16) SIDE VIEW

5/32" (4) SIDE VIEW 5/16" DOOR / (8) DRAWER

5/16" (8)

5

5/16" (8)

Illus. F

SIDE VIEW

5/32" (4)

5 SIDE VIEW

5/32" 5/16" (4) (8) SIDE VIEW

SIDE VIEW

subzero.com/specs

|

31

5/16" (8)

UNDERCOUNTER

DRAWER

5/8" (16)

WINE

5/8" (16)

DRAWER

TOP VIEW REVEAL

TOP VIEWREVEAL

REVEAL

Illus. C

DOOR

DOOR

1/4" (6)

1/4" (6)

FLUSH INSET PANEL

GRILLE SIDE VIEW

DRAWER

1/8" (3) DOOR DOOR

1/8DOOR " (3)

DUAL TRIM

1/2" (13)

DOOR

5/16" (8)

5/16" (8)

I N T E G R AT E D

A B CABINETRY C D E F

GRILLE

TOP VIEW

PRO 48

A L L R E F R I G E R AT O R | ALL FREE Z E R

1/2" (13)

DOOR / DRAWER / GRILLE FLUSH INSET PANEL

5/8" SPACER (16)

PANEL OFFSET

Door (hinge) | Drawer | Grille Sides Door (handle) Sides Grille Top Grille Bottom | Door Top Door Bottom | Drawer Top Drawer Bottom

5/16" (8)

1/2" (13)

The illustrations provide panel offsets and reveals for built-in FLUSH INSET PANEL models in a dual flush inset application. Refer to the chart 5/16" (8) below for reference to the illustrations.

TOP VIEW

DOOR

DOOR / DRAWER / GRILLE FLUSH INSET PANEL

5/16" (8) BACKER SPACER

DOOR DOOR

DOOR

TOP VIEW

DOOR / DRAWER / GRILLE FLUSH INSET PANEL

B U I L T- I N

BACKER CABINETRY SPACER

BACKER SPACER

TOP VIEW

TOP VIEW

DOOR / DRAWER / GRILLE

DOOR / DRAWER / GRILLE

5

B U I L T- I N

B UILT-IN R EF R IGE RATION

Dual Installation D U AL WIDE G R IL L E

DUAL WIDE GRILLE—FLUSH INSET

PRO 48

A dual wide grille spans the entire width of both units in a dual installation and is a part of a dual installation kit. For overlay and flush inset panel dimensions for the dual wide grille, refer to the charts below. Dimensions listed are for a standard 84" (2134) finished height. DUAL WIDE GRILLE—OVERLAY T WO 3 0 " M O D E L S

Overlay Panel Spacer Panel Backer Panel

W

H

60 1/4" (1530) 59 3/8" (1508) 60" (1524)

9 1/4" (235) 8 5/16" (211) 8 15/16" (227)

30" A N D 3 6 " M O D E L

Overlay Panel Spacer Panel Backer Panel

W

H

66 1/4" (1683) 65 3/8" (1661) 66" (1676)

9 1/4" (235) 8 5/16" (211) 8 15/16" (227)

Overlay Panel Spacer Panel Backer Panel

W

H

72 1/4" (1835) 71 3/8" (1813) 72" (1829)

9 1/4" (235) 8 5/16" (211) 8 15/16" (227)

WINE

I N T E G R AT E D

T WO 3 6 " M O D E L S

UNDERCOUNTER

TWO 30" MOD EL S

32

|

Sub-Zero Customer Care 800.222.7820

Flush Inset Panel Spacer Panel Backer Panel 30" AN D 36" MOD EL

Flush Inset Panel Spacer Panel Backer Panel TWO 36" MOD EL S

Flush Inset Panel Spacer Panel Backer Panel

W

H

61 1/4" (1556) 59 3/8" (1508) 60" (1524)

9 1/4" (235) 8 5/16" (211) 8 15/16" (227)

W

H

67 1/4" (1708) 65 3/8" (1661) 66" (1676)

9 1/4" (235) 8 5/16" (211) 8 15/16" (227)

W

H

73 1/4" (1861) 71 3/8" (1813) 72" (1829)

9 1/4" (235) 8 5/16" (211) 8 15/16" (227)

B UILT-IN R EF R IGE RATION

B U I L T- I N

Standard Handles

The custom side panels must be a minimum of 24" (610) deep and 1/2" (13) thick. Routing will be necessary for the side panel to fit flush against the side of the unit. Refer to the illustrations below.

Optional stainless steel tubular and pro handles are avail­ able through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com.

When installing a built-in unit with a custom side panel, an accessory kit is required. Stainless steel and white enamel side panels are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com.

Refer to the chart below for standard handle lengths for built-in models.

24" (610) FRONT OF SIDE PANEL

HANDLE LENGTH

TU BU L A R

PRO

Full Door

63 7/8"

Over-and-Under Door

44 1/4"

30" Drawer

24 5/16" (633)

17 9/16" (447)

36" Drawer

30 5/16" (770)

23 5/8" (600)

42" Drawer

36 5/16" (922)

29 5/8" (753)

(1622) (1124)

45 3/16"

(1147)

37 1/2"

PRO 48

Side Panel

(952)

1" (25) 1 7/8" (48)

I N T E G R AT E D

1/8" (3) 1/2" (13)

ROUT TO 1/8" (3)

1 7/8"(48) 84"

1" (25)

MAIN FRAME

SIDE PANEL ROUTING

(2134)

Routing detail. 4 1/4" (108) ROUT TO 3/16" (5) (OVER-AND-UNDER MODELS)

5 3/4" (146)

20 1/2" (521)

WINE

4" (102) OPTIONAL TOE KICK CUT-OUT

2 5/8" (67)

Side panel dimensions.

|

33

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

B UILT-IN R EF R IGE RATION

Framed Panels

PRO 48

F ULL-S CALE T E MPL ATE

OPTIONAL EXTENDED FULL-LENGTH HANDLE

I N T E G R AT E D

STANDARD FULL-LENGTH HANDLE

2"

1"

(51)

(25)

3"

(76)

11/4" (32) PANEL 1" (25) PANEL 3/4" (19) PANEL 1/2" (13) PANEL

WINE

1/4" (6) FRAMED PANEL

DOOR

UNDERCOUNTER

Framed panel thickness.

34

|

Sub-Zero Customer Care 800.222.7820

B UILT-IN R EF R IGE RATION

B U I L T- I N

Overlay | Flush Inset Panels F ULL-S CALE T E MPL ATE

Overlay and flush inset panels must be a minimum of 5/8" (16) thick to support mounting the handle. Panel thickness does not include backer and spacer panel. Mount handle close to the opening edge of the door. PRO 48

DEPTH OF TUBULAR AND PRO HANDLES

2"

(51)

3"

I N T E G R AT E D

1"

(25)

(76)

11/4" (32) PANEL 1" (25) PANEL 3/4" (19) PANEL

.10" (3) SPACER PANEL 1/4" (6) BACKER PANEL

WINE

DOOR

Overlay and flush inset panel thickness.

|

35

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

B UILT-IN R EF R IGE RATION

Overlay Application F ULL-S CALE T E MPL ATE 237/8" (606) TO REAR OF UNIT

OVERALL WIDTH OF UNIT

PRO 48

0" (0) 1/4" (6) 1/2" (13) 3/4" (19)

1" (25) 11/4" (32) 11/2" (38) 13/4" (44) I N T E G R AT E D

2" (51) 21/4" (57) 21/2" (63) 23/4" (70) 3" (76) 31/4" (83) 31/2" (89)

WINE

1" (25) THICK PANEL

3/4" (19) THICK OVERLAY PANEL (TYPICAL)

UNDERCOUNTER

1/4" (6) BACKER

PANEL

0"

1" (25) SCALE

90° door opening (top view).

36

|

Sub-Zero Customer Care 800.222.7820

B UILT-IN R EF R IGE RATION

B U I L T- I N

Flush Inset Application F ULL-S CALE T E MPL ATE

24" (610) TO BACK WALL

For panels thicker than 3/4" (19), a 90° door stop may be required to prevent interference with adjacent cabinets. 1 1/4" (32) PRO 48

2 3/16" (56) ASSUMES 3/4" (19) FLUSH INSET PANEL THICKNESS

I N T E G R AT E D WINE

1" (25) THICK PANEL

3/4" (19) THICK FLUSH INSET PANEL (TYPICAL)

1/4" (6) BACKER

0"

1" (25) SCALE

110° door opening (top view).

subzero.com/specs

|

37

UNDERCOUNTER

PANEL

B U I L T- I N

B UILT-IN R EF R IGE RATION

PRO 48

FILLER STRIP

11/4" (32)

WINE

I N T E G R AT E D

APPROX PROFILE OF STAINLESS STEEL WRAPPED DOOR AND HANDLE

Dual Standard Installation F ULL-S CALE T E MPL ATE

UNDERCOUNTER

Typical framed, overlay or stainless steel dual installation with filler strip at maximum 110° door opening. Panel thickness may require a 90° door stop.

0"

1" (25) SCALE

Dual standard installation (top view).

38

|

Sub-Zero Customer Care 800.222.7820

DOOR CLOSED

DOOR OPEN 110°

B UILT-IN R EF R IGE RATION

B U I L T- I N

FILLER STRIP

PRO 48

1 1/2" (38)

1/2" (13)

WINE

Dual Flush Inset Installation

DOOR CLOSED

I N T E G R AT E D

PROFILE OF 3/4" (19) FLUSH INSET PANEL AND TUBULAR HANDLE

DOOR OPEN 110°

F ULL-S CALE T E MPL ATE

Typical flush inset dual installation with filler strip at maximum 110° door opening. Panel thickness may require a 90° door stop.

1" (25) SCALE

Dual flush inset installation (top view).

subzero.com/specs

|

39

UNDERCOUNTER

0"

P RO 48 R EF R IGE RATION

B U I L T- I N

PRO 48 Refrigeration P R O 4 8 MO D ELS

PRO 48

Freshness finds unmistakable expression in the Sub-Zero PRO 48. An 800-pound monument to food preservation— equal parts sculpted metal design statement and culinary secret weapon. Its vast interior, like its bold exterior, is crafted of stainless steel. The PRO 48 is available with or without a glass door and may be either built in or freestanding.

648PRO

648PROG

I N T E G R AT E D WINE

|

41

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

P RO 48 R EF R IGE RATION

Overall Dimensions P RO 48 25 7/8" (657)

PRO 48

48" (1219)

84"

(2134)

42 1/8" (1070)

30 1/2"

I N T E G R AT E D

(775)

4" (102) HEIGHT DIMENSIONS ± 1/2" (13)

30 3/16" (767)

23 7/8" (606)

14 1/2" (368)

21"

(533)

30 3/4"

WINE

(781)

2 3/8" (60)

Model 648PRO, 648PROG.

SPECIFICATIONS IN TERIOR C APAC ITY

648PRO 648PROG

UNDERCOUNTER

SH IPP IN G WEIGH T

648PRO 648PROG

42

|

Sub-Zero Customer Care 800.222.7820

R C U FT (L)

F CU FT (L)

18.4 (521) 18.4 (521)

11.7 (331) 11.7 (331) LB ( K G )

860 (390) 875 (397)

P RO 48 R EF R IGE RATION

B U I L T- I N

Opening Dimensions S TANDAR D | F LU SH INSTAL L ATION

D

3/4" (19)

OPENING DEPTH

TYPICAL

3 1/2" (89)

TOP VIEW

PRO 48

FINISHED RETURN

W FRAMELESS CABINETRY

3/4" (19) TYPICAL

3 1/2" (89) FINISHED RETURN

W OPENING WIDTH

I N T E G R AT E D

H OPENING HEIGHT

FILLER

W FRAMED CABINETRY

SIDE VIEW

FRONT VIEW

WINE

NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry.

OPENING DIMENSIONS

Standard Flush

W

H

D

47 1/2" (1206) 48" (1219)

83 3/4" (2127) 84 1/8" (2137)

24" (610) 26" (660)

For standard built-in installations, the face frame of the unit will extend 2" (51) beyond cabinetry. For flush installations, the front of the face frame will be flush with surrounding cabinetry.

|

43

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

P RO 48 R EF R IGE RATION

Electrical

Plumbing

The electrical supply should be located within the shaded area shown in the illustration below. A separate circuit servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

The water supply line should be located within the shaded area shown in the illustration below. The water supply line should be connected to the house supply with an easily accessible shut-off valve. Do not use self‑piercing valves. The water supply line must not interfere with installation of the anti-tip bracket.

PRO 48

Installation must comply with all applicable electrical codes. ELECTRICAL REQUIREMENTS

Electrical Supply

115 VAC, 60 Hz

Service

15 amp dedicated circuit

Receptacle

3-prong grounding-type

A reverse osmosis system can be used provided there is constant water pressure of 35–120 psi (2.4–8.3 bar) supplied to the unit at all times. A copper line is not recommended for this application. Installation must comply with all applicable plumbing codes. PLUMBING REQUIREMENTS 1/4"

Water Supply Pressure 7"

E

I N T E G R AT E D

(178)

35–120 psi (2.4–8.3 bar)

Excess Line for Connection

6"

(152)

75 1/2" (1918) FROM FLOOR RIGHT SIDE OF OPENING

RIGHT SIDE OF OPENING

Electrical supply location.

6"

(152)

5 3/16" (132)

3" (76)

UNDERCOUNTER

WINE

AREA EXTENDS 1/2" (13) FORWARD ON FLOOR

Water supply location.

44

|

Sub-Zero Customer Care 800.222.7820

OD copper, braided stainless steel or PEX tubing 36" (914)

P RO 48 R EF R IGE RATION

B U I L T- I N

Standard Handles Optional stainless steel tubular and pro handles are avail­ able through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. Refer to the chart below for standard handle lengths for PRO 48 models. TUBULAR

PRO

NA

27 11/16"

(703)

Refrigerator Drawer

NA

19 15/16"

(506)

Freezer Drawer

NA

Door

PRO 48

HANDLE LENGTH

11 9/16" (294)

I N T E G R AT E D WINE

|

45

UNDERCOUNTER

subzero.com/specs

I N T EG R AT ED R E FRIGE RATION

B U I L T- I N

Integrated Refrigeration With custom front panels and hardware, Sub-Zero integrated columns, tall and drawer models disappear into the decor. Integrated units fit flush with cabinetry, making integrated refrigeration as practical and beautiful in the master suite, bar or theatre room as in the kitchen. Model ID-24RO, approved for outdoor installations, is ideal for any outdoor kitchen. PRO 48

C OLUMN MO DEL S

IC-24R IC-24FI IC-24C(I)

IC-30R(ID) IC-30FI

I N T E G R AT E D

IC-18FI

IC-36R(ID) IC-36FI

TALL MO DELS

WINE

IT-30R(ID) IT-30FI IT-30CI(ID)

IT-36R(ID) IT-36CI(ID)

D RAWER MO DEL S

ID-27R

ID-30R(P) ID-30F(I) ID-30C(I)

ID-36R(P) ID-36C(I)

subzero.com/specs

|

47

UNDERCOUNTER

ID-24R ID-24F(I) ID-24RO

B U I L T- I N

I N T EG R AT ED R E FRIGE RATION

Specifications INTERIOR CAPACITY— CU FT

PRO 48

CO L U M N

IC-18FI IC-24R IC-24FI IC-24C(I) IC-30R(ID) IC-30FI IC-36R(ID) IC-36FI TA L L

C O LU MN

(L )

RE FR

FRZR

8.4 (238)

W

12.9 (365) 8.0 (227) 17.3 (490)

24" (610) 4 1/2" (114)

12.3 (348) 3.1 (88) 15.3 (433)

21.4 (606) 20.0 (566) RE FR

IT-30R(ID) IT-30FI IT-30CI(ID) IT-36R(ID) IT-36CI(ID)

I N T E G R AT E D

Overall Dimensions

69 1/2"

84"*

(2134)

(1765)

FRZR

16.5 (467) 10.6 (300) 20.5 (580) 13.3 (377)

DRAWE R

RE FR

ID-24R ID-24F(I) ID-24RO ID-27R ID-30R(P) ID-30F(I) ID-30C(I) ID-36R(P) ID-36C(I)

4.0 (113)

15.1 (428) 5.0 (142) 6.4 (181) FRZR

3.8 (108) 4.0 (113) 4.6 (130) 5.2 (147) 3.0 (85) 6.6 (187) 3.4 (96)

4.9 (139) 2.0 (57) 2.5 (71)

3 5/8" (92)

*83 1/2" (2121) MIN TO 84 1/2" (2146) MAX

SHIPPING WEIGHT CO L U M N

WINE

18" Column 24" Column 30" Column 36" Column TA L L

L B (KG )

260 (118) 340 (154) 400 (181) 440 (200)

A 13/4" (45)

L B (KG )

30" Tall 36" Tall DRAWE R

24" Drawer 27" Drawer 30" Drawer 36" Drawer

400 (181) 460 (209)

B

L B (KG )

170 (77) 190 (86) 210 (95) 250 (113)

UNDERCOUNTER

COLUMN

IMPORTANT NOTE: Overall dimensions do not include panels

or handles. Dimensions will vary with panel thickness.

W

A

B

18" Column

18" (457)

2 1/2" (64)

16 1/2" (419)

24" Column

24" (610)

4" (102)

22 1/2" (572)

30" Column

30" (762)

5 5/8" (143)

28 1/2" (724)

36" (914)

7 1/4"

34 1/2" (876)

36" Column

48

|

Sub-Zero Customer Care 800.222.7820

(184)

I N T EG R AT ED R E FRIGE RATION

B U I L T- I N

Overall Dimensions TALL

D R AW ER W

W

24" (610)

24" (610) 1/4" (6)

4 1/2" (114)

13 5/16" (338)

(876)

3/8" (10)

10 9/16" (268)

44 7/8"

84"*

(2134)

PRO 48

34 1/2"* (1140)

3 5/8" (92) *34" (864) MIN TO 35" (889) MAX 3/8" (10)

13 5/16" (338)

I N T E G R AT E D

3/8" (10)

10 9/16" (268)

18 3/8" (467)

3 5/8" (92)

*83 1/2" (2121) MIN TO 84 1/2" (2146) MAX

DRAWER

A 13/4" (45)

(467)

TA LL

24" Drawer

24" (610)

27" Drawer

27" (686)

30" Drawer

30" (762)

36" Drawer

36" (914)

B

A

B

30" (762)

5 5/8" (143)

28 1/2" (724)

36" Tall

36" (914)

7 1/4" (184)

34 1/2" (876)

subzero.com/specs

|

49

UNDERCOUNTER

W

30" Tall

WINE

18 3/8"

W

B U I L T- I N

I N T EG R AT ED R E FRIGE RATION

Opening Dimensions I N T EG R AT ED OPENING DIMENSIONS

PRO 48

25" (635) OPENING DEPTH 25 3/4" (654) FOR OUTDOOR MODEL

C OL U MN | TA L L

W*

H

18" Column 24" Column 30" Column | Tall 36" Column | Tall

18" (457) 24" (610) 30" (762) 36" (914)

84" (2134) 84" (2134) 84" (2134) 84" (2134)

D RAWER TOP VIEW

24" Drawer 27" Drawer 30" Drawer 36" Drawer

W*

H

24" (610) 27" (686) 30" (762) 36" (914)

34 1/2" (876) 34 1/2" (876) 34 1/2" (876) 34 1/2" (876)

I N T E G R AT E D

*For stainless steel side panel accessory, add 1" (25) per panel to opening width.

H

W

OPENING HEIGHT

OPENING WIDTH

D U A L I N S TA LLATI O N

When installing two units side by side in a dual installation, the opening width is the width of the two units added together. A dual installation kit will be required for this installation. If a dual installation kit is not specified, a minimum 2" (51) filler strip is required between units.

WINE

SIDE VIEW

FRONT VIEW

NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry— 4 1/2" (114) for outdoor model.

3/4" (19)

3/4" (19)

TYPICAL

3 1/2" (89)

FINISHED RETURN

FINISHED RETURN

W FRAMELESS CABINETRY

50

|

TYPICAL

3 1/2" (89)

W

UNDERCOUNTER

The depth of each integrated model is 24" (610). Allow for panel thickness when planning the finished opening depth. A minimum 3 1/2" (89) finished return is required on all sides of the opening—41/2" (114) for outdoor model. Framed cabinets will require additional finished filler material behind the face frame for a proper installation. Refer to the illustration.

FRAMED CABINETRY

Sub-Zero Customer Care 800.222.7820

FILLER

Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero customer care at 800-222-7820.

I N T EG R AT ED R E FRIGE RATION

B U I L T- I N

Electrical

Plumbing

The electrical supply must be located within the shaded area shown in the illustration and chart below. A separate circuit servicing only this appliance is required.

The water supply line should be located within the shaded area shown in the illustration below. The water supply line should be connected to the house supply with an easily accessible shut-off valve. Do not use self‑piercing valves. The water supply line must not interfere with installation of the anti-tip bracket.

IMPORTANT NOTE: For outdoor model ID-24RO, a ground

The electrical outlet must be positioned with the grounding prong to the right of the thinner blades. Installation must comply with all applicable electrical codes.

A reverse osmosis system can be used provided there is constant water pressure of 35–120 psi (2.4–8.3 bar) supplied to the unit at all times. A copper line is not recommended for this application.

PRO 48

fault circuit interrupter (GFCI) is required to reduce the risk of electrical shock. A GFCI is not recommended for use with indoor models and may cause interruption of operation.

Installation must comply with all applicable plumbing codes.

ELECTRICAL REQUIREMENTS

Electrical Supply

115 VAC, 60 Hz

Service

15 amp dedicated circuit

Receptacle

3-prong grounding-type

PLUMBING REQUIREMENTS 1/4"

Water Supply Pressure

35–120 psi (2.4–8.3 bar)

Excess Line for Connection 18" Model

6" (152)

24" Model

9 1/2" (241)

27" Model

11" (279)

30" Model

12 1/2" (318)

36" Model

15 1/2" (394)

WATER SUPPLY LOCATION

3" (76)

24" Model

5 1/2" (140)

30" Model

6" (152)

36" Model

9" (229)

RIGHT SIDE OF OPENING

A A

4 1/4" (108)

1/4" (6)

WINE

(114)

A

18" Model

LEFT SIDE OF OPENING

41/2"

36" (914)

A

I N T E G R AT E D

ELECTRICAL SUPPLY LOCATION

OD copper, braided stainless steel or PEX tubing

FLOOR

Electrical supply location.

6" (152)

3" (76) AREA EXTENDS 1/2" (13) FORWARD ON FLOOR

Water supply location.

|

51

UNDERCOUNTER

subzero.com/specs

PRO 48

B U I L T- I N

I N T EG R AT ED R E FRIGE RATION

Stainless Steel Panels

Custom Panels

The outdoor model requires the use of Sub-Zero stainless steel outdoor accessory panels. Stainless steel panels are available through an authorized Sub‑Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com.

For integrated models, custom door panels and handle hardware must be provided. Refer to the panel requirements chart and typical panel dimensions.

The thickness of indoor stainless steel panels is 3/4" (19) and outdoor stainless steel panels are 11/2" (38). The depth of each integrated model is 24" (610). Allow for panel thickness when planning the finished opening depth. Reveals of 1/8" (3) are typical, however, the reveal between the upper and lower outdoor stainless steel panels is 1/4" (6) to accommodate the lock.

The thickness of the custom panel can vary. A minimum 5/8" (16) thick panel is required, but the thickness can be increased provided it does not exceed the weight limit. The depth of each integrated model is 24" (610). Allow for panel thickness when planning the finished opening depth. Refer to the full-scale template on page 55. CAUTION As reveals between cabinetry and the unit decrease, severe finger pinching can occur while door is closing.

Finish all sides of custom panels. They will be visible when the door/drawer is open. I N T E G R AT E D

D-style handles are recommended. Door handles must be located near the edge of the panel opposite the hinge and should be centered top to bottom. Drawer handles must be located near the top edge of each panel. Stainless steel tubular and pro handles are avail­able through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. PANEL REQUIREMENTS WEIGH T PER PAN EL

18" Column 24" Column 30" Column 36" Column WINE

WEIGH T PER PA N EL

30" Tall (door) 36" Tall (door) Drawer PAN EL TH IC KN ESS

UNDERCOUNTER

All Panels

52

|

Sub-Zero Customer Care 800.222.7820

MAX

45 lb (20 kg) 60 lb (27 kg) 75 lb (34 kg) 75 lb (34 kg) MAX

50 lb (22 kg) 60 lb (27 kg) 15 lb (7 kg) M IN 5/8"

(16)

I N T EG R AT ED R E FRIGE RATION

B U I L T- I N

Custom Panels D O O R PA N EL H EI GH T

T Y PICAL PANEL DIME NSIONS

The height of the custom door panel can extend beyond the typical panel height, provided it does not exceed the weight limit. Refer to the illustration below. 79 7/8"

49 3/8" (1254)

PRO 48

(2029)

1 3/4" (45)

13 9/16" (345)

A DECORATIVE VALANCE CANNOT EXTEND BEYOND THIS PLANE

1/8" (3)

16 11/16" (424)

W

Column

W

Tall

DOOR PANEL

W

Drawer

84"

24" (610) TO BACK OF UNIT

(2134)

PANEL WIDTH

HINGE

I N T E G R AT E D

Typical panel dimensions are based on an 84" (2134) finished height for column and tall models and 34 1/2" (876) for drawer models, with a 4" (102) toe kick and 1/8" (3) reveals. Panel dimensions must be adjusted accordingly for all other installations. Refer to the illustration for panel heights and the chart below for panel widths. W

18" Model

17 3/4"

24" Model

23 3/4" (603)

27" Model

26 3/4" (679)

30" Model

29 3/4" (756)

36" Model

35 3/4" (908)

(451)

Upper valance—column and tall (side view).

WINE

D UAL INS TALLATION

For dual installations, refer to the illustration for panel heights and the chart below for panel widths. PANEL WIDTH

W

18" Model

17 13/16"

24" Model

23 13/16" (605)

27" Model

26 13/16" (681)

30" Model

29 13/16" (757)

36" Model

35 13/16" (910)

(452)

|

53

UNDERCOUNTER

subzero.com/specs

PRO 48

B U I L T- I N

I N T EG R AT ED R E FRIGE RATION

Custom Panels

Standard Handles

TOE KICK CLEARANCE (EXCLUDES OUTDOOR MODEL)

Optional stainless steel tubular and pro handles are avail­ able through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com.

The height of the toe kick area can extend beyond the typical toe kick height, provided it does not exceed the dimensions in the illustration below. Toe kick heights from 2" (51) to 3 7/8" (98) require a reduced toe kick accessory available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero customer care at 800-222-7820.

HINGE**

VENTED LOUVERS

I N T E G R AT E D

24" (610) TO BACK OF UNIT DOOR PANEL

1 1/8" (29) MAX TOE KICK ADJUSTMENT

2" (51)* TO

6" (152) FROM FLOOR

A DECORATIVE TOE KICK CANNOT EXTEND BEYOND THIS PLANE

UNDERCOUNTER

WINE

*2" (51) to 3 7/8" (98) requires sales accessory. **Column models only.

Toe kick (side view).

54

|

Sub-Zero Customer Care 800.222.7820

Refer to the chart below for standard handle lengths for integrated models. HANDLE LENGTH

Column Door

TU BU L A R

50 1/8"

(1273)

PRO

48 3/8"

(1229)

Tall Door

33 1/4"

24" Drawer

21 1/4" (540)

19 1/2" (495)

27" Drawer

24 1/4" (616)

22 1/2" (572)

30" Drawer

27 1/4" (692)

25 1/2" (648)

36" Drawer

33 1/4"

31 1/2" (800)

(845)

(845)

31 1/2"

(800)

I N T EG R AT ED R E FRIGE RATION

B U I L T- I N

Maximum Door Opening F ULL-S CALE T E MPL ATE

As the panel width and/or depth increases, so does the potential for panel interference. Interference may be minimized by utilizing the 90° door stop.

PRO 48

3/4" (19) PANEL

DOOR OPEN MAXIMUM 105°

POTENTIAL INTERFERENCE

I N T E G R AT E D

1/8" (3) REVEAL

DOOR CLOSED 3/4" (19) PANEL

ADJACENT CABINETRY

WINE

POTENTIAL INTERFERENCE

1" (25) SCALE

Maximum door opening (top view).

subzero.com/specs

|

55

UNDERCOUNTER

0"

W INE S T O R AG E

B U I L T- I N

Wine Storage Wine finds a well-deserved place of honor in a Sub-Zero wine storage unit. Every detail is designed to ensure better wine preservation. Cherrywood-faced racks, soft lighting, custom cabinetry if desired—Sub-Zero helps make a wine collection an element of beauty in the home. PRO 48

W INE S T O R AG E MODE L S

424G

424FSG

UW-24FS

IW-24

IW-30

IW-30R

I N T E G R AT E D

UW-24

IW-18

WS-30

BW-30

WINE

|

57

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

W INE S T O R AG E

Overall Dimensions M ODEL 424G | UW-24 23 7/8" (606)

MO D EL 4 2 4 FS G | U W-2 4 FS 24 1/4" (616)

24" (610)

34 3/16"

PRO 48

34"

(864)

(868)

I N T E G R AT E D

4" (102)

4" (102)

25 3/8"

25 3/8"

(645)

(645)

1 3/4" (44)

1 3/4" (44)

SPECIFICATIONS ST O R A G E C A PA C I TY

WINE

424G, UW-24 424FSG, UW-24FS

UNDERCOUNTER

BOTTL ES*

46 46

SH I P P I N G W E I G H T

L B (KG )

424G, UW-24 424FSG, UW-24FS

195 (88) 220 (100)

*750 ml bottles.

58

|

Sub-Zero Customer Care 800.222.7820

24 5/8" (625)

Overall dimensions for models 424G and UW-24 are based on the stainless steel models. Refer to page 81 for door clearance information. Freestanding models 424FSG and UW-24FS have a finished stainless steel exterior and handle.

W INE S T O R AG E

B U I L T- I N

Opening Dimensions M ODEL 424G | UW-24

24" (610) OPENING DEPTH

PRO 48

TOP VIEW

34 1/2"

W

(876) OPENING HEIGHT

OPENING WIDTH

I N T E G R AT E D

SIDE VIEW

FRONT VIEW

NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry.

3/4" (19)

3/4" (19) TYPICAL

TYPICAL

3 1/2" (89)

3 1/2" (89)

FINISHED RETURN

FINISHED RETURN

W

FILLER

W FRAMELESS CABINETRY

FRAMED CABINETRY

WINE

OPENING WIDTH

424G, UW-24

DUAL OPENING WIDTH

Two 24" Models

W

24" (610)

W

48 1/8" (1222)

Dual installation kit required.

|

59

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

W INE S T O R AG E

Overall Dimensions C OLUMN

TALL W

W

24" (610)

PRO 48

4 1/2" (114)

4 1/2" (114)

69 1/2"

84"*

(2134)

24" (610)

44 7/8"

84"*

(1765)

(2134)

(1140)

3/8" (10)

13 5/16" (338)

I N T E G R AT E D

3/8" (10)

10 9/16" (268)

3 5/8" (92)

*83 1/2" (2121) MIN TO 84 1/2" (2146) MAX

A

A

WINE

13/4" (45)

UNDERCOUNTER

13/4" (45)

17 3/4"

B

COLUMN

3 5/8" (92)

*83 1/2" (2121) MIN TO 84 1/2" (2146) MAX

(451)

W

A

B

IW-18

18" (457)

2 1/2" (64)

16 1/2" (419)

IW-24

24" (610)

4" (102)

22 1/2" (572)

IW-30

30" (762)

5 5/8" (143)

28 1/2" (724)

TALL

IW-30R

B

W

A

B

30" (762)

5 5/8" (143)

28 1/2" (724)

IMPORTANT NOTE: Overall dimensions do not include panels

or handles. Dimensions will vary with panel thickness.

60

|

Sub-Zero Customer Care 800.222.7820

W INE S T O R AG E

B U I L T- I N

Specifications STORAGE CAPACITY CO L U M N

BOTTL ES*

IW-18 IW-24 IW-30 TA L L

RE FR

BOTTL ES*

4.0 cu ft (113 L)

86

PRO 48

IW-30R

59 102 146

*750 ml bottles.

SHIPPING WEIGHT CO L U M N

IW-18 IW-24 IW-30 TA L L

IW-30R

L B (KG )

350 (159) 410 (186) 460 (209) L B (KG )

490 (222)

I N T E G R AT E D WINE

|

61

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

W INE S T O R AG E

Opening Dimensions I N T EG R AT ED WINE STORAGE OPENING DIMENSIONS

25" (635) OPENING DEPTH

W*

18" Column

18" (457)

24" Column

24" (610)

30" Column | Tall

30" (762)

PRO 48

*For stainless steel side panel accessory, add 1" (25) per panel to opening width.

TOP VIEW

The depth of each integrated (IW) model is 24" (610). Allow for panel thickness when planning the finished opening depth. A minimum 3 1/2" (89) finished return is required on all sides of the opening. Framed cabinets will require additional finished filler material behind the face frame for a proper installation. Refer to the illustration.

I N T E G R AT E D

D U AL I N S TALLATI O N

84"

W

(2134) OPENING HEIGHT

OPENING WIDTH

The unit can be installed next to an integrated refrigeration model or another integrated wine storage model in a dual installation. When installing two units side by side, the opening width is the width of the two units added together. A dual installation kit will be required for this installation. If a dual installation kit is not specified, a minimum 2" (51) filler strip is required between units. Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero customer care at 800-222-7820.

WINE

SIDE VIEW

FRONT VIEW

NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry.

3/4" (19)

3/4" (19)

TYPICAL

3 1/2" (89)

FINISHED RETURN

FINISHED RETURN

UNDERCOUNTER

W

W FRAMELESS CABINETRY

62

|

TYPICAL

3 1/2" (89)

FRAMED CABINETRY

Sub-Zero Customer Care 800.222.7820

FILLER

W INE S T O R AG E

B U I L T- I N

Overall Dimensions M ODEL WS -30 | BW-30

SPECIFICATIONS 26 3/16" (665)

30" (762)

STORAGE C A PAC ITY

B OT T LE S *

WS-30 BW-30 SH IPP IN G WEIGH T

LB ( K G )

445 (202) 445 (202)

*750 ml bottles.

84"

(2134)

PRO 48

WS-30 BW-30

147 146

73 3/4" (1873)

4" (102)

I N T E G R AT E D

HEIGHT DIMENSIONS ± 1/2" (13)

23 7/8" (606)

23 7/8" (606)

17"

(432)

311/4" (796)

WINE

2 3/8" (60)

Overall dimensions are based on the stainless steel model. For flush inset applications, add 1/2" (13) to door clearance dimensions.

|

63

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

W INE S T O R AG E

Opening Dimensions M ODEL WS -30 | BW-30 STANDARD INSTAL LATI O N

24" (610) OPENING DEPTH

3/4" (19) TYPICAL

3 1/2" (89)

PRO 48

FINISHED RETURN

TOP VIEW

W FRAMELESS CABINETRY

3/4" (19) TYPICAL

3 1/2" (89)

I N T E G R AT E D

FINISHED RETURN

83 3/4"

W

(2127) OPENING HEIGHT

OPENING WIDTH

WINE

SIDE VIEW

FILLER

W FRAMED CABINETRY

FRONT VIEW

NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry. Shaded line represents profile of unit.

OPENING WIDTH

W

WS-30

29 1/2" (749)

BW-30

29 1/2" (749)

If an 83" (2108) grille height is specified, the opening height must be decreased by 7/8" (22). If an 88" (2235) grille height is specified, the opening height must be increased by 4" (102).

UNDERCOUNTER

If two units are installed side by side, refer to page 66 for dual standard installations.

64

|

Sub-Zero Customer Care 800.222.7820

W INE S T O R AG E

B U I L T- I N

Opening Dimensions M ODEL WS -30 | BW-30 FL USH INSE T INSTA LLATI O N

26 3/16" (665) FLUSH INSET DEPTH

5 11/16" 3 1/2"

2 3/16" (56)

FINISHED CLEATS

TOP VIEW

CLEAT 3/4" (19) TYPICAL

PRO 48

(89) (145) FINISHED RETURN

W FRAMELESS CABINETRY

11/4"

1/4" (6)

(32)

5 11/16" 3 1/2"

(89) (145) FINISHED RETURN

W FLUSH INSET WIDTH

3/4" (19) TYPICAL

I N T E G R AT E D

SIDE VIEW

84" (2134) FLUSH INSET HEIGHT

CLEAT FILLER

W FRAMED CABINETRY

FRONT VIEW

WINE

NOTE: 3 1/2" (89) finished returns and shaded areas will be visible and should be finished to match cabinetry. Shaded line represents profile of unit with 3/4" (19) panel.

FLUSH INSET WIDTH

W

WS-30

32" (813)

BW-30

32" (813)

Dimensions assume a 3/4" (19) panel thickness. If an 83" (2108) grille height is specified, the flush inset height must be decreased by 7/8" (22). If an 88" (2235) grille height is specified, the flush inset height must be increased by 4" (102).

subzero.com/specs

|

65

UNDERCOUNTER

If two units are installed side by side, refer to page 67 for dual flush inset installations.

B U I L T- I N

W INE S T O R AG E

Opening Dimensions M ODEL WS -30 | BW-30 DUAL STANDARD IN S TALLATI O N

24" (610) OPENING DEPTH

3/4" (19) TYPICAL

3 1/2" (89)

PRO 48

FINISHED RETURN

TOP VIEW

W FRAMELESS CABINETRY

3/4" (19) TYPICAL

3 1/2" (89)

I N T E G R AT E D

FINISHED RETURN

83 3/4"

W

(2127) OPENING HEIGHT

OPENING WIDTH

WINE

SIDE VIEW

W FRAMED CABINETRY

FRONT VIEW

NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry. Shaded line represents profile of unit.

DUAL OPENING WIDTH

UNDERCOUNTER

FILLER

W

WS-30 and 30" Built-In Model

59 3/4" (1518)

BW-30 and 30" Built-In Model

59 3/4" (1518)

WS-30 and 36" Built-In Model

65 3/4" (1670)

BW-30 and 36" Built-In Model

65 3/4" (1670)

66

|

Sub-Zero Customer Care 800.222.7820

A dual installation kit will be required for this installation.

W INE S T O R AG E

B U I L T- I N

Opening Dimensions M ODEL WS -30 | BW-30 DUAL FL USH INSE T I N S TA LLATI O N

26 3/16" (665) FLUSH INSET DEPTH

5 11/16" 3 1/2"

2 3/16" (56)

FINISHED CLEATS

TOP VIEW

CLEAT 3/4" (19) TYPICAL

PRO 48

(89) (145) FINISHED RETURN

W FRAMELESS CABINETRY

11/4"

1/4" (6)

(32)

5 11/16" 3 1/2"

(89) (145) FINISHED RETURN

W FLUSH INSET WIDTH

SIDE VIEW

3/4" (19) TYPICAL

I N T E G R AT E D

84" (2134) FLUSH INSET HEIGHT

CLEAT FILLER

W FRAMED CABINETRY

FRONT VIEW

WINE

NOTE: 3 1/2" (89) finished returns and shaded areas will be visible and should be finished to match cabinetry. Shaded line represents profile of unit with 3/4" (19) panel.

DUAL FLUSH INSET WIDTH

W

WS-30 and 30" Built-In Model

62 1/4" (1581)

BW-30 and 30" Built-In Model

62 1/4" (1581)

WS-30 and 36" Built-In Model

68 1/4" (1734)

BW-30 and 36" Built-In Model

68 1/4" (1734)

Dimensions assume a 3/4" (19) panel thickness. A dual installation kit will be required for this installation.

|

67

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

W INE S T O R AG E

Electrical

PRO 48

The electrical supply must be located within the shaded area shown in the illustration for your specific model. For integrated (IW) models, also refer to the chart. A separate circuit servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

ELECTRICAL LOCATION—INTEGRATED

18" Model

6" (152)

24" Model

9 1/2" (241)

30" Model

12 1/2" (318)

If the unit will be connected to a home security system, allow 36" (914) of excess wiring for proper connection. IMPORTANT NOTE: For integrated and undercounter

models, the electrical outlet must be positioned with the grounding prong to the right of the thinner blades. Installation must comply with all applicable electrical codes.

LEFT SIDE OF OPENING

41/2" (114)

A 4 1/4"

ELECTRICAL REQUIREMENTS

(108)

Electrical Supply

115 VAC, 60 Hz

I N T E G R AT E D

Service

15 amp dedicated circuit

Receptacle

Integrated models.

7"

E

(178)

6"

(152)

2"

(51)

15 1/2" (394)

3" (76)

75 1/2" (1918) FROM FLOOR

WINE

FLOOR

UNDERCOUNTER

1/4" (6)

FLOOR

3-prong grounding-type

LEFT SIDE OF OPENING

Model 424G, UW-24.

68

|

RIGHT SIDE OF OPENING

Model WS-30, BW-30.

Sub-Zero Customer Care 800.222.7820

A

W INE S T O R AG E

B U I L T- I N

Custom Panels

Custom Panel—424G | UW-24

For framed, overlay, integrated and flush inset applications, a custom door panel must be provided. Handle hardware must also be provided for overlay, integrated and flush inset applications. Refer to panel requirements and custom panel dimensions charts for your specific model and design application.

For models 424G and UW-24, the custom door panel will attach directly to the door frame with screws through a series of pre-drilled holes.

Do not install a solid panel on a glass door unit. A solid door is available as a sales accessory (except models WS-30 and BW-30) and must be installed if a solid panel is being specified. Service may be required to install the door. Contact an authorized Sub-Zero dealer for more information. Overall dimensions are the same for glass and solid door panels.

WEIGH T PER PAN EL

MAX

424G, UW-24

10 lb (5 kg)

PAN EL TH IC KN ESS

M IN 5/8"

424G, UW-24

(16)

O V ER LAY PAN EL D I M EN S I O N S A

A

A

H

I N T E G R AT E D

Models 424FSG and UW-24FS have a finished stainless steel exterior that is designed to be used in a freestanding application.

PANEL REQUIREMENTS

PRO 48

Finish all sides of the custom panels. They may be visible when the door is open or through the window of glass door models.

Refer to the charts for panel requirements and dimensions.

A W

424G, UW-24 PANEL DIMENSIONS PAN EL

424G, UW-24

W

H

23 3/4" (603)

30 1/16" (764)

STIL ES | RAIL S

Minimum

A

2 1/4" (57)

D O O R C LEAR A N C E

|

69

UNDERCOUNTER

subzero.com/specs

WINE

Models 424G and UW-24 can be installed flush with surrounding cabinetry. Depending on the thickness of the overlay door panel, it may be necessary to install the unit 1/4" (6) beyond the front surface of adjacent cabinetry to prevent interference when the door is opened to 145°. Refer to the full-scale template on page 81.

B U I L T- I N

W INE S T O R AG E

Custom Panel—Integrated For integrated (IW) models, a custom door panel and handle hardware must be provided. Refer to the panel requirements chart and typical panel dimensions.

PRO 48

Do not install a solid panel on the glass door unit. A solid door is available as a sales accessory through an authorized Sub-Zero dealer. The thickness of the custom panel can vary. A minimum 5/8" (16) thick panel is required, but the thickness can be increased provided it does not exceed the weight limit. The depth of each integrated model is 24" (610). Allow for panel thickness when planning the finished opening depth. Refer to the full-scale template on page 55. Finish all sides of custom panels. They will be visible when the door/drawer is open.

W E I G H T P E R PA N E L

Door Frame (column) Door Frame (tall) Drawer Panel (tall) PA N E L T H I C K N E S S

All Panels

UNDERCOUNTER

WINE

I N T E G R AT E D

PANEL REQUIREMENTS

70

|

Sub-Zero Customer Care 800.222.7820

MA X

35 lb (16 kg) 25 lb (11 kg) 15 lb (7 kg) MIN 5/8"

(16)

CAUTION As reveals between cabinetry and the unit decrease, severe finger pinching can occur while door is closing.

D-style handles are recommended. Door handles must be located near the edge of the panel opposite the hinge and should be centered top to bottom. Drawer handles must be located near the top edge of each panel. Stainless steel tubular and pro handles are avail­able through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com.

W INE S T O R AG E

B U I L T- I N

Custom Panel—Integrated D U AL I N S TALLATI O N

T Y PICAL PANEL DIME NSIONS

For dual installations, refer to the illustration for panel height and the chart below for panel width. PANEL WIDTH 79 7/8"

49 3/8"

MOD EL

(1254)

18" Model 24" Model 30" Model

W

17 13/16" (452) 23 13/16" (605) 29 13/16" (757)

13 9/16"

PRO 48

(2029)

(345)

16 11/16" (424)

W

Column

W

Tall

I N T E G R AT E D

Typical panel dimensions are based on an 84" (2134) finished height, 4" (102) toe kick and 1/8" (3) reveals. Panel dimensions must be adjusted accordingly for all other installations. Refer to the illustration for panel height and the chart below for panel width. PANEL WIDTH MODEL

18" Model 24" Model 30" Model ST I L E S | R A I L S

MIN

3 1/4" (83) 7 3/4" (197) 9 1/2" (241) 4 1/2" (114)

WINE

Stiles Top Rail Bottom Rail (column) Bottom Rail (tall)

W

17 3/4" (451) 23 3/4" (603) 29 3/4" (756)

|

71

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

W INE S T O R AG E

Custom Panel—Integrated TO E K I C K C LEAR A N C E

The height of the custom door panel can extend beyond the typical panel height, provided it does not exceed the weight limit. Refer to the illustration below.

The height of the toe kick area can extend beyond the typical toe kick height, provided it does not exceed the dimensions in the illustration below. Toe kick heights from 2" (51) to 3 7/8" (98) require a reduced toe kick accessory available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero customer care at 800-222-7820.

PRO 48

D OO R PANEL HEIGHT

1 3/4" (45) A DECORATIVE VALANCE CANNOT EXTEND BEYOND THIS PLANE

1/8" (3)

DOOR PANEL

84"

24" (610)

(2134)

TO BACK OF UNIT

HINGE**

24" (610) TO BACK OF UNIT

I N T E G R AT E D

HINGE DOOR PANEL

1 1/8" (29) MAX TOE KICK ADJUSTMENT

2" (51)* TO

6" (152) FROM FLOOR

Upper valance (side view).

*2" (51) to 3 7/8" (98) requires sales accessory. **Column models only.

Toe kick (side view).

WINE UNDERCOUNTER

VENTED LOUVERS

72

|

Sub-Zero Customer Care 800.222.7820

A DECORATIVE TOE KICK CANNOT EXTEND BEYOND THIS PLANE

W INE S T O R AG E

B U I L T- I N

Custom Panel—WS-30 | BW-30 F R AMED

FR AM ED PAN EL D I M EN S I O N S

The framed application is an overlay model with framed design features. It is not a separate model.

H A

1/4"

Routing, recessing and optional extended handles may be required for finger clearance. Refer to the full-scale template on page 82.

A

A

H

PRO 48

(6), a filler material If the custom panel is thinner than must be added to achieve a proper fit. If the panel is thicker than 1/4" (6), rout an edge around the panel or mount the custom panel on a sheet of 1/4" (6) thick material and insert into the channel.

A W

PANEL REQUIREMENTS W E I G H T P E R PA N E L

Door Grille (optional) Framed

75 lb (34 kg) 13 lb (6 kg) MIN 1/4"

(6)

WS-30, BW-30 PANEL DIMENSIONS FRAMED PAN EL

Door Grille (optional)

W

H

29 3/4" (756) 29 3/4" (756)

69 9/16" (1767) 8 15/16" (227)

STIL ES | RAIL S

Minimum

A

3 3/16" (81)

I N T E G R AT E D

PA N E L T H I C K N E S S

MA X

WINE

|

73

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

W INE S T O R AG E

Custom Panel—WS-30 | BW-30 O VER LAY

O VER LAY PA N EL D I MEN S I O N S

Overlay panels are typically created by combining a 3/4" (19) custom panel, a .10" (3) spacer panel and a 1/4" (6) backer panel. Refer to the illustrations below.

PRO 48

PANEL REQUIREMENTS W E I G H T P E R PA N E L

MA X

Door Grille

H A

A

A

H

75 lb (34 kg) 13 lb (6 kg)

PA N E L T H I C K N E S S

MIN 5/8"

Overlay

(16) A W

CUSTOM PANEL

SPACER PANEL

SPACER PANEL

WS-30, BW-30 OVERLAY PANELS

CUSTOM PANEL

I N T E G R AT E D

D OOR BACKER PANEL

BACKER PANEL

TRIM DOOR FRAME

GLASS

Overlay Panel Spacer Panel Backer Panel GRIL L E

5/16" (8) min 1/8" (3)

3/4" (19) typical

.10" (3) 1/4" (6)

Panel assembly (cross section). Panel assembly (rear view).

Overlay Panel Spacer Panel Backer Panel

W

H

30" (762) 29 1/8" (740) 29 3/4" (756)

69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767)

W

H

30" (762) 29 1/8" (740) 29 3/4" (756)

9 1/4" (235)* 8 5/16" (211) 8 15/16" (227)

STIL ES | RAIL S

Minimum

A

3 1/4" (83)

*Panel height may be increased by 7/16" (11) to hide upper main frame. Also refer to built-in panel configurator at subzero.com/trade/panels.

UNDERCOUNTER

WINE

Grille panel dimensions are for standard 84" (2134) overall unit height. For 83" (2108) height, subtract 1" (25) from grille panel height dimensions and for 88" (2235) height, add 4" (102). A specific panel grille must be ordered for an 83" or 88" overall unit height.

74

|

Sub-Zero Customer Care 800.222.7820

W INE S T O R AG E

B U I L T- I N

Custom Panel—WS-30 | BW-30 F LUS H INS ET

FLU S H I N S ET PA N EL D I MEN S I O N S

The flush inset application is an overlay model with flush inset panels. It is not a separate model.

H A

A

For flush inset panels thicker than 3/4" (19), a 90° door stop may be required to prevent interference with adjacent cabinets. Refer to the full-scale template on page 85. PANEL REQUIREMENTS W E I G H T P E R PA N E L

Door Grille Flush Inset

H

A W

WS-30, BW-30 MA X

75 lb (34 kg) 13 lb (6 kg) MIN 5/8"

(16)

FLUSH INSET PANELS D OOR

Flush Inset Panel Spacer Panel Backer Panel GRIL L E

Flush Inset Panel Spacer Panel Backer Panel

W

H

31" (787) 29 1/8" (740) 29 3/4" (756)

69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767)

W

H

31" (787) 29 1/8" (740) 29 3/4" (756)

9 1/4" (235) 8 5/16" (211) 8 15/16" (227)

STIL ES | RAIL S

Minimum

I N T E G R AT E D

PA N E L T H I C K N E S S

A

PRO 48

The flush inset design allows custom panels to be installed flush with adjacent cabinets. Similar to overlay, flush inset panels are typically created by combining a 3/4" (19) custom panel, a .10" (3) spacer panel and a 1/4" (6) backer panel. Refer to the illustrations for overlay panels on the previous page.

A

3 3/4" (95)

Grille panel dimensions are for standard 84" (2134) overall unit height. For 83" (2108) height, subtract 1" (25) from grille panel height dimensions and for 88" (2235) height, add 4" (102). A specific panel grille must be ordered for an 83" or 88" overall unit height.

WINE

|

75

UNDERCOUNTER

subzero.com/specs

5/16" (8)

B U I L T- I N

W INE S T O R AG E

5/8" (16)

TOP VIEW

TOP VIEW

CABINETRY

DOOR / DRAWER / GRILLE

1/2" (13)

BACKER

1/8" 5/16" (3) (8)

CABINETRY GRILLE

The illustrations provide offsets and reveals for model FLUSHpanel INSET PANEL WS-30 or BW-30 in a flush inset application. Refer to the 5/16" (8) 1/2" chart below for reference to the illustrations. (13) 5/8" (16)

PRO 48

PANEL OFFSET

DOOR

DOOR

DOOR

1/8" (3) BACKER

Grille Top

B

Grille Bottom | Door Top

C

Door Bottom

D

REVEAL

DOOR

GRILLE

5/16" (8) 5/8" (16)

5/16" (8)

1/2" (13)

1/8" (3) 1/4" (6)

SIDE VIEW

REVEAL

Illus. B

DOOR / DRAWER

5/16" (8) 3/32" GRILLE (2)

1/2" (13)

5/16" (8) 5/32" (4)

DOOR

I N T E G R AT E D

DOOR

1 /16" (3) (8)

/8" SIDE 5 VIEW

FLUSH INSET PANEL

CABINETRY

1/8" 5/16" (3) (8)

5/8" (16)

SIDE VIEW

1/2" (13) 3/32" 5/16" (2) (8) 1/8" 5SIDE /16" (3) VIEW (8)

5/32" DOOR 5/16" (4) (8) SIDE VIEWGRILLE

5/16" (8)

1/2" (13)

CABINETRY DRAWER

Illus. C

5/16" (8) 5/32" (4)

5/16" GRILLE (8) 3/32 " (2) DOOR SIDE VIEW

Illus. D DRAWER

SIDE VIEW

WINE

3/32" 1/2" (13) 5/16" (2) (8)

CABINETRY

1/4" (6)

Illus. A

GRILLE

TOP VIEW

CABINETRY

5/16" (8)

IL L U S

A

1/2" (13)

TOP VIEW

DOOR / DRAWER / GRILLE

SIDE SPACER VIEW

Door | Grille Sides

5/16" (8) 5/32" (4)

GRILLE

Custom Panel—WS-30 | BW-30 F LUS H INS ET PA SPACER NE L OFFSE T

1/2" (13)

5/32" (4) 5/8" (16)

1/2

DOOR

3/32" 5/16" (2) (8)

5/32" 5/16" (4) (8)

SIDE VIEW

SIDE VIEW

DOOR / DRAWER

5/16" (8) 3/32" (2) DOOR

5/8" (16)

DRAWER

5/32" 5/16" (4) (8)

5/16" (8) 5/16" (8) 3/32" (2) DOOR

SIDE VIEW

UNDERCOUNTER

DOOR / DRAWER

SIDE VIEW

DRAWER

5/32" 5/8"(4) (16)

5/16" (8)

5/32" 5/16" (4) (8)

5 SIDE VIEW

76

|

Sub-Zero Customer Care 800.222.7820

SIDE VIEW

W INE S T O R AG E

B U I L T- I N

Custom Panel—WS-30 | BW-30 D U AL FLU S H I N S ET PA N EL D I MEN S I O N S

D U AL INS TALLATIONS

Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero customer care at 800-222-7820.

A

A

A

H

A W

WS-30, BW-30 DUAL FLUSH INSET PANELS D OOR

Flush Inset Panel Spacer Panel Backer Panel GRIL L E

Flush Inset Panel Spacer Panel Backer Panel

W

H

30 1/2" (775) 29 1/8" (740) 29 3/4" (756)

69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767)

W

H

30 1/2" (775) 29 1/8" (740) 29 3/4" (756)

9 1/4" (235) 8 5/16" (211) 8 15/16" (227)

STIL ES | RAIL S

Minimum

I N T E G R AT E D

For dual standard installations, panel dimensions are the same as for single installations. Refer to the chart on page 74. Panel dimensions and offsets for dual flush inset installations are listed on the following pages.

H

PRO 48

A dual installation kit may be required if two models WS-30 or a model WS-30 and built-in unit are installed side by side, or two models BW-30 or a model BW-30 and built-in unit. Installations without a custom filler strip require a dual installation kit. If a dual installation kit is not specified, a 2" (51) filler strip is recommended between units. Dual installations without a filler strip can only be accomplished using two units with opposite hinges. Refer to the illustrations below.

A

3 3/4" (95)

Grille panel dimensions are for standard 84" (2134) overall unit height. For 83" (2108) height, subtract 1" (25) from grille panel height dimensions and for 88" (2235) height, add 4" (102). A specific panel grille must be ordered for an 83" or 88" overall unit height. WITHOUT FILLER STRIP

WINE

Opposite hinges.

FILLER STRIP

Same side hinges.

|

77

UNDERCOUNTER

subzero.com/specs

W INE S T O R AG E

TOP VIEW

TOP VIEW

B U I L T- I N

DOOR / DRAWER / GRILLE

BACKER SPACER

DOOR

CABINETRY TOP VIEW

5/16" (8) Custom Panel—WS-30 | BW-30 1/2" 5/8"

(13)

D U AL F LUS H IN SE T PANE L OFFSE T (16)

1/8" (3)

BACKER SPACER

BACKER CABINETRY SPACER

IL L U S

Door (hinge) | Grille Sides

A

Door (handle) Sides

B

Grille Top

CABINETRY

CABINETRY

TOP VIEWREVEAL

BACKER

GRILLE

1/8" 5/16" (3) (8)

E

5/8" (16)

5/16" (8) 5/8" (16) GRILLE

Illus. A

CABINETRY

I N T E G R AT E D

GRILLE

TOP VIEW

5/16" (8)

5/16" (8)

DOOR 1/8" (3)

DOOR DOOR 1 /8" (3)

DOOR

1/4" (6)

1/4" (6)

REVEAL

REVEAL

FLUSH INSET PANEL

1/8" 5/16" (3)GRILLE (8)

CABINETRY

1/2" (13)

5/16" (8)

5/16" (8)

1/8" (3)

1/8" (3)

1/4" (6)

1/4" (6)

REVEAL

REVEAL

5/16" (8) 5/32" (4)

Illus. B

1/2" (13)

CABINETRY

1/2" (13) DOOR

SIDE VIEW

1/2" (13)

CABINETRY

5/8" SPACER (16)

DOOR

DUAL TRIM

5/16" (8)

1/2" (13)

DOOR DOOR TOP VIEW

DOOR / DRAWER / GRILLE FLUSH INSET PANEL

D 1/2" (13)

Door Bottom

DOOR

1/4" (6)

C

Grille Bottom | Door Top

TOP VIEW

DOOR / DRAWER / GRILLE

5/16" (8)

The illustrations provide panel offsets and reveals for model FLUSH INSET PANEL WS-30 or BW-30 in a dual flush inset application. Refer to 5/16" (8) the chart below for reference to the illustrations. PANEL OFFSET

TOP VIEW

TOP VIEW

DOOR / DRAWER / GRILLE

FLUSH INSET PANEL

PRO 48

DOOR

1 3/32" /2" (13) 5/16" (2) (8) 1/8" 5/16VIEW SIDE " (3) (8) 1/2" (13)

GRILLE SIDE VIEW

5/16" (8) 5/32" (4)

1/2" (13) DOOR

1/2 5/16" 32"" (8) 53//32 5/16" (4) (2) (8)

DOOR

3/32 GRILLE " 5/16" (2) (8)

1/8" 5/16 " (3) SIDE VIEW (8)

Illus. C

DOOR / DRAWER

5/16" (8) 5/32GRILLE " (4)

GRILLE

SIDE VIEW

SIDE VIEW

1/2

DOOR

Illus. D

3/32" 5/16" (2) (8)

SIDE VIEW

SIDE VIEW

5/16" (8) 3/32" (2) DOOR

WINE

5/8" (16)

DRAWER

5/32" 5/16" (4) (8)

5/16" (8) 5/16" (8) 3/32" (2) DOOR

DRAWER

5/DRAWER Illus. 32E " 5/16" (4) (8) DOOR SIDE VIEW

UNDERCOUNTER

DOOR / DRAWER

DOOR

5/8" (16)SIDE VIEW

SIDE VIEW

DOOR / DRAWER

5/16" (8) 3/32" (2)

DRAWER

5/32" 5(4) /8" (16)

5/16" DOOR / (8) DRAWER

5/16" (8)

5/16" (8) 35//32 32"" 5/16" (2) (4) (8) 5/8" (16) SIDE VIEW

SIDE VIEW

5/32" (4)

5 SIDE VIEW

5/16" (8)

5/32" 5/16" (4) (8)

5 SIDE VIEW

78

|

Sub-Zero Customer Care 800.222.7820

SIDE VIEW

W INE S T O R AG E

B U I L T- I N

Custom Panel—WS-30 | BW-30

Standard Handles

S I DE PANEL

Optional stainless steel tubular and pro handles are avail­ able through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com.

The custom side panel must be a minimum of 24" (610) deep and 1/2" (13) thick. Routing will be necessary for the side panel to fit flush against the side of the unit. Refer to the illustrations below.

HANDLE LENGTH

TU BU L A R

424G, UW-24 Door

24 1/4"

IW-18, IW-24, IW-30 Door

FRONT OF SIDE PANEL

(616)

(1273)

48 3/8"

(572)

(1229)

IW-30R Door

33 1/4" (845)

31 1/2" (800)

IW-30R Drawer

24 1/4" (616)

22 1/2" (572)

63 7/8" (1622)

45 3/16" (1147)

WS-30, BW-30 Door

24" (610)

50 1/8"

PRO

22 1/4"

1" (25)

1/8" (3) 1/2" (13)

1 7/8"(48) 1" (25)

I N T E G R AT E D

1 7/8" (48)

ROUT TO 1/8" (3)

84"

PRO 48

When installing model WS-30 or BW-30 with a custom side panel, an accessory kit is required. Stainless steel and white enamel side panels are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com.

Refer to the chart below for standard handle lengths for wine storage models.

MAIN FRAME

SIDE PANEL ROUTING

(2134)

Routing detail.

WINE

4" (102) OPTIONAL TOE KICK CUT-OUT

2 5/8" (67)

Side panel dimensions.

|

79

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

W INE S T O R AG E

Wine Rack Wood Facing F ULL-S CALE T E MPL ATE

WOOD FACING WIDTH

PRO 48

The natural cherrywood facing on wine storage racks can be stained and sealed, or replaced with wood more complementary to surrounding cabinetry. Refer to the full-scale template below for profile dimensions of the wood facing and the chart for width.

1/2"

5/8"

(13)

(16)

7/64" (3) 1/4" (6)

27/32"

7/64" (3)

I N T E G R AT E D

(21)

11/2" (38)

27/32" (21)

7/32" (6)

23/64"

23/64"

(9)

9/16" (14)

(9)

5/64" (2)

IW-18, IW-24, IW-30, IW-30R

9/16" (14)

WINE UNDERCOUNTER

|

(2)

424G, UW-24, 424FSG UW-24FS, WS-30, BW-30

Wine rack wood facing profile.

80

5/64"

Sub-Zero Customer Care 800.222.7820

W

424G, UW-24

19 1/2"

424FSG, UW-24FS

19 1/2" (495)

IW-18

11 5/8" (295)

IW-24

17 5/8" (448)

IW-30, IW-30R

23 5/8" (600)

WS-30, BW-30

24 9/16" (624)

(495)

W INE S T O R AG E

B U I L T- I N

Door Clearance—424G | UW-24 F ULL-S CALE T E MPL ATE

To allow for a 145° door opening, the unit should extend a minimum of 1/4" (6) beyond the front surface of adjacent cabinetry. The unit can be installed flush, however, there is potential for interference with the panel if the door is opened past 90°. PRO 48

UNDERCOUNTER UNIT

ADJACENT CABINETRY

I N T E G R AT E D

DOOR CLOSED 1/2"

(13)

3/4" (19) DOOR PANEL 1/4" (6)

1/8" (3)

WINE

HINGE AT 145° OPENING (DOOR OPENS PAST 145°)

1" (25) SCALE

145° door opening (top view).

subzero.com/specs

|

81

UNDERCOUNTER

0"

B U I L T- I N

W INE S T O R AG E

Framed Panel—WS-30 | BW-30

PRO 48

F ULL-S CALE T E MPL ATE

OPTIONAL EXTENDED FULL-LENGTH HANDLE

I N T E G R AT E D

STANDARD FULL-LENGTH HANDLE

2"

1"

(51)

(25)

3"

(76)

11/4" (32) PANEL 1" (25) PANEL 3/4" (19) PANEL 1/2" (13) PANEL

WINE

1/4" (6) FRAMED PANEL

DOOR

UNDERCOUNTER

Framed panel thickness.

82

|

Sub-Zero Customer Care 800.222.7820

W INE S T O R AG E

B U I L T- I N

Overlay | Flush Inset Panels—WS-30 | BW-30 F ULL-S CALE T E MPL ATE

Overlay and flush inset panels must be a minimum of 5/8" (16) thick to support mounting the handle. Panel thickness does not include backer and spacer panel. Mount handle close to the opening edge of the door. PRO 48

DEPTH OF TUBULAR AND PRO HANDLES

2"

(51)

3"

I N T E G R AT E D

1"

(25)

(76)

11/4" (32) PANEL 1" (25) PANEL 3/4" (19) PANEL

.10" (3) SPACER PANEL 1/4" (6) BACKER PANEL

WINE

DOOR

Overlay and flush inset panel thickness.

|

83

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

W INE S T O R AG E

Overlay Application—WS-30 | BW-30 F ULL-S CALE T E MPL ATE 237/8" (606) TO REAR OF UNIT

OVERALL WIDTH OF UNIT

PRO 48

0" (0) 1/4" (6) 1/2" (13) 3/4" (19)

1" (25) 11/4" (32) 11/2" (38) 13/4" (44) I N T E G R AT E D

2" (51) 21/4" (57) 21/2" (63) 23/4" (70) 3" (76) 31/4" (83) 31/2" (89)

WINE

1" (25) THICK PANEL

3/4" (19) THICK OVERLAY PANEL (TYPICAL)

UNDERCOUNTER

1/4" (6) BACKER

PANEL

0"

1" (25) SCALE

90° door opening (top view).

84

|

Sub-Zero Customer Care 800.222.7820

W INE S T O R AG E

B U I L T- I N

Flush Inset Application—WS-30 | BW-30 F ULL-S CALE T E MPL ATE

24" (610) TO BACK WALL

For panels thicker than 3/4" (19), a 90° door stop may be required to prevent interference with adjacent cabinets. 1 1/4" (32) PRO 48

2 3/16" (56) ASSUMES 3/4" (19) FLUSH INSET PANEL THICKNESS

I N T E G R AT E D WINE

1" (25) THICK PANEL

3/4" (19) THICK FLUSH INSET PANEL (TYPICAL)

1/4" (6) BACKER

0"

1" (25) SCALE

110° door opening (top view).

subzero.com/specs

|

85

UNDERCOUNTER

PANEL

B U I L T- I N

W INE S T O R AG E

PRO 48

FILLER STRIP

11/4" (32)

DOOR CLOSED

Dual Standard Installation—WS-30 | BW-30

DOOR OPEN 110°

WINE

I N T E G R AT E D

APPROX PROFILE OF STAINLESS STEEL WRAPPED DOOR AND HANDLE

F ULL-S CALE T E MPL ATE

UNDERCOUNTER

Typical framed, overlay or stainless steel dual installation with filler strip at maximum 110° door opening. Panel thickness may require a 90° door stop.

0"

1" (25) SCALE

Dual standard installation (top view).

86

|

Sub-Zero Customer Care 800.222.7820

W INE S T O R AG E

B U I L T- I N

FILLER STRIP

PRO 48

1 1/2" (38)

1/2" (13)

WINE

Dual Flush Inset Installation—WS-30 | BW-30

DOOR CLOSED

I N T E G R AT E D

PROFILE OF 3/4" (19) FLUSH INSET PANEL AND TUBULAR HANDLE

DOOR OPEN 110°

F ULL-S CALE T E MPL ATE

Typical flush inset dual installation with filler strip at maximum 110° door opening. Panel thickness may require a 90° door stop.

1" (25) SCALE

Dual flush inset installation (top view).

subzero.com/specs

|

87

UNDERCOUNTER

0"

U N DER CO UNT E R RE FRIGE RATION

B U I L T- I N

Undercounter Refrigeration U N D ER C O U N TER MO D ELS

UC-24R

UC-24BG

UC-24C(I)

PRO 48

Sub-Zero undercounter refrigeration is a helpful addition to a master suite, bar, home office or media room. In the kitchen, a high-volume ice machine is a must for entertaining. The design flexibility of these compact yet roomy units makes them all the more welcome in any room or outdoor kitchen. They are ready to be fitted with a custom cabinet panel or can be ordered with a stainless steel panel.

UC-24RO I N T E G R AT E D

I C E MAC H I N E M O D ELS

UC-15I(P)

UC-15I(P)O

WINE

|

89

UNDERCOUNTER

subzero.com/specs

B U I L T- I N

U N DER CO UNT E R RE FRIGE RATION

Overall Dimensions U N DER CO UNT E R

I C E MAC H I N E

23 7/8" (606)

14 3/4" (375)

24" (610)

33 5/8"

34"

PRO 48

23" (584)

(854)

(864)

4" (102)

I N T E G R AT E D

4" (102)

18"

(457)

25 3/8" (645)

6"

(152)

26" (660)

8"

(203)

SPECIFICATIONS

WINE

I NT E R I O R C A PA C I T Y—CU FT (L )

UC-24R, UC-24RO UC-24BG UC-24C(I)

SPECIFICATIONS RE FR

5.7 (161) 6.0 (170) 3.6 (102)

1.1 (31)

SH I P P I N G W E I G H T

L B (KG )

24" Model

130 (59)

Refer to page 97 for door clearance information.

UNDERCOUNTER

FRZR

90

|

Sub-Zero Customer Care 800.222.7820

STORAGE C A PAC ITY

LB ( K G )

UC-15I(P), UC-15I(P)O

26 (12)

SH IP P IN G WEIGH T

LB ( K G )

Ice Machine

100 (45)

Model UC-15I overall dimensions do not include panel or handle.

U N DER CO UNT E R RE FRIGE RATION

B U I L T- I N

Opening Dimensions D U AL I N S TALLATI O N

U N DER CO UNT E R

24" (610) OPENING DEPTH

TOP VIEW

Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero customer care at 800-222-7820.

34 1/2"

W

(876) OPENING HEIGHT

OPENING WIDTH

I N T E G R AT E D

SIDE VIEW

FRONT VIEW

NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry.

3/4" (19)

3/4" (19) TYPICAL

TYPICAL

3 1/2" (89)

3 1/2" (89)

FINISHED RETURN

FINISHED RETURN

W

PRO 48

If two units are installed side by side, a dual installation kit may be required. Installations without a custom filler strip require a dual installation kit. If a dual installation kit is not specified, a 2" (51) filler strip is recommended between units. Dual installations without a filler strip can only be accomplished using two units with opposite hinges. Refer to the illustrations below.

WITHOUT FILLER STRIP

FILLER STRIP

FILLER

Opposite hinges.

Same side hinges.

W FRAMELESS CABINETRY

FRAMED CABINETRY

WINE

OPENING WIDTH

24" Model Ice Machine

W

24" (610) 15 1/4" (387)

DUAL OPENING WIDTH

Two 24" Models

W

48 1/8"

(1222)

subzero.com/specs

|

91

UNDERCOUNTER

Dual installation kit required.

B U I L T- I N

U N DER CO UNT E R RE FRIGE RATION

PRO 48

Electrical The electrical supply should be located within the shaded area shown in the illustrations below. A separate circuit servicing only this appliance is required.

ELECTRICAL REQUIREMENTS

IMPORTANT NOTE: For 24" models, the electrical outlet must be positioned with the grounding prong to the right of the thinner blades.

Receptacle

IMPORTANT NOTE: For outdoor models UC-24RO and UC-15I(P)O, a ground fault circuit interrupter (GFCI) is required to reduce the risk of electrical shock. A GFCI is not recommended for use with other undercounter models and may cause interruption of operation.

Installation must comply with all applicable electrical codes.

I N T E G R AT E D

LEFT SIDE OF OPENING

2"

(51)

LOCATE ELECTRICAL SUPPLY IN ADJACENT CABINET

15 1/2" (394)

3" (76)

E

FLOOR

Ice Machine.

UNDERCOUNTER

WINE

24" Models.

92

|

Sub-Zero Customer Care 800.222.7820

E

Electrical Supply Service

115 VAC, 60 Hz 15 amp dedicated circuit 3-prong grounding-type

U N DER CO UNT E R RE FRIGE RATION

B U I L T- I N

Plumbing

IMPORTANT NOTE: A reverse osmosis system can be used provided there is constant water pressure as indicated in the chart below at all times. A copper line is not recommended for this application.

I C E MAC H I N E D R AI N

Ice machine models can be ordered with or without a drain pump. Models without a pump will drain water by gravity. A drain must be installed. The drain and inlet water tubes must be plumbed before connecting to the ice machine. For the gravity drain, horizontal drain lines must have a 1/4" (6) per 12" (305) fall. An air gap will likely be required between the unit and drain. A stand pipe with a trap below is acceptable for the drain.

PRO 48

The water supply line should be located within the shaded area shown in the illustrations below. The water supply line should be connected to the house supply with an easily accessible shut-off valve between the supply and the unit. Do not use self‑piercing valves. A saddle valve kit is avail­able through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com.

PLUMBING REQUIREMENTS 1/4"

Water Supply Pressure (UC-24CI)

OD copper, braided stainless steel or PEX tubing 20–100 psi (1.4–6.9 bar) 20–80 psi (1.4–5.5 bar)

Excess Line for Connection

I N T E G R AT E D

Pressure (UC-15I)

36" (914)

LEFT SIDE OF OPENING

8"

1/2" (13)

2"

(51)

(203)

24" (610) ROUGH OPENING DEPTH

LOCATION OF WATER LINE

15 1/2" (394)

3" (76)

Model UC-24CI.

WINE

AREA EXTENDS 1/2" (13) FORWARD ON FLOOR

TOP VIEW

Ice machine. 15 1/4" min (387) ROUGH OPENING WIDTH

341/2" (876)

POSITION OUTLET WITH GROUNDING PRONG ON RIGHT

LOCATE ELECTRICAL WITHIN SHADED AREA

MINIMUM HEIGHT REQUIRED

4" (102) FRONT VIEW

subzero.com/specs

|

93

UNDERCOUNTER

ROUGH OPENING HEIGHT 33 5/8" (854)

B U I L T- I N

U N DER CO UNT E R RE FRIGE RATION

Custom Panel For overlay undercounter models, custom door panels and handle hardware must be provided. Refer to the charts for panel requirements and dimensions.

PRO 48

Finish all sides of the custom panels. They may be visible when the door is open or through the window of glass door models. PANEL REQUIREMENTS W E I G H T P E R PA N E L

UC-24R, UC-24C(I) UC-24BG UC-15I(P) PA N E L T H I C K N E S S

UNDERCOUNTER

WINE

I N T E G R AT E D

All Panels

94

|

Sub-Zero Customer Care 800.222.7820

MA X

20 lb (9 kg) 10 lb (5 kg) 15 lb (7 kg) MIN 5/8"

(16)

M O D EL U C -2 4 B G

For model UC-24BG, the custom door panel will attach directly to the door frame with screws through a series of pre-drilled holes. Refer to the illustration below. Do not install a solid panel on a glass door unit. A solid door is available as a sales accessory and must be installed if a solid panel is being specified. Service may be required to install the door. Contact an authorized Sub-Zero dealer for more information. Overall dimensions are the same for glass and solid door panels.

U N DER CO UNT E R RE FRIGE RATION

B U I L T- I N

Custom Panel

Standard Handles

O VER LAY PANEL DIME NSIONS

Optional stainless steel tubular and pro handles are avail­ able through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com.

A

H

A

A

H

Refer to the chart below for standard handle lengths for undercounter models.

A

UC-24R, UC-24C(I), UC-15I(P)

W

UC-24BG

HANDLE LENGTH

TU BU L A R

Undercounter

24 1/4"

Outdoor Model

PRO

(616)

22 1/2"

(572)

NA

15 11/16"

(399)

|

95

PRO 48

W

PANEL DIMENSIONS MODEL

24" Model Ice Machine ST I L E S | R A I L S

UC-24BG

W

H

23 3/4" (603) 15" (381)

30 1/16" (764) 30 3/8" (772) A

2 1/4" (57) min

I N T E G R AT E D

D O O R CLEAR AN CE

Undercounter models can be installed flush with surrounding cabinetry. Depending on the thickness of the custom door panel, it may be necessary to install the unit 1/4" (6) beyond the front surface of adjacent cabinetry to prevent interference when the door is opened to 145°. Refer to the full-scale template on page 97.

WINE UNDERCOUNTER

subzero.com/specs

B U I L T- I N

U N DER CO UNT E R RE FRIGE RATION

Wine Rack Wood Facing F ULL-S CALE T E MPL ATE

WOOD FACING WIDTH

UC-24BG UC-24C(I)

19 1/2" (495)

(495)

PRO 48

The natural cherrywood facing on wine storage racks can be stained and sealed, or replaced with wood more complementary to surrounding cabinetry. Refer to the full-scale template below for profile dimensions of the wood facing and the chart for widths.

W

19 1/2"

1/2"

5/8"

(13)

(16)

7/64" (3) 1/4" (6)

I N T E G R AT E D

27/32"

7/64" (3)

(21)

11/2" (38)

27/32" (21)

23/64"

7/32" (6)

23/64"

(9)

9/16" (14)

IW-18, IW-24, IW-30, IW-30R

(9)

5/64" (2)

9/16" (14)

5/64" (2)

424G, UW-24, 424FSG UW-24FS, WS-30, BW-30

UNDERCOUNTER

WINE

Wine rack wood facing profile.

Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowflake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, Wolf, Wolf & Design, Wolf Gourmet, W & Design, red colored knobs, Cove, and Cove & Design are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries. All other trademarks are property of their respective owners in the United States and other countries.

96

|

Sub-Zero Customer Care 800.222.7820

U N DER CO UNT E R RE FRIGE RATION

B U I L T- I N

Door Clearance—Undercounter F ULL-S CALE T E MPL ATE

To allow for a 145° door opening, the unit should extend a minimum of 1/4" (6) beyond the front surface of adjacent cabinetry. The unit can be installed flush, however, there is potential for interference with the panel if the door is opened past 90°. PRO 48

UNDERCOUNTER UNIT

ADJACENT CABINETRY

I N T E G R AT E D

DOOR CLOSED 1/2"

(13)

3/4" (19) DOOR PANEL 1/4" (6)

1/8" (3)

WINE

HINGE AT 145° OPENING (DOOR OPENS PAST 145°)

1" (25) SCALE

145° door opening (top view).

subzero.com/specs

|

97

UNDERCOUNTER

0"

Sub-Zero Residential Limited Warranty FOR RESIDENTIAL USE FULL TWO YEAR WARRANTY* For two years from the date of original installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, any part of the product that proves to be defective in materials or workmanship. All service provided by Sub-Zero under the above warranty must be performed by Sub-Zero factory certified service, unless otherwise specified by Sub-Zero, Inc. Service will be provided during normal business hours. FULL FIVE YEAR SEALED SYSTEM WARRANTY For five years from the date of original installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, these parts that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. All service provided by Sub-Zero under the above warranty must be performed by Sub-Zero factory certified service, unless otherwise specified by Sub-Zero, Inc. Service will be provided during normal business hours. LIMITED TWELVE YEAR SEALED SYSTEM WARRANTY For twelve years from the date of original installation, Sub-Zero will repair or replace the following parts that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. If the owner uses Sub-Zero factory certified service, the service provider will repair or replace these parts with the owner paying for all other costs, including labor. If the owner uses non-certified service, the owner must contact Sub-Zero, Inc. (using the information below) to receive repaired or replacement parts. Sub-Zero will not reimburse the owner for parts purchased from non-certified service or other sources. TERMS APPLICABLE TO EACH WARRANTY The warranty applies only to products installed for normal residential use. The warranty applies only to products installed in any one of the fifty states of the United States, the District of Columbia or the ten provinces of Canada. This warranty does not cover any parts or labor to correct any defect caused by negligence, accident or improper use, maintenance, installation, service or repair. THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT SUB-ZERO, INC. WILL PROVIDE, EITHER UNDER THIS WARRANTY OR UNDER ANY WARRANTY ARISING BY OPERATION OF LAW. SUB-ZERO, INC. WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM THE BREACH OF THIS WARRANTY OR ANY OTHER WARRANTY, WHETHER EXPRESS, IMPLIED OR STATUTORY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other legal rights that vary from state to state. To receive parts and/or service and the name of Sub-Zero factory certified service nearest you, contact Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744; check the contact & support section of our website, subzero.com, email us at [email protected] or call 800-222-7820. *Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited 60-day parts and labor warranty for cosmetic defects. *Replacement water filters and air purification cartridges are not covered by the product warranty.

Sub-Zero Outdoor Limited Warranty* FOR RESIDENTIAL USE FULL ONE YEAR WARRANTY** For one year from the date of original installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, any part of the product that proves to be defective in materials or workmanship. All service provided by Sub-Zero under the above warranty must be performed by Sub-Zero factory certified service, unless otherwise specified by Sub-Zero, Inc. Service will be provided during normal business hours. FULL FIVE YEAR SEALED SYSTEM WARRANTY For five years from the date of original installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, these parts that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. All service provided by Sub-Zero under the above warranty must be performed by Sub-Zero factory certified service, unless otherwise specified by Sub-Zero, Inc. Service will be provided during normal business hours. TERMS APPLICABLE TO EACH WARRANTY The warranty applies only to products installed for normal residential use. The warranty applies only to products installed in any one of the fifty states of the United States, the District of Columbia or the ten provinces of Canada. This warranty does not cover any parts or labor to correct any defect caused by negligence, accident or improper use, maintenance, installation, service or repair. THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT SUB-ZERO, INC. WILL PROVIDE, EITHER UNDER THIS WARRANTY OR UNDER ANY WARRANTY ARISING BY OPERATION OF LAW. SUB-ZERO, INC. WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM THE BREACH OF THIS WARRANTY OR ANY OTHER WARRANTY, WHETHER EXPRESS, IMPLIED OR STATUTORY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other legal rights that vary from state to state. To receive parts and/or service and the name of Sub-Zero factory certified service nearest you, contact Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744; check the contact & support section of our website, subzero.com, email us at [email protected] or call 800-222-7820. *Product must be approved for outdoor use, designated by model and serial number. **Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited 60-day parts and labor warranty for cosmetic defects. **Replacement water filters are not covered by the product warranty.

SUBZERO.COM