T1023 manual - Displays2go
INSTALLATION MANUAL
Flat Panel Mobile Cart
7. Hanging the TV onto the Universal Plate
P-J P-C P-I
tighten
· Tighten the two screws by using a proper phillips screwdriver to secure the bracket. · Attach the glass shelf to the shelf support using the appropriate screw and washer. Tighten the screw with a proper phillips screwdriver then install the plastic cap.
8. Cable Management
CAUTION: DO NOT EXCEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!
Run the cables through the base and the columns using the cable management holes. Maintenance • Check that the bracket is secure and safe to use at regular intervals(at least every three months). • Please contact your distributor if you have any questions.
200x200 300x300 400x200 400x400 600x400
70" MAX
70kg (154lbs)
TV Stand RATED
ISSUED: AUG. 2013
NOTE: Read the entire instruction manual before you start installation and assembly.
Component Checklist IMPORTANT: Ensure you have received all parts against the component checklist prior to installation. If any parts are missing or faulty, telephone the special franchiser for a replacement.
WARNING • Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor.
glass shelf (x1) A
• This mounting bracket was designed to be installed and utilised ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.
top pipe (x2) E
shelf support (x1) C
shelf support (x1) D
column (x2) G shelf (x1) F
adapter bracket(x2) H
• Always use an assistant or mechanical lifting equipment to safely lift and position the equipment. • Tighten screws firmly, but do not over tighten. Over tightening can cause damage to the items, This greatly reduces their holding power. • This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
shelf support (x1) B
universal plate (x1) I
fixed plate (x1) K
base(x1) J
caster with brake (x2) M
caster (x2) L
Package M
M4x14 (x4) M-A
M4x25 (x4) M-B
M6x25 (x4) M-F
M8x15 (x4) M-G
M5x14 (x4) M-C
M8x30 (x4) M-H
M6x14 (x4) M-E
M5x25 (x4) M-D
washer (x4) M-I
Ø14xØ6x10 Ø15xØ8x15 (x4) (x4) M-J M-K
Package
M6x15 (x4) P-A
plastic bush (x1) P-I
1
M6x20 (x4) P-B
plastic cap (x1) P-J
M5x20 (x1) P-C
M6 (x4) P-K
M6 (x4) P-L
M10x35 (x2) P-D
2.5mm Allen key (x1) P-M
M10x35 (x2) P-E
D6 washer (x 8 ) P-F
2.5mm 4mm Allen key (x1) Allen key (x1) P-N P-O
D10 washer (x2) P-G
5mm Allen key (x1) P-P
foot pad (x4) P-H
8mm Allen key (x1) P-Q
2
3.Installing the Shelf Support and the Base
1.Installing the Casters
Insert and slide the shelf support along the both columns to the desired height, tighten all screws to secure with the 4mm Allen key. M
L G
P-L
J P-E P-L
P-M
Insert the casters into the base holes and tighten the casters to secure. Note: Make sure all casters are in the same height. Note: Lock brakes on casters to avoid sudden movements during installation. P-E
2.Threading the Both Top Pipes into the Shelf P-G P-D
P-M
P-Q
F
Attach the both columns to the base using the appropriate screws and washers, Tighten all screws with the 8mm Allen key.
tighten tighten
P-H E P-O
To adjust the height of shelf, remove the both screws on the pipes to the desired position using the 4mm Allen key.
3
P-N
Insert the feet pad into the arm of shelf support , Align the screw in foot pad with the hole of arm. Tighten all screws using the 2.5mm Allen key.
4
4. Installing the Universal Plate
6. Installing the Adapter Brackets 6-1.For Flat Back Screens
P-P P-B P-F
TV
I
P-K
TV
TV
M-A/M-C/M-E/M-G M-I
Top of the TV P-F P-A P-P
· Attach the fixed plate to the columns at the desired position and secure using the appropriate screws and washers.
· Attach the universal plate to the fixed plate using appropriate screws, washers and nuts.
6-2.For Bump-out or Recessed Back Screens
5. Inserting the Top Pipes (with Attached Shelf ) to the Column TV
TV
TV
M-B/M-D/M-F M-I
M-J
M-H M-I
or
Top of the TV
M-K
Top of the TV
P-O
Tighten all screws with the 4mm Allen key
· Position the adapter brackets as close as possible to the middle of the screen. · Screw the adapter brackets onto the TV. Tighten all screws but do not over tighten.
5
6
Flat Panel Mobile Cart
7. Hanging the TV onto the Universal Plate
P-J P-C P-I
tighten
· Tighten the two screws by using a proper phillips screwdriver to secure the bracket. · Attach the glass shelf to the shelf support using the appropriate screw and washer. Tighten the screw with a proper phillips screwdriver then install the plastic cap.
8. Cable Management
CAUTION: DO NOT EXCEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!
Run the cables through the base and the columns using the cable management holes. Maintenance • Check that the bracket is secure and safe to use at regular intervals(at least every three months). • Please contact your distributor if you have any questions.
200x200 300x300 400x200 400x400 600x400
70" MAX
70kg (154lbs)
TV Stand RATED
ISSUED: AUG. 2013
NOTE: Read the entire instruction manual before you start installation and assembly.
Component Checklist IMPORTANT: Ensure you have received all parts against the component checklist prior to installation. If any parts are missing or faulty, telephone the special franchiser for a replacement.
WARNING • Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor.
glass shelf (x1) A
• This mounting bracket was designed to be installed and utilised ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.
top pipe (x2) E
shelf support (x1) C
shelf support (x1) D
column (x2) G shelf (x1) F
adapter bracket(x2) H
• Always use an assistant or mechanical lifting equipment to safely lift and position the equipment. • Tighten screws firmly, but do not over tighten. Over tightening can cause damage to the items, This greatly reduces their holding power. • This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
shelf support (x1) B
universal plate (x1) I
fixed plate (x1) K
base(x1) J
caster with brake (x2) M
caster (x2) L
Package M
M4x14 (x4) M-A
M4x25 (x4) M-B
M6x25 (x4) M-F
M8x15 (x4) M-G
M5x14 (x4) M-C
M8x30 (x4) M-H
M6x14 (x4) M-E
M5x25 (x4) M-D
washer (x4) M-I
Ø14xØ6x10 Ø15xØ8x15 (x4) (x4) M-J M-K
Package
M6x15 (x4) P-A
plastic bush (x1) P-I
1
M6x20 (x4) P-B
plastic cap (x1) P-J
M5x20 (x1) P-C
M6 (x4) P-K
M6 (x4) P-L
M10x35 (x2) P-D
2.5mm Allen key (x1) P-M
M10x35 (x2) P-E
D6 washer (x 8 ) P-F
2.5mm 4mm Allen key (x1) Allen key (x1) P-N P-O
D10 washer (x2) P-G
5mm Allen key (x1) P-P
foot pad (x4) P-H
8mm Allen key (x1) P-Q
2
3.Installing the Shelf Support and the Base
1.Installing the Casters
Insert and slide the shelf support along the both columns to the desired height, tighten all screws to secure with the 4mm Allen key. M
L G
P-L
J P-E P-L
P-M
Insert the casters into the base holes and tighten the casters to secure. Note: Make sure all casters are in the same height. Note: Lock brakes on casters to avoid sudden movements during installation. P-E
2.Threading the Both Top Pipes into the Shelf P-G P-D
P-M
P-Q
F
Attach the both columns to the base using the appropriate screws and washers, Tighten all screws with the 8mm Allen key.
tighten tighten
P-H E P-O
To adjust the height of shelf, remove the both screws on the pipes to the desired position using the 4mm Allen key.
3
P-N
Insert the feet pad into the arm of shelf support , Align the screw in foot pad with the hole of arm. Tighten all screws using the 2.5mm Allen key.
4
4. Installing the Universal Plate
6. Installing the Adapter Brackets 6-1.For Flat Back Screens
P-P P-B P-F
TV
I
P-K
TV
TV
M-A/M-C/M-E/M-G M-I
Top of the TV P-F P-A P-P
· Attach the fixed plate to the columns at the desired position and secure using the appropriate screws and washers.
· Attach the universal plate to the fixed plate using appropriate screws, washers and nuts.
6-2.For Bump-out or Recessed Back Screens
5. Inserting the Top Pipes (with Attached Shelf ) to the Column TV
TV
TV
M-B/M-D/M-F M-I
M-J
M-H M-I
or
Top of the TV
M-K
Top of the TV
P-O
Tighten all screws with the 4mm Allen key
· Position the adapter brackets as close as possible to the middle of the screen. · Screw the adapter brackets onto the TV. Tighten all screws but do not over tighten.
5
6
