FloodPak 10 pg - Stonco Lighting
Architectural Floodlight
Patented
Stonco is a Philips group brand
One Fixture, Three Distributions, Unlimited Lighting Possibilities
S
tonco’s new FloodPak® is the ultimate in exterior lighting versatility. It is the perfect blend of performance, flexibility and architectural design. The FloodPak® is three fixtures in one! It’s a high-performance cutoff luminaire for perimeter and site lighting. Rotate it 22.5° and it’s a semi-cutoff luminaire offering forward throw. Rotate it to 45° for floodlighting or turn it over to create indirect/accent lighting—the possibilities are endless.
Lowest Installed Cost 1) Fewer Fixtures Required When mounted at 0 degrees, the FloodPak® offers a wide Type II distribution with a spacing ratio of up to 6:1. This permits greater spacing between fixtures than conventional wallpack luminaires. Fewer fixtures equals lower cost. 2) Reduced Installation Time The FloodPak® features quick and easy installation. By design, the FloodPak® installs in half the time as compared with conventional surface and pole mounted lighting products. Faster installation translates into lower labor costs. 3) Less Energy Consumed Because fewer FloodPaks are required, less energy is consumed. Less energy results in lower operation costs.
Cutoff Complies with local Dark Sky requirements.
Forward Throw DayForm styling provides consistency in multiple applications. Surface Mount Quickly adjusts to different lighting requirements.
Indirect Lighting Maximum versatility from a single outdoor fixture.
Facade Lighting Ground mounted for above-horizontal aiming.
Site Lighting Pole mounted using shoebox-style arm accessory.
Designed to Meet Today’s Lighting Challenges Greater Efficiency than Traditional Wallpacks With conventional wallpacks, up to 70% of the available light never reaches its destination. Approximately 40% is lost within the fixture, while an additional 30% is directed outward and upward above 90°. The FloodPak’s high performance places 80% of the available light down and out where it is needed resulting in fewer fixtures, better lighting and greater savings.
Conventional WallPack
Meets Dark Sky and Light Trespass Requirements The FloodPak® cutoff luminaire is designed around a high-performance, multifaceted optical system that meets today’s strict IESNA Dark Sky requirements. When mounted at 0° the FloodPak® directs all of the light below 90° reducing glare and ensuring compliance to local “Dark Sky” codes. Tipping the FloodPak® up 22.5° redirects the light forward allowing control over light trespass issues.
A Family of Fixtures The FloodPak® family is available in three sizes ranging from 70 thru 400 watts. The three distinct sizes ensure correct proportional relationship and architectural DayForm styling that complements most applications.
FloodPak®
Full Cutoff
FloodPak® @ 0˚ Full Cutoff Photometry FPS150NLXL-1
Mounting Ht. 15’
FPM175MAL-8
Mounting Ht. 15’
FPL400MAL-8
When wall-mounted in the 0° position, the FloodPak® replaces a standard wallpack fixture for use in perimeter and security lighting. The IESNA-rated cutoff optics provide wide distribution with up to 6:1 spacing ratio for maximum distance between fixtures, while meeting stringent Dark Sky requirements. The FloodPak® can also be pole mounted for use in site and area lighting with an optional arm, or it can be rotated 180° for dramatic wall-washing effects.
Wall Wash Indirect
Site Lighting
Mounting Ht. 15’
WATTAGE 50 70 100 150
MULTIPLIER 0.25 0.4 0.59 1
MTG HT 8 10 15 20
MULTIPLIER 3.5 2.3 1 0.6
FloodPak® Features and Benefits Rugged Construction
Precision die-cast aluminum housing, door frame and mounting box.
Duraplex-II Polyester Powder Finish
Dark bronze standard. Other designer colors available.
DayForm Appearance
Stylized daytime architectural design.
Injection Molded Silicon Gasket
Triple-finger seal prevents leakage in any position.
Easy Access
Hinged door includes clear non-yellowing tempered glass lens.
Support Cable
Permits easy hands-free wiring.
Integral Heat Sink
Ensures cool operation and longer ballast life.
Multifaceted Reflector Delivers uniform illumination in all positions.
VandalResistant
Captive and tamperresistant screws.
Corrosion-Resistant Hardware
All exposed hardware made from stainless steel.
Mounting/Wiring Box
Rated for 90°C supply wire. Can be surface mounted over various recess boxes or accept ½” conduit. Also accepts a button photocontrol.
Integral Bubble Level
Fast positioning of mounting bracket.
cUL Listed for Wet Locations
Approved for above and below horizontal aiming. Covered under multiple patents
Semi-Cutoff
FloodPak® @ 22.5˚ Semi-Cutoff Photometry FPS150NLXL-1
FPM175MAL-8
Mounting Ht. 15’
Mounting Ht. 15’
FPL400MAL-8
Rotating the fixture body to its 22.5° position converts the FloodPak® to semi-cutoff optics with forward-throw distribution resulting in up to 5:1 spacing ratio. When pole mounted at the 22.5° angle, light is directed away from the pole base for greater coverage. It can also be ground mounted for above horizontal aiming and indirect lighting.
Mounting Ht. 15’
WATTAGE 70 100 150 175 MTG HT 8 10 15 20
Pole Mounted
Indirect Lighting
MULTIPLIER 0.36 0.57 0.7 1 MULTIPLIER 3.5 2.3 1 0.6
Flood
FloodPak® @ 45˚ Flood Photometry FPS150NLXL-1
Mounting Ht. 15’
FPM175MAL-8
Mounting Ht. 15’
FPL400MAL-8
Rotated in the 45° position, the FloodPak® transforms into an allpurpose flood for general lighting. It produces a NEMA 7 x 6 light distribution pattern for applications requiring a wide-beam pattern. In addition to above and below horizontal surface mounting, the FloodPak® can be pole mounted as a high-angle flood or ground mounted for facade and accent lighting.
Flood Lighting
Facade Lighting
Mounting Ht. 15’
WATTAGE 250 MH 250 HPS 400 HPS 400 MH
MULTIPLIER 0.57 0.79 1.39 1
MTG HT 15 20 25 30
MULTIPLIER 1.78 1 0.64 0.44
Contractor Friendly Thinking Outside the Box
Stonco developed its packaging to be user friendly for fixture selection and ease of installation.
Flexible Installation
The FloodPak® can be mounted using through-wall wiring or surface-mount ½” conduit.
Stonco is Always on the Level
An auto leveling device is part of every FloodPak® mounting box. Just rotate the box in position on the wall until level and then anchor securely.
UL Approved Splice Box
The isolated mounting box allows the contractor to use 90˚C supply wire.
Hands-Free Wiring
An integral cable holds the fixture to the installed mounting box, permitting easy hands-free wiring and single-person installation.
Specifications FloodPak® Configurations
O˚ Down
22.5˚ Down
45˚ Down
0˚ Up
22.5˚ Up
45˚ Up
Ordering Logic FPS
150
NLX
L
1
SERIES
WATTAGE
LAMP SOURCE
LAMP
VOLTAGE
L= Lamp Furnished
1=120
FPS 42 NLX=High Pressure Sodium (NPF) 70 HFL=Compact Fluorescent 100 150 HID units supplied with clear medium base lamp.
FPM
175
MA
L
8
SERIES
WATTAGE
LAMP SOURCE
LAMP
VOLTAGE
FPM 70 MA=Metal Halide (CWA) L= Lamp 100 LX=High Pressure Sodium (HX-HPF) Furnished 150 PMA=Pulse Start Metal Halide (HX-HPF) 175 HID units supplied with clear medium base lamp.
1=120 5=480 8=120/ 208 240/277
FPL
400
MA
L
8
SERIES
WATTAGE
LAMP SOURCE
LAMP
VOLTAGE
FPL 250 MA=Metal Halide (CWA) L= Lamp 400* LX=High Pressure Sodium (CWA) Furnished Supplied with clear mogul base lamp. *Requires reduced outer jacketed lamp.
Dimensional Data FPS
EPA = 0.67 sq. ft.
FPL
FPM
EPA = 0.89 sq. ft.
EPA = 1.68 sq. ft.
1=120 5=480 8=120/208/ 240/277
FloodPak® Accessories FPLARM Shoebox arm-converts FPL Series FloodPak® to pole mount (minimum 4”square pole). Use FPLRPA for mounting FPLARM to a 4” round pole.
FPSARM Shoebox arm converts FPS/FPM Series FloodPak® to pole mount (minimum 4” square). FPS and FPM onlyuse FPSRPA for mounting FPSARM to a 4” round pole.
FPLKNUCKLE Adjustable 2” Tenon Slipfitter (FPL Series only).
FPSKNUCKLE 1/2” Adjustable Knuckle (FPS and FPM Series only).
FPSSHIELD FPMSHIELD FPLSHIELD Vandal Shield - Helps protect lens and lamp from breakage. Clear polycarbonate shield snaps in place over glass lens.
FPSRPA 4” Round pole adapter for use with FPSARM. FPLRPA 4” Round pole adapter for use with FPLARM.
These mounting accessories are designed to be used with the standard FloodPak® mounting hardware (above) to adapt the luminaire to other mounting applications.
2” Pipe and Concrete Pad Applications PMAS Pipe Adapter for Small and Medium PMAL Pipe Adapter for Large
Retrofit Applications WMAS Wall-Mounting Adapter for Small and Medium
Photo Control P110A - External 120V Control P105A - Button 120v Control
2345 Vauxhall Road Union, NJ 07083 1-800-334-2212 www.FloodPak.com www.stoncolighting.com
Printed on recycled paper Minimum 10% post-consumer Printed in U.S.A. SFPBRO508-10
Patented
Stonco is a Philips group brand
One Fixture, Three Distributions, Unlimited Lighting Possibilities
S
tonco’s new FloodPak® is the ultimate in exterior lighting versatility. It is the perfect blend of performance, flexibility and architectural design. The FloodPak® is three fixtures in one! It’s a high-performance cutoff luminaire for perimeter and site lighting. Rotate it 22.5° and it’s a semi-cutoff luminaire offering forward throw. Rotate it to 45° for floodlighting or turn it over to create indirect/accent lighting—the possibilities are endless.
Lowest Installed Cost 1) Fewer Fixtures Required When mounted at 0 degrees, the FloodPak® offers a wide Type II distribution with a spacing ratio of up to 6:1. This permits greater spacing between fixtures than conventional wallpack luminaires. Fewer fixtures equals lower cost. 2) Reduced Installation Time The FloodPak® features quick and easy installation. By design, the FloodPak® installs in half the time as compared with conventional surface and pole mounted lighting products. Faster installation translates into lower labor costs. 3) Less Energy Consumed Because fewer FloodPaks are required, less energy is consumed. Less energy results in lower operation costs.
Cutoff Complies with local Dark Sky requirements.
Forward Throw DayForm styling provides consistency in multiple applications. Surface Mount Quickly adjusts to different lighting requirements.
Indirect Lighting Maximum versatility from a single outdoor fixture.
Facade Lighting Ground mounted for above-horizontal aiming.
Site Lighting Pole mounted using shoebox-style arm accessory.
Designed to Meet Today’s Lighting Challenges Greater Efficiency than Traditional Wallpacks With conventional wallpacks, up to 70% of the available light never reaches its destination. Approximately 40% is lost within the fixture, while an additional 30% is directed outward and upward above 90°. The FloodPak’s high performance places 80% of the available light down and out where it is needed resulting in fewer fixtures, better lighting and greater savings.
Conventional WallPack
Meets Dark Sky and Light Trespass Requirements The FloodPak® cutoff luminaire is designed around a high-performance, multifaceted optical system that meets today’s strict IESNA Dark Sky requirements. When mounted at 0° the FloodPak® directs all of the light below 90° reducing glare and ensuring compliance to local “Dark Sky” codes. Tipping the FloodPak® up 22.5° redirects the light forward allowing control over light trespass issues.
A Family of Fixtures The FloodPak® family is available in three sizes ranging from 70 thru 400 watts. The three distinct sizes ensure correct proportional relationship and architectural DayForm styling that complements most applications.
FloodPak®
Full Cutoff
FloodPak® @ 0˚ Full Cutoff Photometry FPS150NLXL-1
Mounting Ht. 15’
FPM175MAL-8
Mounting Ht. 15’
FPL400MAL-8
When wall-mounted in the 0° position, the FloodPak® replaces a standard wallpack fixture for use in perimeter and security lighting. The IESNA-rated cutoff optics provide wide distribution with up to 6:1 spacing ratio for maximum distance between fixtures, while meeting stringent Dark Sky requirements. The FloodPak® can also be pole mounted for use in site and area lighting with an optional arm, or it can be rotated 180° for dramatic wall-washing effects.
Wall Wash Indirect
Site Lighting
Mounting Ht. 15’
WATTAGE 50 70 100 150
MULTIPLIER 0.25 0.4 0.59 1
MTG HT 8 10 15 20
MULTIPLIER 3.5 2.3 1 0.6
FloodPak® Features and Benefits Rugged Construction
Precision die-cast aluminum housing, door frame and mounting box.
Duraplex-II Polyester Powder Finish
Dark bronze standard. Other designer colors available.
DayForm Appearance
Stylized daytime architectural design.
Injection Molded Silicon Gasket
Triple-finger seal prevents leakage in any position.
Easy Access
Hinged door includes clear non-yellowing tempered glass lens.
Support Cable
Permits easy hands-free wiring.
Integral Heat Sink
Ensures cool operation and longer ballast life.
Multifaceted Reflector Delivers uniform illumination in all positions.
VandalResistant
Captive and tamperresistant screws.
Corrosion-Resistant Hardware
All exposed hardware made from stainless steel.
Mounting/Wiring Box
Rated for 90°C supply wire. Can be surface mounted over various recess boxes or accept ½” conduit. Also accepts a button photocontrol.
Integral Bubble Level
Fast positioning of mounting bracket.
cUL Listed for Wet Locations
Approved for above and below horizontal aiming. Covered under multiple patents
Semi-Cutoff
FloodPak® @ 22.5˚ Semi-Cutoff Photometry FPS150NLXL-1
FPM175MAL-8
Mounting Ht. 15’
Mounting Ht. 15’
FPL400MAL-8
Rotating the fixture body to its 22.5° position converts the FloodPak® to semi-cutoff optics with forward-throw distribution resulting in up to 5:1 spacing ratio. When pole mounted at the 22.5° angle, light is directed away from the pole base for greater coverage. It can also be ground mounted for above horizontal aiming and indirect lighting.
Mounting Ht. 15’
WATTAGE 70 100 150 175 MTG HT 8 10 15 20
Pole Mounted
Indirect Lighting
MULTIPLIER 0.36 0.57 0.7 1 MULTIPLIER 3.5 2.3 1 0.6
Flood
FloodPak® @ 45˚ Flood Photometry FPS150NLXL-1
Mounting Ht. 15’
FPM175MAL-8
Mounting Ht. 15’
FPL400MAL-8
Rotated in the 45° position, the FloodPak® transforms into an allpurpose flood for general lighting. It produces a NEMA 7 x 6 light distribution pattern for applications requiring a wide-beam pattern. In addition to above and below horizontal surface mounting, the FloodPak® can be pole mounted as a high-angle flood or ground mounted for facade and accent lighting.
Flood Lighting
Facade Lighting
Mounting Ht. 15’
WATTAGE 250 MH 250 HPS 400 HPS 400 MH
MULTIPLIER 0.57 0.79 1.39 1
MTG HT 15 20 25 30
MULTIPLIER 1.78 1 0.64 0.44
Contractor Friendly Thinking Outside the Box
Stonco developed its packaging to be user friendly for fixture selection and ease of installation.
Flexible Installation
The FloodPak® can be mounted using through-wall wiring or surface-mount ½” conduit.
Stonco is Always on the Level
An auto leveling device is part of every FloodPak® mounting box. Just rotate the box in position on the wall until level and then anchor securely.
UL Approved Splice Box
The isolated mounting box allows the contractor to use 90˚C supply wire.
Hands-Free Wiring
An integral cable holds the fixture to the installed mounting box, permitting easy hands-free wiring and single-person installation.
Specifications FloodPak® Configurations
O˚ Down
22.5˚ Down
45˚ Down
0˚ Up
22.5˚ Up
45˚ Up
Ordering Logic FPS
150
NLX
L
1
SERIES
WATTAGE
LAMP SOURCE
LAMP
VOLTAGE
L= Lamp Furnished
1=120
FPS 42 NLX=High Pressure Sodium (NPF) 70 HFL=Compact Fluorescent 100 150 HID units supplied with clear medium base lamp.
FPM
175
MA
L
8
SERIES
WATTAGE
LAMP SOURCE
LAMP
VOLTAGE
FPM 70 MA=Metal Halide (CWA) L= Lamp 100 LX=High Pressure Sodium (HX-HPF) Furnished 150 PMA=Pulse Start Metal Halide (HX-HPF) 175 HID units supplied with clear medium base lamp.
1=120 5=480 8=120/ 208 240/277
FPL
400
MA
L
8
SERIES
WATTAGE
LAMP SOURCE
LAMP
VOLTAGE
FPL 250 MA=Metal Halide (CWA) L= Lamp 400* LX=High Pressure Sodium (CWA) Furnished Supplied with clear mogul base lamp. *Requires reduced outer jacketed lamp.
Dimensional Data FPS
EPA = 0.67 sq. ft.
FPL
FPM
EPA = 0.89 sq. ft.
EPA = 1.68 sq. ft.
1=120 5=480 8=120/208/ 240/277
FloodPak® Accessories FPLARM Shoebox arm-converts FPL Series FloodPak® to pole mount (minimum 4”square pole). Use FPLRPA for mounting FPLARM to a 4” round pole.
FPSARM Shoebox arm converts FPS/FPM Series FloodPak® to pole mount (minimum 4” square). FPS and FPM onlyuse FPSRPA for mounting FPSARM to a 4” round pole.
FPLKNUCKLE Adjustable 2” Tenon Slipfitter (FPL Series only).
FPSKNUCKLE 1/2” Adjustable Knuckle (FPS and FPM Series only).
FPSSHIELD FPMSHIELD FPLSHIELD Vandal Shield - Helps protect lens and lamp from breakage. Clear polycarbonate shield snaps in place over glass lens.
FPSRPA 4” Round pole adapter for use with FPSARM. FPLRPA 4” Round pole adapter for use with FPLARM.
These mounting accessories are designed to be used with the standard FloodPak® mounting hardware (above) to adapt the luminaire to other mounting applications.
2” Pipe and Concrete Pad Applications PMAS Pipe Adapter for Small and Medium PMAL Pipe Adapter for Large
Retrofit Applications WMAS Wall-Mounting Adapter for Small and Medium
Photo Control P110A - External 120V Control P105A - Button 120v Control
2345 Vauxhall Road Union, NJ 07083 1-800-334-2212 www.FloodPak.com www.stoncolighting.com
Printed on recycled paper Minimum 10% post-consumer Printed in U.S.A. SFPBRO508-10
