Vornado Flippi V6 Teardown
Vornado Flippi V6 Teardown
Vornado Flippi V6 Teardown Having trouble dismantling the Vornado Flippi V6 fan? This guide shows show you how to disassemble the fan step by step.
Written By: Johnny Tran
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 8
Vornado Flippi V6 Teardown
INTRODUCTION Having trouble dismantling the Vornado Flippi V6 fan? This guide shows show you how to disassemble the fan step by step.
TOOLS: Phillips #1 Screwdriver (1) iFixit Opening Tools (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 8
Vornado Flippi V6 Teardown
Step 1 — Removing the base of fan
Under the base of the fan, remove the four rubber slip guards by peeling them off with your finger tips.
Using the Phillips #1 screwdriver, remove the four 2mm screws underneath the slip guards.
Step 2
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 8
Vornado Flippi V6 Teardown
Step 3
After removing the base of the fan, remove the two screws located under the adjustable speed switch.
Step 4
© iFixit — CC BY-NC-SA
www.iFixit.com
Remove the 4mm screw next to the adjustable speed switch.
Page 4 of 8
Vornado Flippi V6 Teardown
Step 5
Using one hand, pull out the other half of the base.
Remove the four 2mm screws.
Step 6
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 8
Vornado Flippi V6 Teardown
Step 7
Gently pull out the bottom cover.
Step 8
Using two hands, pull the sides out carefully. You will hear a "pop" noise, indicating the sides have came out.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 8
Vornado Flippi V6 Teardown
Step 9
Remove the fan cover using two hands.
Remove the two 2mm screws holding the blades.
Step 10
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 8
Vornado Flippi V6 Teardown
Step 11
To remove the adjustable speed switch cover, slightly pry off 6 clips located around the switch.
This document was last generated on 2017-06-21 07:18:00 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 8 of 8
Vornado Flippi V6 Teardown Having trouble dismantling the Vornado Flippi V6 fan? This guide shows show you how to disassemble the fan step by step.
Written By: Johnny Tran
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 8
Vornado Flippi V6 Teardown
INTRODUCTION Having trouble dismantling the Vornado Flippi V6 fan? This guide shows show you how to disassemble the fan step by step.
TOOLS: Phillips #1 Screwdriver (1) iFixit Opening Tools (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 8
Vornado Flippi V6 Teardown
Step 1 — Removing the base of fan
Under the base of the fan, remove the four rubber slip guards by peeling them off with your finger tips.
Using the Phillips #1 screwdriver, remove the four 2mm screws underneath the slip guards.
Step 2
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 8
Vornado Flippi V6 Teardown
Step 3
After removing the base of the fan, remove the two screws located under the adjustable speed switch.
Step 4
© iFixit — CC BY-NC-SA
www.iFixit.com
Remove the 4mm screw next to the adjustable speed switch.
Page 4 of 8
Vornado Flippi V6 Teardown
Step 5
Using one hand, pull out the other half of the base.
Remove the four 2mm screws.
Step 6
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 8
Vornado Flippi V6 Teardown
Step 7
Gently pull out the bottom cover.
Step 8
Using two hands, pull the sides out carefully. You will hear a "pop" noise, indicating the sides have came out.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 8
Vornado Flippi V6 Teardown
Step 9
Remove the fan cover using two hands.
Remove the two 2mm screws holding the blades.
Step 10
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 8
Vornado Flippi V6 Teardown
Step 11
To remove the adjustable speed switch cover, slightly pry off 6 clips located around the switch.
This document was last generated on 2017-06-21 07:18:00 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 8 of 8
