iMAG 4700p - Seametrics
iMAG 4700p
Mechanical Quick Start Guide Components
Power/Output Cable
Cable Glands
Meter and Indicator
15 Pin Connector
Security Seals
Optional
Protective faceplate cover and lanyard
Six foot AC power cable for AC configurations
Second output cable
Recommended Tools Recommended:
Optional:
• T-15 Torx head driver
• Channel locks
• 0.098 inch (small) flat head screw driver • Crescent Wrench
253.872 .0 2 8 4 s eametr ics.com
iMAG 4700p
12345
Mechanical Quick Start Guide 12345
Positioning
12345
12345 12345
12345 12345 12345
Choose a position that will ensure a full pipe.
Choose a position that will minimize flow distortion. 5X
12345
1X 12345 12345
12345
12345
12345
12345
12345
12345
12345
12345
12345
12345
12345
2X
12345
1X
12345
12345
12345
12345
12345
12345
1X
12
12
34
5
34
5
5X 12 34 5
12345
12
34
5
12
34
5
12345
5
34
12
Recommended: Improved accuracy results from unimpeded electrodes
Not Ideal: Air bubbles and sediment on the electrodes can affect accuracy 5
34
12
12
34
5
Intermittent air bubbles miss electrode 5
34
12
Electrode moved from top by rotating meter
Intermittent air bubbles pass over electrode
Electrodes free from sediment build-up
12345
12345
Possible sediment build-up
Grounding
12345
Metal Pipe Equalization Lug
Meter Flange Gasket
Grounding Ring Gaskets
Pipe Flange Equalization Lug
Plastic Pipe Grounding Ring Gaskets
Lockwasher Flange Plate
Plastic Pipe
Plastic Pipe
Ground Clamp
(Exothermically weld when corrosion is a concern)
Meter Flange Metal Pipe
Warnings
Gaskets
Pipe Flange
Earth #6, #8, or #12 AWG Stranded Copper Ground Wire < 5’
Metal Pipe
8’ Ground Rod
Refer to instruction manual for further details.
• This meter is sensitive to heat. Do not weld or flame cut within 10’ of meter. Heat will damage electronics and liner. (Heat will void warranty.) • It is highly recommended that full face gaskets be installed on each end of the meter to protect the liner. (Damage to liner will void warranty.)
• Tube must be completely aligned with adjoining flanges. • Bolts must be tightened evenly. Do not over tighten one side to fill a gap. • Improper sealing of cables or cable glands will void warranty. • Install security seals during installation if regulations require.
Refer to the Electrical Quick Start Guide or the complete instruction manual for details on wiring. Seametrics • 19026 72nd Avenue South • Kent, Washington 98032 • USA (P) 253.872.0284 • (F) 253.872.0285 • 1.800.975.8153 • seametrics.com
LT-14274r1.5 20161111 11/11/16
Mechanical Quick Start Guide Components
Power/Output Cable
Cable Glands
Meter and Indicator
15 Pin Connector
Security Seals
Optional
Protective faceplate cover and lanyard
Six foot AC power cable for AC configurations
Second output cable
Recommended Tools Recommended:
Optional:
• T-15 Torx head driver
• Channel locks
• 0.098 inch (small) flat head screw driver • Crescent Wrench
253.872 .0 2 8 4 s eametr ics.com
iMAG 4700p
12345
Mechanical Quick Start Guide 12345
Positioning
12345
12345 12345
12345 12345 12345
Choose a position that will ensure a full pipe.
Choose a position that will minimize flow distortion. 5X
12345
1X 12345 12345
12345
12345
12345
12345
12345
12345
12345
12345
12345
12345
12345
2X
12345
1X
12345
12345
12345
12345
12345
12345
1X
12
12
34
5
34
5
5X 12 34 5
12345
12
34
5
12
34
5
12345
5
34
12
Recommended: Improved accuracy results from unimpeded electrodes
Not Ideal: Air bubbles and sediment on the electrodes can affect accuracy 5
34
12
12
34
5
Intermittent air bubbles miss electrode 5
34
12
Electrode moved from top by rotating meter
Intermittent air bubbles pass over electrode
Electrodes free from sediment build-up
12345
12345
Possible sediment build-up
Grounding
12345
Metal Pipe Equalization Lug
Meter Flange Gasket
Grounding Ring Gaskets
Pipe Flange Equalization Lug
Plastic Pipe Grounding Ring Gaskets
Lockwasher Flange Plate
Plastic Pipe
Plastic Pipe
Ground Clamp
(Exothermically weld when corrosion is a concern)
Meter Flange Metal Pipe
Warnings
Gaskets
Pipe Flange
Earth #6, #8, or #12 AWG Stranded Copper Ground Wire < 5’
Metal Pipe
8’ Ground Rod
Refer to instruction manual for further details.
• This meter is sensitive to heat. Do not weld or flame cut within 10’ of meter. Heat will damage electronics and liner. (Heat will void warranty.) • It is highly recommended that full face gaskets be installed on each end of the meter to protect the liner. (Damage to liner will void warranty.)
• Tube must be completely aligned with adjoining flanges. • Bolts must be tightened evenly. Do not over tighten one side to fill a gap. • Improper sealing of cables or cable glands will void warranty. • Install security seals during installation if regulations require.
Refer to the Electrical Quick Start Guide or the complete instruction manual for details on wiring. Seametrics • 19026 72nd Avenue South • Kent, Washington 98032 • USA (P) 253.872.0284 • (F) 253.872.0285 • 1.800.975.8153 • seametrics.com
LT-14274r1.5 20161111 11/11/16
