Enchanted Journey II Table runner
Yardage Requirements (based on 42/44” wide fabrics)
Enchanted Journey II Table runner Rust Diamonds Sherbet Ditsy Sherbet Pima Pots Sherbet Kokopelli/Lizards Rust Kokopelli/Lizards Jade Kokopelli/Lizards Jade Ditsy or Baskets Rust Bears Midnight Ditsy Rust or River Aztec Stripe Binding Fabric Backing Fabric
Enchanted Journey II Table runner
3/8 yard 1/4 yard 1/8 yard 1/8 yard 1/4 yard 1/4 yard 1/4 yard 1/4 yard 1/4 yard 3/4 yard 3/8 yard 1 1/2 yard
#110161
Enchanted Journey Batiks designed by Patti Lueker with Southwest Decoratives for Avlyn. Pattern designed by Elizabeth Whitehead.
Come visit us! ©2011 Southwest Decoratives 5711 Carmel Ave NE, Ste B Albuquerque, NM 87113 (505)821-7400 (505)821-6556 Fax (800)530-8995 [email protected] www.swdecoratives.com
Approximate finished size is 26” x 41”
THS PATTERN IS NOT SHAREWARE!
All rights reserved. No part of this pattern may be photocopied or reproduced without written consent from Southwest Decoratives. All finished items produced from this pattern are protected by federal copyright laws and may not be reproduced for commercial use in any form without written consent from Southwest Decoratives.
©2011 Quilt designed by Elizabeth Whitehead with Southwest Decoratives for Avlyn Creations
1/4 yard 1/8 yard 1/8 yard 1/4 yard 1/4 yard 1/4 yard 1/4 yard 1/4 yard 3/4 yard 3/8 yard 1 1/2 yard
Sherbet Ditsy Sherbet Pima Pots Sherbet Kokopelli/Lizards Rust Kokopelli/Lizards Jade Koko/Lizards Jade Baskets Rust Bears Midnight Ditsy River Aztec Stripe* Binding Fabric Backing Fabric
B. C. D. E. F. G. H. I. J. K L.
Draw a diagonal line on the wrong side of fabric B2, center the right side of each fabric B2 square on fabric A2. Sew a 1/4” seam on each side of the drawn line. Cut apart on the drawn line. Trim the A2/B2 to 2 1/4” x 2 1/4” half square triangles. Sew 16 - A2/B2 half square triangles with the angles diagonal to the right. Make 8. Sew 16 - A2/B2 half square triangles with the angles diagonal to the left. Make 8. Sew Fabric A1 to he double A2/B2 units (watch angle) Sew 4 - A2/B2 double units to Fabric C and Sew 4 - A2/B2 double units to Fabric D. Sew 4 - A1-A2/B2 double units to Fabric C and Sew 4 - A1-A2/B2 double units to Fabric D. Assemble 1 complete block with Fabric C and 1 complete block with Fabric D as shown in Figure 7.
Make 2 half blocks as shown using Fabrics E, F, G, & H. Make 4 quarter blocks as shown using Fabrics E, F, G, & H.
Assemble blocks as shown. Trim half blocks and quarter blocks 1/4 inch from point shown. Measure center layout for inner border. Border measurements are approximate. Measure your Tablerunner before cutting. Using Fabric I - cut one 1 1/2” strip in half for the short sides, and use one complete 1 1/2” strip, sew on long sides. Trim. Sew the shorter 1 1/2” strips to the short sides. Using Fabric J, create borders by fussy cutting the strip pattern by cutting 3” long sides first, then cut 3” short sides. Sew short sides first , centering the print on the side. Sew long side matching the print to the short side. Finishing: Layer the Tablerunner top, batting, and backing. Quilt as desired. Trim excess fabric and batting next to Tablerunner. Sew the xxxx 2 1/2” strips (Fabric X) to make one long binding strip. Trim seam allowances to 1/4”. Fold strip in half lengthwise wrong sides together to make one long binding strip. Sew binding strip to the front of the table runner, turn over the edge to the back, pin and hand sew in place.
Fig. 11
Table Runner Layout
Fig. 8 Fig. 9
Quilt Block 2: Single Irish Chain (half and quarter block)
Fig. 7
Fig. 6
Fig. 4 Fig. 5
Fig. 3
Fig. 2
Fig. 1
Quilt Block 1: Bear’s Paw Fig. 2
A2
E
G
E
B2
Fig. 3
F
G
Fig. 8
H
E
C
E
Fig. 4
Quilt Block 1
F
H
G
A2
B2
C
A3
C
E
B2 A2
D
D
Inner Border
Fig. 5
D
B2 A2
D
B2 A2
C
A3
C
A2 B2
A2
A1
A2 B2 A2 B2
B2
A2
A1 B2
Outer Border
Quilt Block 2 (Quarter Block)
A3
B1
A3
A2 B2
A2 A2 B2 B2
E
Quilt Block 1
Trim Lines
E
Fig. 9
B2 A1
A2
A2 B2
Fig. 7 A2 A2 B2 B2
A2 A2 B2 B2
Quilt Block 2 (Half Block)
E
D
A2 A2 B2 B2
Fig. 6
A2 A2 B2 B2
Tablerunner Layout
E
F
E
A2 B2
Fig. 1
A1
Approximate size: 26” x 41”
Tablerunner designed by Southwest Decoratives for Avlyn Creations
Cutting Instructions: A1. 1 - 2 1/4” x WOF strip, sub-cut into 8 - 2 1/4” x 2 1/4” squares A2. 2 - 2 3/4” x WOF strip, sub-cut into 16 - 2 3/4” x 2 3/4” squares A3. 2 - 2 1/4” x WOF strip, sub-cut into 8 - 2 1/4” x 5 3/4” squares B1. 1 - 2 1/4” x WOF strip, sub-cut into 2 - 2 1/4” x 2 1/4” squares B2. 2 - 2 3/4” x WOF strip, sub-cut into 16 - 2 3/4” x 2 3/4” squares C. 1 - 4” x WOF strip, sub-cut into 4 - 4” x 4” squares D. 1 - 4” x WOF strip, sub-cut into 4 - 4” x 4” squares E. 2 - 2 1/2” x WOF strip, sub-cut into 28 - 2 1/2” x 2 1/2” squares F. 2 - 2 1/2” x WOF strip, sub-cut into 8 - 2 1/2” x 8 1/2” rectangles G. 2 - 2 1/2” x WOF strip, sub-cut into 8 - 2 1/2” x 4 1/2” rectangles H. 1 - 4 1/2” x WOF strip, sub-cut into 6 - 4 1/2” x 4 1/2” squares I. 3 - 1 1/2” x WOF strips for inner border J. 2 - 3” x WOF strip for outer border (cut first, centering vertical stripe) 2 - 3” x Length of Fabric (cut second, centering horizontal stripe) K. 4 - 2 1/2” x WOF strip of complementary fabric for binding
Sewing Directions: Note: Use a 1/4” seam allowance throughout unless otherwise indicated. Sew pieces with right sides together and raw edges even with matching thread.
Yardage: 3/8 yard
Fabric Requirements: A. Rust Diamonds
All seam allowances are 1/4”. Please read all directions before beginning and press carefully after each step. Border measurements are approximate, always measure your table runner before cutting border lengths.
Enchanted Journey II Tablerunner
A1 B2
A2 B2 A2
A1
A2 A2 B2 B2
Enchanted Journey II Table runner Rust Diamonds Sherbet Ditsy Sherbet Pima Pots Sherbet Kokopelli/Lizards Rust Kokopelli/Lizards Jade Kokopelli/Lizards Jade Ditsy or Baskets Rust Bears Midnight Ditsy Rust or River Aztec Stripe Binding Fabric Backing Fabric
Enchanted Journey II Table runner
3/8 yard 1/4 yard 1/8 yard 1/8 yard 1/4 yard 1/4 yard 1/4 yard 1/4 yard 1/4 yard 3/4 yard 3/8 yard 1 1/2 yard
#110161
Enchanted Journey Batiks designed by Patti Lueker with Southwest Decoratives for Avlyn. Pattern designed by Elizabeth Whitehead.
Come visit us! ©2011 Southwest Decoratives 5711 Carmel Ave NE, Ste B Albuquerque, NM 87113 (505)821-7400 (505)821-6556 Fax (800)530-8995 [email protected] www.swdecoratives.com
Approximate finished size is 26” x 41”
THS PATTERN IS NOT SHAREWARE!
All rights reserved. No part of this pattern may be photocopied or reproduced without written consent from Southwest Decoratives. All finished items produced from this pattern are protected by federal copyright laws and may not be reproduced for commercial use in any form without written consent from Southwest Decoratives.
©2011 Quilt designed by Elizabeth Whitehead with Southwest Decoratives for Avlyn Creations
1/4 yard 1/8 yard 1/8 yard 1/4 yard 1/4 yard 1/4 yard 1/4 yard 1/4 yard 3/4 yard 3/8 yard 1 1/2 yard
Sherbet Ditsy Sherbet Pima Pots Sherbet Kokopelli/Lizards Rust Kokopelli/Lizards Jade Koko/Lizards Jade Baskets Rust Bears Midnight Ditsy River Aztec Stripe* Binding Fabric Backing Fabric
B. C. D. E. F. G. H. I. J. K L.
Draw a diagonal line on the wrong side of fabric B2, center the right side of each fabric B2 square on fabric A2. Sew a 1/4” seam on each side of the drawn line. Cut apart on the drawn line. Trim the A2/B2 to 2 1/4” x 2 1/4” half square triangles. Sew 16 - A2/B2 half square triangles with the angles diagonal to the right. Make 8. Sew 16 - A2/B2 half square triangles with the angles diagonal to the left. Make 8. Sew Fabric A1 to he double A2/B2 units (watch angle) Sew 4 - A2/B2 double units to Fabric C and Sew 4 - A2/B2 double units to Fabric D. Sew 4 - A1-A2/B2 double units to Fabric C and Sew 4 - A1-A2/B2 double units to Fabric D. Assemble 1 complete block with Fabric C and 1 complete block with Fabric D as shown in Figure 7.
Make 2 half blocks as shown using Fabrics E, F, G, & H. Make 4 quarter blocks as shown using Fabrics E, F, G, & H.
Assemble blocks as shown. Trim half blocks and quarter blocks 1/4 inch from point shown. Measure center layout for inner border. Border measurements are approximate. Measure your Tablerunner before cutting. Using Fabric I - cut one 1 1/2” strip in half for the short sides, and use one complete 1 1/2” strip, sew on long sides. Trim. Sew the shorter 1 1/2” strips to the short sides. Using Fabric J, create borders by fussy cutting the strip pattern by cutting 3” long sides first, then cut 3” short sides. Sew short sides first , centering the print on the side. Sew long side matching the print to the short side. Finishing: Layer the Tablerunner top, batting, and backing. Quilt as desired. Trim excess fabric and batting next to Tablerunner. Sew the xxxx 2 1/2” strips (Fabric X) to make one long binding strip. Trim seam allowances to 1/4”. Fold strip in half lengthwise wrong sides together to make one long binding strip. Sew binding strip to the front of the table runner, turn over the edge to the back, pin and hand sew in place.
Fig. 11
Table Runner Layout
Fig. 8 Fig. 9
Quilt Block 2: Single Irish Chain (half and quarter block)
Fig. 7
Fig. 6
Fig. 4 Fig. 5
Fig. 3
Fig. 2
Fig. 1
Quilt Block 1: Bear’s Paw Fig. 2
A2
E
G
E
B2
Fig. 3
F
G
Fig. 8
H
E
C
E
Fig. 4
Quilt Block 1
F
H
G
A2
B2
C
A3
C
E
B2 A2
D
D
Inner Border
Fig. 5
D
B2 A2
D
B2 A2
C
A3
C
A2 B2
A2
A1
A2 B2 A2 B2
B2
A2
A1 B2
Outer Border
Quilt Block 2 (Quarter Block)
A3
B1
A3
A2 B2
A2 A2 B2 B2
E
Quilt Block 1
Trim Lines
E
Fig. 9
B2 A1
A2
A2 B2
Fig. 7 A2 A2 B2 B2
A2 A2 B2 B2
Quilt Block 2 (Half Block)
E
D
A2 A2 B2 B2
Fig. 6
A2 A2 B2 B2
Tablerunner Layout
E
F
E
A2 B2
Fig. 1
A1
Approximate size: 26” x 41”
Tablerunner designed by Southwest Decoratives for Avlyn Creations
Cutting Instructions: A1. 1 - 2 1/4” x WOF strip, sub-cut into 8 - 2 1/4” x 2 1/4” squares A2. 2 - 2 3/4” x WOF strip, sub-cut into 16 - 2 3/4” x 2 3/4” squares A3. 2 - 2 1/4” x WOF strip, sub-cut into 8 - 2 1/4” x 5 3/4” squares B1. 1 - 2 1/4” x WOF strip, sub-cut into 2 - 2 1/4” x 2 1/4” squares B2. 2 - 2 3/4” x WOF strip, sub-cut into 16 - 2 3/4” x 2 3/4” squares C. 1 - 4” x WOF strip, sub-cut into 4 - 4” x 4” squares D. 1 - 4” x WOF strip, sub-cut into 4 - 4” x 4” squares E. 2 - 2 1/2” x WOF strip, sub-cut into 28 - 2 1/2” x 2 1/2” squares F. 2 - 2 1/2” x WOF strip, sub-cut into 8 - 2 1/2” x 8 1/2” rectangles G. 2 - 2 1/2” x WOF strip, sub-cut into 8 - 2 1/2” x 4 1/2” rectangles H. 1 - 4 1/2” x WOF strip, sub-cut into 6 - 4 1/2” x 4 1/2” squares I. 3 - 1 1/2” x WOF strips for inner border J. 2 - 3” x WOF strip for outer border (cut first, centering vertical stripe) 2 - 3” x Length of Fabric (cut second, centering horizontal stripe) K. 4 - 2 1/2” x WOF strip of complementary fabric for binding
Sewing Directions: Note: Use a 1/4” seam allowance throughout unless otherwise indicated. Sew pieces with right sides together and raw edges even with matching thread.
Yardage: 3/8 yard
Fabric Requirements: A. Rust Diamonds
All seam allowances are 1/4”. Please read all directions before beginning and press carefully after each step. Border measurements are approximate, always measure your table runner before cutting border lengths.
Enchanted Journey II Tablerunner
A1 B2
A2 B2 A2
A1
A2 A2 B2 B2
