iMAG 4700 - Seametrics
iMAG 4700
Mechanical Quick Start Guide Components
Power/Output Cable (DC configuration)
Cable Glands 15 Pin Connector (DC configuration)
Security Seal
Meter and Indicator
Optional
Protective faceplate cover and lanyard
Output Cable (Battery configuration)
Second Output Cable (DC configuration)
Recommended Tools Recommended:
Optional:
• T-15 Torx head driver
• Channel locks
• 0.098 inch (small) flat head screw driver • Crescent Wrench
253.872.0284 seametrics.com
iMAG 4700
Mechanical Quick Start Guide
Positioning Choose a position that will ensure a full pipe.
Choose a position that will minimize flow distortion. 5X
1X
2X
1X
5X
Recommended: Improved accuracy results from unimpeded electrodes
Not Ideal: Air bubbles and sediment on the electrodes can affect accuracy
Intermittent air bubbles miss electrode Electrode moved from top by rotating meter
1X
Intermittent air bubbles pass over electrode
Electrodes free from sediment build-up
Possible sediment build-up
Grounding Plastic Pipe
Metal Pipe Equalization Lug
Meter Flange Gasket
Grounding Ring Gaskets
Pipe Flange Equalization Lug
Grounding Ring Gaskets
Lockwasher Flange Plate
Plastic Pipe
Plastic Pipe
Ground Clamp
(Exothermically weld when corrosion is a concern)
Meter Flange Metal Pipe
Warnings
Gaskets
Pipe Flange
Earth #6, #8, or #12 AWG Stranded Copper Ground Wire < 5’
Metal Pipe
8’ Ground Rod
Refer to instruction manual for further details.
• This meter is sensitive to heat. Do not weld or flame cut within 10’ of meter. Heat will damage electronics and liner. (Heat will void warranty.) • It is highly recommended that full face gaskets be installed on each end of the meter to protect the liner. (Damage to liner will void warranty.)
• Tube must be completely aligned with adjoining flanges. • Bolts must be tightened evenly. Do not over tighten one side to fill a gap. • Improper sealing of cables or cable glands will void warranty. • Install security seal during installation if regulations require.
Refer to the Electrical Quick Start Guide or the complete instruction manual for details on wiring. Seametrics • 19026 72nd Avenue South • Kent, Washington 98032 • USA (P) 253.872.0284 • (F) 253.872.0285 • 1.800.975.8153 • seametrics.com
LT-14267r1.4 20161111 11/11/16
Mechanical Quick Start Guide Components
Power/Output Cable (DC configuration)
Cable Glands 15 Pin Connector (DC configuration)
Security Seal
Meter and Indicator
Optional
Protective faceplate cover and lanyard
Output Cable (Battery configuration)
Second Output Cable (DC configuration)
Recommended Tools Recommended:
Optional:
• T-15 Torx head driver
• Channel locks
• 0.098 inch (small) flat head screw driver • Crescent Wrench
253.872.0284 seametrics.com
iMAG 4700
Mechanical Quick Start Guide
Positioning Choose a position that will ensure a full pipe.
Choose a position that will minimize flow distortion. 5X
1X
2X
1X
5X
Recommended: Improved accuracy results from unimpeded electrodes
Not Ideal: Air bubbles and sediment on the electrodes can affect accuracy
Intermittent air bubbles miss electrode Electrode moved from top by rotating meter
1X
Intermittent air bubbles pass over electrode
Electrodes free from sediment build-up
Possible sediment build-up
Grounding Plastic Pipe
Metal Pipe Equalization Lug
Meter Flange Gasket
Grounding Ring Gaskets
Pipe Flange Equalization Lug
Grounding Ring Gaskets
Lockwasher Flange Plate
Plastic Pipe
Plastic Pipe
Ground Clamp
(Exothermically weld when corrosion is a concern)
Meter Flange Metal Pipe
Warnings
Gaskets
Pipe Flange
Earth #6, #8, or #12 AWG Stranded Copper Ground Wire < 5’
Metal Pipe
8’ Ground Rod
Refer to instruction manual for further details.
• This meter is sensitive to heat. Do not weld or flame cut within 10’ of meter. Heat will damage electronics and liner. (Heat will void warranty.) • It is highly recommended that full face gaskets be installed on each end of the meter to protect the liner. (Damage to liner will void warranty.)
• Tube must be completely aligned with adjoining flanges. • Bolts must be tightened evenly. Do not over tighten one side to fill a gap. • Improper sealing of cables or cable glands will void warranty. • Install security seal during installation if regulations require.
Refer to the Electrical Quick Start Guide or the complete instruction manual for details on wiring. Seametrics • 19026 72nd Avenue South • Kent, Washington 98032 • USA (P) 253.872.0284 • (F) 253.872.0285 • 1.800.975.8153 • seametrics.com
LT-14267r1.4 20161111 11/11/16
