Instructions Subject: FRP ADA Splash Panel Retrofit Installation
020003338 11/10
Instructions Subject: FRP ADA Splash Panel Retrofit Installation The ADA touch pads are configured to mimic the function of the main touch pads on the left and right sides of the splash panel for handicapped accessibility to drink flavors. TOOLS NEEDED •
#2 Phillips Screwdriver
•
Power Drill
•
#29 (.136") Bit, for 6-32 Self-tapping Screw
•
Tape Measure
•
Marker or Scribe
ADA Touch Pads
KIT CONTENTS •
Splash Panel with ADA Touchpad's
•
Four Ribbon Cables
•
Zip Ties
•
ADA Flavor ID Label Sheet
•
Instruction Sheet
•
Template to Relocate Holes
ADA Ribbon Cable Wiring Diagram
INSTRUCTIONS 1. Disconnect dispenser from electrical power source. 2. Remove Merchandiser and Splash Panel. 3. Relocate both left and right Splash Panel screw mount points as shown below. Attach Template Using the Top Hole From the Bracket Removed.
Locate Current Right or Left Side Splash Panel Bracket & Remove Using #2 Phillips Screwdriver.
Use the Template to Locate , Mark, & Drill 2 New Holes Using a #29 (.136") Bit
Remove Template & Re-attach bracket.
Repeat process for opposite side of the machine.
a
b
c
d
4. Replace all 4 primary valve touch pad ribbon cables, (1,3,4,6) with the new cables supplied. Note that the new cables are numbered the same as the existing cables, (EXAMPLE: New cable marked #1 will replace existing cable #1), see the ADA Ribbon Cable Wiring Diagram illustration in the upper right of this page.
Manitowoc Beverage Systems Sellersburg, 2100 Future Drive, Sellersburg, IN 47172, Tel: 812-246-7000, www.manitowocbeverage.com
FRP ADA Splash Panel Retrofit Installation
020003338 11/10
Route Ribbon Cables
Connect New Ribbon Cables to Board
Connect Ribbon Cables to Splash Panel
NOTE: Use the zip ties provided to secure the ribbon cables. The center plug with 2 ribbon cables is plugged into the control board. The shorter of the two cables is plugged into the touch pad control above the valve. The longer ribbon cable is to be fed down behind the syrup beverage tubing, exiting out the lower front of the unit, to be connected to the ADA Touch pad in the Splash Panel, see above.
5. After connecting all four ribbon cables to their respective touch pads, place the splash panel back into position and test each pad for function, see below. Each ADA touch pads should activate the nozzle indicated below. If the wrong nozzle is activated check for a cross connection of the ribbon cable. Note that the blue LED light will illuminate, (not blink) at the touch pad control above the valve during activation. CORRESPONDING PAD
S1
S3
F1 F3
S5
S7
S12
S10
F5 F7
S16
S14
S2
S4
F2 F4
S6
S8
S11
S9
F6 F8
S15
S13
N2
N1
S1
S3
S2
S4
S5
S7
S6
S8
Connect New Ribbon Cables to Board
N3
ADA 1
ADA 2
N5
N4
ADA 3
ADA 4
N6
S16
S14
S15
S13
S12
S10
S11
S9
CORRESPONDING PAD
CORRESPONDING PAD
CORRESPONDING PAD
Connect Ribbon Cables to Splash Panel
6. Once correct operation has been confirmed, place flavor I.D. labels on ADA touch pad as shown in Photo 6 by aligning the outer edges of the label with the control pad frame, and press into place. Replace the unit Merchandiser, and then the ADA Splash Panel. As you replace the splash panel do not pinch the ribbon cables.
Manitowoc Foodservice Sellersburg, 2100 Future Drive, Sellersburg, IN 47172, Tel: 812-246-7000, www.manitowocbeverage.com
Instructions Subject: FRP ADA Splash Panel Retrofit Installation The ADA touch pads are configured to mimic the function of the main touch pads on the left and right sides of the splash panel for handicapped accessibility to drink flavors. TOOLS NEEDED •
#2 Phillips Screwdriver
•
Power Drill
•
#29 (.136") Bit, for 6-32 Self-tapping Screw
•
Tape Measure
•
Marker or Scribe
ADA Touch Pads
KIT CONTENTS •
Splash Panel with ADA Touchpad's
•
Four Ribbon Cables
•
Zip Ties
•
ADA Flavor ID Label Sheet
•
Instruction Sheet
•
Template to Relocate Holes
ADA Ribbon Cable Wiring Diagram
INSTRUCTIONS 1. Disconnect dispenser from electrical power source. 2. Remove Merchandiser and Splash Panel. 3. Relocate both left and right Splash Panel screw mount points as shown below. Attach Template Using the Top Hole From the Bracket Removed.
Locate Current Right or Left Side Splash Panel Bracket & Remove Using #2 Phillips Screwdriver.
Use the Template to Locate , Mark, & Drill 2 New Holes Using a #29 (.136") Bit
Remove Template & Re-attach bracket.
Repeat process for opposite side of the machine.
a
b
c
d
4. Replace all 4 primary valve touch pad ribbon cables, (1,3,4,6) with the new cables supplied. Note that the new cables are numbered the same as the existing cables, (EXAMPLE: New cable marked #1 will replace existing cable #1), see the ADA Ribbon Cable Wiring Diagram illustration in the upper right of this page.
Manitowoc Beverage Systems Sellersburg, 2100 Future Drive, Sellersburg, IN 47172, Tel: 812-246-7000, www.manitowocbeverage.com
FRP ADA Splash Panel Retrofit Installation
020003338 11/10
Route Ribbon Cables
Connect New Ribbon Cables to Board
Connect Ribbon Cables to Splash Panel
NOTE: Use the zip ties provided to secure the ribbon cables. The center plug with 2 ribbon cables is plugged into the control board. The shorter of the two cables is plugged into the touch pad control above the valve. The longer ribbon cable is to be fed down behind the syrup beverage tubing, exiting out the lower front of the unit, to be connected to the ADA Touch pad in the Splash Panel, see above.
5. After connecting all four ribbon cables to their respective touch pads, place the splash panel back into position and test each pad for function, see below. Each ADA touch pads should activate the nozzle indicated below. If the wrong nozzle is activated check for a cross connection of the ribbon cable. Note that the blue LED light will illuminate, (not blink) at the touch pad control above the valve during activation. CORRESPONDING PAD
S1
S3
F1 F3
S5
S7
S12
S10
F5 F7
S16
S14
S2
S4
F2 F4
S6
S8
S11
S9
F6 F8
S15
S13
N2
N1
S1
S3
S2
S4
S5
S7
S6
S8
Connect New Ribbon Cables to Board
N3
ADA 1
ADA 2
N5
N4
ADA 3
ADA 4
N6
S16
S14
S15
S13
S12
S10
S11
S9
CORRESPONDING PAD
CORRESPONDING PAD
CORRESPONDING PAD
Connect Ribbon Cables to Splash Panel
6. Once correct operation has been confirmed, place flavor I.D. labels on ADA touch pad as shown in Photo 6 by aligning the outer edges of the label with the control pad frame, and press into place. Replace the unit Merchandiser, and then the ADA Splash Panel. As you replace the splash panel do not pinch the ribbon cables.
Manitowoc Foodservice Sellersburg, 2100 Future Drive, Sellersburg, IN 47172, Tel: 812-246-7000, www.manitowocbeverage.com
