E4OD, 4R100, C6 - cloudfront.net
E4OD, 4R100, C6
I n s t r u c t i o n D a t a S h e e t
PART NUMBERS 36008B & D, T36008A
Rear Case Bushing & Installation Tool Early Design Style: 3 Grooves to Front
36008B
C6 & E4OD (’89-’94) (Standard OD)
4 Bushings Late Model Design:
3 Grooves to Front, 1 to Back
36008D 4 Bushings
E4OD & 4R100 (’95-Up) (Standard OD)
T36008A 1 Bushing Installation Tool Note: On some C6 applications there may be a ridge of unmachined material which separated the two OEM bushings. This area must be honed down to allow installation.
Bushing Installation Tool
Bushing hardened, steel-backed
Installation Instructions 1. Remove worn or damaged OEM bushings from transmission case. 2. Remove any ridge or case material with a hone if the bore ID is irregular or not center machined. 3. Apply Loctite® sealant to case bore. 4. Align the lubrication hole of the replacement bushing with the hole in the transmission case. 5. It is important to use the Sonnax installation tool T36008A to prevent deformation of the long, thin-walled bushing. In addition, the tool shoulder is designed to seat the bushing at the proper depth. Install the Sonnax bushing with grooves to front. 6. After installing the bushing, confirm that the lubrication holes are properly lined up and that the correct clearance has been maintained between the bushing and output shaft. Sonnax No.
OD
Original OEM Application
36008A
Oversized
C6/Early E4OD
3 grooves to front
36008B
Standard
C6/Early E4OD
3 grooves to front
36008C
Oversized
Late E4OD
3 grooves to front, 1 rear
36008D
Standard
Late E4OD
3 grooves to front, 1 rear
C6/E40D Case
Bushing Installation Tool
Lubrication Groove Configuration Bushing
36008B Rev:-, 36008B(rb)11-10-05
©2005
800-843-2600 • 802-463-9722 • F: 802-463-4059 • www.sonnax.com • [email protected]
1
I n s t r u c t i o n D a t a S h e e t
PART NUMBERS 36008B & D, T36008A
Rear Case Bushing & Installation Tool Early Design Style: 3 Grooves to Front
36008B
C6 & E4OD (’89-’94) (Standard OD)
4 Bushings Late Model Design:
3 Grooves to Front, 1 to Back
36008D 4 Bushings
E4OD & 4R100 (’95-Up) (Standard OD)
T36008A 1 Bushing Installation Tool Note: On some C6 applications there may be a ridge of unmachined material which separated the two OEM bushings. This area must be honed down to allow installation.
Bushing Installation Tool
Bushing hardened, steel-backed
Installation Instructions 1. Remove worn or damaged OEM bushings from transmission case. 2. Remove any ridge or case material with a hone if the bore ID is irregular or not center machined. 3. Apply Loctite® sealant to case bore. 4. Align the lubrication hole of the replacement bushing with the hole in the transmission case. 5. It is important to use the Sonnax installation tool T36008A to prevent deformation of the long, thin-walled bushing. In addition, the tool shoulder is designed to seat the bushing at the proper depth. Install the Sonnax bushing with grooves to front. 6. After installing the bushing, confirm that the lubrication holes are properly lined up and that the correct clearance has been maintained between the bushing and output shaft. Sonnax No.
OD
Original OEM Application
36008A
Oversized
C6/Early E4OD
3 grooves to front
36008B
Standard
C6/Early E4OD
3 grooves to front
36008C
Oversized
Late E4OD
3 grooves to front, 1 rear
36008D
Standard
Late E4OD
3 grooves to front, 1 rear
C6/E40D Case
Bushing Installation Tool
Lubrication Groove Configuration Bushing
36008B Rev:-, 36008B(rb)11-10-05
©2005
800-843-2600 • 802-463-9722 • F: 802-463-4059 • www.sonnax.com • [email protected]
1
