Flannel Bunting
m z ie
z ie
Skill Level:
Flannel Bunting
Experience necessary
Crafting Time:
with Optional Swaddle Wrap
Th e
®
®
Th e
Project Instructions
nd of Whi La
Weekend project
Finished Size: 18" x 25 ¼"
La
nd of Whim
Supplies Needed • Land of Whimzie® Woodsie Pal flannel fabric*: 7/8 yd Bunting only 1½ yds Bunting with Swaddle Wrap *Additional yardage required for directional prints • 22" Sweater & jacket coil separating zipper • 1 pkg ¾" Sew-on hook and loop tape • Clear tape • Removable fabric marker • Basic sewing supplies • Sewing machine • Zipper foot • Iron & pressing surface • Serger (optional)
Instructions Read all instructions before beginning project. Do not pre-wash fabrics. Before cutting, press with a dry iron on cotton setting. Use a ½" seam allowance and sew fabrics with right sides together (RST) unless otherwise noted. Finish seams with zigzag or serge stitching and backstitch at beginning and end of seams. Note: When printing pattern pieces, check that page size is set to actual size and compare printout with measurements noted on the patterns. Dia. A
Cutting:
1. Cut out Pattern Pieces on outside lines. Overlap edges of Pattern Pieces so lines match and tape together.
Zipper Placket
4"
24" Place on grain of fabric 24" finished length
Cut 2
Full-Size Pattern for Bunting - Front
(includes ½" seam allowance)
Bunting Front Pattern Piece A
Bunting Front Pattern Piece B
Bunting Front Pattern Piece C
Fold /8 yard
Bunting Back Pattern Piece H
Bunting Back Pattern Piece G
Bunting Back Pattern Piece F
Bunting Back Pattern Piece E
Full-Size Pattern for Bunting - Back Center Front
Cut 1 on fold
19"
(includes ½" seam allowance)
Zipper placket: cut 1 – 3 ½" x 22"
Bunting Front Pattern Piece D
2. Fold fabric as shown with a 4" single layer for Zipper Placket. Lay out Bunting patterns and pin in place. Cut out on solid lines (Dia. A). Transfer Center Front and Lower Front markings to fabric. Lightly press Center Fold in Bunting Back.
25 ½" finished length
place on fold
25½"
7
Finished care instructions: Machine wash, cold, gentle cycle. Tumble dry, low or hang to dry. Not intended for children’s sleepwear.
Page 1 of 13 ©2016 Fabric Editions, Inc. Land of Whimzie® is a trademark of Fabric Editions, Inc.
Project Instructions Continued Swaddle Wrap Option: Cut 2 – 9 ½" x 14 ½" (on fold) Unfold pieces and layer on top of each other. Place Swaddle Wrap pattern as shown to cut curved ends (Dia. B).
Dia. B Hook and loop tape: cut 2 – ¾" x 6" Dia. B
29" Match to top/bottom edge
Match to top/bottom edge
29" Match to short edge and cut shape
Match to short edge and cut shape
Full-Size Pattern for Swaddle Wrap
Cut 2 (1 for each end)
Full-Size Pattern for Swaddle Wrap
Cut 2 (1 for each end)
Match to top/bottom edge
Match to top/bottom edge
Full-Size Pattern for Swaddle Wrap
Cut 2 (1 for each end)
Match to top/bottom edge
Full-Size Pattern for Swaddle Wrap
9 ½"
9 ½" x 14 ½"
Match to short edge and cut shape
9 ½" x 14 ½"
Cut 2 (1 for each end)
9 ½"
9 ½" x 14 ½"
Match to short edge and cut shape
9 ½" x 14 ½"
Match to top/bottom edge
Match to top/bottom edge
Match to top/bottom edge
Fold 5 /8 yard Fold 5 /8 yard
Sewing:
1. Finish all edges of Bunting Front and Back except neckline and arm holes, with serging or zigzag stitching. 2. Pin and sew shoulders RST (Dia. C); press seams open. Dia. D
Dia. C Back (RS) Sew
Sew
Front (wrong side)
Front (wrong side)
Front (wrong side)
Front (wrong side)
Sew Sew
3. Fold and press the edge of the armholes and neck ¼" to the wrong side twice; sew close to folded edge to hem (Dia. D).
Sew
Back (wrong side)
Page 2 of 13
Project Instructions Continued 4. Place Fronts RST. Sew from bottom edge to mark; backstitch. Baste, using longest stitch length, from mark to top edge. Press seam open (Dia. E). 5. Fold Zipper Placket (3 ½" x 22") RST so long edges meet; sew using ¼" seam around cut edges, leaving a 3" opening for turning. Trim corners diagonally and turn right side out; press (Dia. F). Hand stitch opening closed.
Dia. E
Dia. F
3" opening
Trim Baste
6. To cut zipper to the correct length, measure up 21 ½" from the zipper bottom and make a mark. Pull zipper tab down 3" and cut zipper off at mark. Measure down 1" from the cut edge and make another mark (Dia. G).
Front (wrong side)
1"
Dia. G 21 ½"
Cut line
Sew to dot
7. Lay Bunting Front wrong side up on a flat surface. Place zipper with the right side down on Front center seam with zipper bottom about ¼" from the neckline. Center the zipper teeth along the basted seam and pin. Baste in center of zipper tape and across the end using a zipper foot (Dia. H). Note: The zipper opening will be at the bottom of the Bunting, so the zipper pull is at the bottom. 8. Turn Bunting over to sew zipper in place from right side. Begin at the neckline and sew ¼" from folded edges around zipper and back to neckline, stopping to move zipper tab while sewing. Note: A few basting stitches will need to be removed. Dia. H
Baste edges of zipper tape
Bottom of zipper
9. With Bunting Front wrong side up, place short edge of Zipper Placket even with bottom end of zipper (at neckline) and long folded edge even with right zipper tape; baste through all layers along side and across bottom (Dia. I). With the right side of Bunting Front facing up, sew over basting to attach placket. Dia. I
Baste & sew
Zipper placket
Bottom of zipper
Page 3 of 13
Project Instructions Continued 10. Pin side seams RST and sew from one underarm edge to the other. Press seams open.
Optional Swaddle Wrap:
Dia. J
11. Pin Swaddle Wrap pieces RST and use a ¼" seam allowance to sew leaving a 4" opening on a straight edge for turning. Clip curves and turn right side out; press and hand stitch opening closed. Topstitch ¼" away from outer edge. Swaddle Wrap should measure 9" x 28 ½". 12. With the bottom edge of the Swaddle Wrap toward you, fold the Swaddle Wrap so curved edges meet to find the center and draw a center line with the removable marker across the width. Along the center crease of the back, mark 2 ¾" down from neckline. Pin the Swaddle Wrap to the Bunting Back with the top of the center line matching the drawn mark. Measure 4 ¼" on both sides of the center line and use a removable marker to draw straight sewing lines. Sew along lines through Wrap and Bunting Back (only) to attach (Dia. J).
Center crease
Center line
2 ¾"
4 ¼"
4 ¼"
Sewing lines
Center crease
13. Place Bunting with Front side up on flat surface and extend the right end of Swaddle Wrap out to the side. Measure 3" from the seam and down 2" from the top edge; mark. Pin the hook tape (rough side) to Swaddle at mark. Repeat with the loop tape (soft side) on the back side of the left Swaddle. Check that they line up and sew around edges (Dia. K). Repeat with the second hook and loop tape piece, measuring 1 ½" from the seam and 2" from the bottom edge.
Dia. K
Hook & Loop Tape (soft side) Place 2 ½" from seam; 2" from top edge Place 1 ½" from seam; 2" from bottom edge
Hook & Loop Tape (rough side) Place 2 ½" from seam; 2" from top edge Place 1 ½" from seam; 2" from bottom edge
Page 4 of 13
Bunting Front Pattern Piece A
Cut 2
(includes ½" seam allowance)
Full-Size Pattern for Bunting - Front
Project Instructions Continued
Page 5 of 13
Bunting Front Pattern Piece B
Overlap with Pattern Piece A
Project Instructions Continued
Page 6 of 13
Bunting Front Pattern Piece C
Overlap with Pattern Piece B
Project Instructions Continued
Place on grain of fabric 24" finished length Page 7 of 13
2 ½" from bottom edge
Bunting Front Pattern Piece D
Overlap with Pattern Piece C
Project Instructions Continued
Page 8 of 13
Bunting Back Pattern Piece E
Cut 1 on fold
(includes ½" seam allowance)
Full-Size Pattern for Bunting - Back
Project Instructions Continued
Center Front
Page 9 of 13
Bunting Back Pattern Piece F
Overlap with Pattern Piece E
Project Instructions Continued
Place on fold
Page 10 of 13
Bunting Back Pattern Piece G
Overlap with Pattern Piece F
Project Instructions Continued
Place on grain of fabric 25 ½" finished length
Page 11 of 13
Bunting Back Pattern Piece H
Overlap with Pattern Piece G
Project Instructions Continued
Page 12 of 13
Project Instructions Continued
Cut 2 (1 for each end)
Full-Size Pattern for Swaddle Wrap
Match to top/bottom edge Match to short edge and cut shape
Match to top/bottom edge Page 13 of 13
z ie
Skill Level:
Flannel Bunting
Experience necessary
Crafting Time:
with Optional Swaddle Wrap
Th e
®
®
Th e
Project Instructions
nd of Whi La
Weekend project
Finished Size: 18" x 25 ¼"
La
nd of Whim
Supplies Needed • Land of Whimzie® Woodsie Pal flannel fabric*: 7/8 yd Bunting only 1½ yds Bunting with Swaddle Wrap *Additional yardage required for directional prints • 22" Sweater & jacket coil separating zipper • 1 pkg ¾" Sew-on hook and loop tape • Clear tape • Removable fabric marker • Basic sewing supplies • Sewing machine • Zipper foot • Iron & pressing surface • Serger (optional)
Instructions Read all instructions before beginning project. Do not pre-wash fabrics. Before cutting, press with a dry iron on cotton setting. Use a ½" seam allowance and sew fabrics with right sides together (RST) unless otherwise noted. Finish seams with zigzag or serge stitching and backstitch at beginning and end of seams. Note: When printing pattern pieces, check that page size is set to actual size and compare printout with measurements noted on the patterns. Dia. A
Cutting:
1. Cut out Pattern Pieces on outside lines. Overlap edges of Pattern Pieces so lines match and tape together.
Zipper Placket
4"
24" Place on grain of fabric 24" finished length
Cut 2
Full-Size Pattern for Bunting - Front
(includes ½" seam allowance)
Bunting Front Pattern Piece A
Bunting Front Pattern Piece B
Bunting Front Pattern Piece C
Fold /8 yard
Bunting Back Pattern Piece H
Bunting Back Pattern Piece G
Bunting Back Pattern Piece F
Bunting Back Pattern Piece E
Full-Size Pattern for Bunting - Back Center Front
Cut 1 on fold
19"
(includes ½" seam allowance)
Zipper placket: cut 1 – 3 ½" x 22"
Bunting Front Pattern Piece D
2. Fold fabric as shown with a 4" single layer for Zipper Placket. Lay out Bunting patterns and pin in place. Cut out on solid lines (Dia. A). Transfer Center Front and Lower Front markings to fabric. Lightly press Center Fold in Bunting Back.
25 ½" finished length
place on fold
25½"
7
Finished care instructions: Machine wash, cold, gentle cycle. Tumble dry, low or hang to dry. Not intended for children’s sleepwear.
Page 1 of 13 ©2016 Fabric Editions, Inc. Land of Whimzie® is a trademark of Fabric Editions, Inc.
Project Instructions Continued Swaddle Wrap Option: Cut 2 – 9 ½" x 14 ½" (on fold) Unfold pieces and layer on top of each other. Place Swaddle Wrap pattern as shown to cut curved ends (Dia. B).
Dia. B Hook and loop tape: cut 2 – ¾" x 6" Dia. B
29" Match to top/bottom edge
Match to top/bottom edge
29" Match to short edge and cut shape
Match to short edge and cut shape
Full-Size Pattern for Swaddle Wrap
Cut 2 (1 for each end)
Full-Size Pattern for Swaddle Wrap
Cut 2 (1 for each end)
Match to top/bottom edge
Match to top/bottom edge
Full-Size Pattern for Swaddle Wrap
Cut 2 (1 for each end)
Match to top/bottom edge
Full-Size Pattern for Swaddle Wrap
9 ½"
9 ½" x 14 ½"
Match to short edge and cut shape
9 ½" x 14 ½"
Cut 2 (1 for each end)
9 ½"
9 ½" x 14 ½"
Match to short edge and cut shape
9 ½" x 14 ½"
Match to top/bottom edge
Match to top/bottom edge
Match to top/bottom edge
Fold 5 /8 yard Fold 5 /8 yard
Sewing:
1. Finish all edges of Bunting Front and Back except neckline and arm holes, with serging or zigzag stitching. 2. Pin and sew shoulders RST (Dia. C); press seams open. Dia. D
Dia. C Back (RS) Sew
Sew
Front (wrong side)
Front (wrong side)
Front (wrong side)
Front (wrong side)
Sew Sew
3. Fold and press the edge of the armholes and neck ¼" to the wrong side twice; sew close to folded edge to hem (Dia. D).
Sew
Back (wrong side)
Page 2 of 13
Project Instructions Continued 4. Place Fronts RST. Sew from bottom edge to mark; backstitch. Baste, using longest stitch length, from mark to top edge. Press seam open (Dia. E). 5. Fold Zipper Placket (3 ½" x 22") RST so long edges meet; sew using ¼" seam around cut edges, leaving a 3" opening for turning. Trim corners diagonally and turn right side out; press (Dia. F). Hand stitch opening closed.
Dia. E
Dia. F
3" opening
Trim Baste
6. To cut zipper to the correct length, measure up 21 ½" from the zipper bottom and make a mark. Pull zipper tab down 3" and cut zipper off at mark. Measure down 1" from the cut edge and make another mark (Dia. G).
Front (wrong side)
1"
Dia. G 21 ½"
Cut line
Sew to dot
7. Lay Bunting Front wrong side up on a flat surface. Place zipper with the right side down on Front center seam with zipper bottom about ¼" from the neckline. Center the zipper teeth along the basted seam and pin. Baste in center of zipper tape and across the end using a zipper foot (Dia. H). Note: The zipper opening will be at the bottom of the Bunting, so the zipper pull is at the bottom. 8. Turn Bunting over to sew zipper in place from right side. Begin at the neckline and sew ¼" from folded edges around zipper and back to neckline, stopping to move zipper tab while sewing. Note: A few basting stitches will need to be removed. Dia. H
Baste edges of zipper tape
Bottom of zipper
9. With Bunting Front wrong side up, place short edge of Zipper Placket even with bottom end of zipper (at neckline) and long folded edge even with right zipper tape; baste through all layers along side and across bottom (Dia. I). With the right side of Bunting Front facing up, sew over basting to attach placket. Dia. I
Baste & sew
Zipper placket
Bottom of zipper
Page 3 of 13
Project Instructions Continued 10. Pin side seams RST and sew from one underarm edge to the other. Press seams open.
Optional Swaddle Wrap:
Dia. J
11. Pin Swaddle Wrap pieces RST and use a ¼" seam allowance to sew leaving a 4" opening on a straight edge for turning. Clip curves and turn right side out; press and hand stitch opening closed. Topstitch ¼" away from outer edge. Swaddle Wrap should measure 9" x 28 ½". 12. With the bottom edge of the Swaddle Wrap toward you, fold the Swaddle Wrap so curved edges meet to find the center and draw a center line with the removable marker across the width. Along the center crease of the back, mark 2 ¾" down from neckline. Pin the Swaddle Wrap to the Bunting Back with the top of the center line matching the drawn mark. Measure 4 ¼" on both sides of the center line and use a removable marker to draw straight sewing lines. Sew along lines through Wrap and Bunting Back (only) to attach (Dia. J).
Center crease
Center line
2 ¾"
4 ¼"
4 ¼"
Sewing lines
Center crease
13. Place Bunting with Front side up on flat surface and extend the right end of Swaddle Wrap out to the side. Measure 3" from the seam and down 2" from the top edge; mark. Pin the hook tape (rough side) to Swaddle at mark. Repeat with the loop tape (soft side) on the back side of the left Swaddle. Check that they line up and sew around edges (Dia. K). Repeat with the second hook and loop tape piece, measuring 1 ½" from the seam and 2" from the bottom edge.
Dia. K
Hook & Loop Tape (soft side) Place 2 ½" from seam; 2" from top edge Place 1 ½" from seam; 2" from bottom edge
Hook & Loop Tape (rough side) Place 2 ½" from seam; 2" from top edge Place 1 ½" from seam; 2" from bottom edge
Page 4 of 13
Bunting Front Pattern Piece A
Cut 2
(includes ½" seam allowance)
Full-Size Pattern for Bunting - Front
Project Instructions Continued
Page 5 of 13
Bunting Front Pattern Piece B
Overlap with Pattern Piece A
Project Instructions Continued
Page 6 of 13
Bunting Front Pattern Piece C
Overlap with Pattern Piece B
Project Instructions Continued
Place on grain of fabric 24" finished length Page 7 of 13
2 ½" from bottom edge
Bunting Front Pattern Piece D
Overlap with Pattern Piece C
Project Instructions Continued
Page 8 of 13
Bunting Back Pattern Piece E
Cut 1 on fold
(includes ½" seam allowance)
Full-Size Pattern for Bunting - Back
Project Instructions Continued
Center Front
Page 9 of 13
Bunting Back Pattern Piece F
Overlap with Pattern Piece E
Project Instructions Continued
Place on fold
Page 10 of 13
Bunting Back Pattern Piece G
Overlap with Pattern Piece F
Project Instructions Continued
Place on grain of fabric 25 ½" finished length
Page 11 of 13
Bunting Back Pattern Piece H
Overlap with Pattern Piece G
Project Instructions Continued
Page 12 of 13
Project Instructions Continued
Cut 2 (1 for each end)
Full-Size Pattern for Swaddle Wrap
Match to top/bottom edge Match to short edge and cut shape
Match to top/bottom edge Page 13 of 13
