Sunbeam Snow Cone Maker Dasher Replacement
Sunbeam Snow Cone Maker Dasher Replacement
Sunbeam Snow Cone Maker Dasher Replacement Sunbeam Snow Cone Maker Dasher Replacement. The “Dasher” is the spinning plastic piece in the middle. It moves the ice around.
Written By: Thomas Falcon
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
Sunbeam Snow Cone Maker Dasher Replacement
TOOLS: Phillips #00 Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
Sunbeam Snow Cone Maker Dasher Replacement
Step 1 — Dasher
Push the button on the back to release the lid. (Missing on this example device.)
© iFixit — CC BY-NC-SA
www.iFixit.com
In the photo on the device page it is red.
Page 3 of 5
Sunbeam Snow Cone Maker Dasher Replacement
Step 2
Unscrew the dasher by holding it in the middle and turning clockwise.
From here, you can now replace the dasher entirely.
You will have to spin it quite a bit.
Alternately, you can continue to step 3 to further disassemble the dasher components.
To reassemble the device, follow these instructions in reverse order.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 5
Sunbeam Snow Cone Maker Dasher Replacement
Step 3
To take the dasher apart, remove the three 5.5 mm Phillips #00 screws embedded in the plastic. **The 3rd screw is behind the hand in the picture
Carefully pull the two pieces apart.
When you've finished taking apart the dasher, you should have two parts that are shown in the second picture in this step.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-20 04:31:53 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
Sunbeam Snow Cone Maker Dasher Replacement Sunbeam Snow Cone Maker Dasher Replacement. The “Dasher” is the spinning plastic piece in the middle. It moves the ice around.
Written By: Thomas Falcon
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
Sunbeam Snow Cone Maker Dasher Replacement
TOOLS: Phillips #00 Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
Sunbeam Snow Cone Maker Dasher Replacement
Step 1 — Dasher
Push the button on the back to release the lid. (Missing on this example device.)
© iFixit — CC BY-NC-SA
www.iFixit.com
In the photo on the device page it is red.
Page 3 of 5
Sunbeam Snow Cone Maker Dasher Replacement
Step 2
Unscrew the dasher by holding it in the middle and turning clockwise.
From here, you can now replace the dasher entirely.
You will have to spin it quite a bit.
Alternately, you can continue to step 3 to further disassemble the dasher components.
To reassemble the device, follow these instructions in reverse order.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 5
Sunbeam Snow Cone Maker Dasher Replacement
Step 3
To take the dasher apart, remove the three 5.5 mm Phillips #00 screws embedded in the plastic. **The 3rd screw is behind the hand in the picture
Carefully pull the two pieces apart.
When you've finished taking apart the dasher, you should have two parts that are shown in the second picture in this step.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-20 04:31:53 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
