monogram 36" built-in french-door bottom-freezer zip360nh - Products
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER
ZIP360NH
SECTION 1
FLUSH INSET INSTALLATION
SECTION 2
STANDARD INSTALLATION 1/4" FRAMED PANELS
3/4" OVERLAY PANELS
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER OVERALL DIMENSIONS AFTER PANEL INSTALL
ZIP360NH
FLUSH INSET INSTALLATION 25 7/8" (65.7) 20 5/8" (52.4)
38" (96.5)
10 13/16" (27.5)
7/16" (1.1)
*84 1/2" (214.6)
*83 1/2" (212.1)
*73 5/16" (186.2)
7/16" (1.1)
*26 3/8" (70.0)
SPECIFICATIONS Overall Width
38" (96.5 cm)
Overall Height
84 1/2" (214.6 cm)
Overall Depth
25 7/8" (49.5 cm)
Door Clearance
19 1/2" (49.5 cm)
Cutout Width
39" (99.1 cm)
Cutout Height
85" (215.9 cm)
Cutout Depth
26 3/16" (66.5 cm)
Plumbing Requirements
1/4" OD copper tubing or GE SmartConnect kit
Shipping Weight
663 lb (300.7 kg)
*4"
FRONT VIEW
SIDE VIEW
(10.2)
* Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height.
35" (89.0) Case width
**8"
**8"
(20.3)
(20.3)
19 1/2" (49.5)
*115° Door swing †Doors can be adjusted to
ATTENTION ELECTRICIAN: A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.
90° door swing
4" (10.2) min distance to adjacent wall from cutout
†Allow
TOP VIEW
4" (10.2) min distance to adjacent wall from cutout
†Allow
** These refrigerators are equipped with a 2-position door stop. The factory-set 115° door swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted.
Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimensions may vary due to manufacturing tolerances.
ZIP360NH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER FLUSH INSET INSTALLATION 3/4" PANELS
FLUSH INSET INSTALLATION
TOP VIEW Case
5 1/4" (13.3)
Finished cleats Case Trim
NOTES
Door
1/2" (1.3)
3/4" Panel
26 3/16" (66.5) Flush inset depth
20 15/16" (53.2)
3/4" (1.9) Width of side cleats
Depth to cleat
39" (99.1) Flush inset width 37 1/2" (95.3) Width between cleats
4 1/16"
A
6"
ELEC.
WARNING:
(25.4)
Finished cleats
75 1/2"
(191.8 ) From floor to bottom of electrical area
85"
(215.9)
(215.9)
7"
(17.8)
3 1/2"
SIDE VIEW
W
(8.9)
B
(17.8)
3 1/2" (8.9)
FRONT VIEW
CL
Bracket mounted into vertical wall studs centered within the cutout Ensure holes selected are centered on the studs
Use two additional hole locations at end of brackets
81 1/2"
FLUSH INSTALLATION ZIP360NH
(207.0)
The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. The information below applies to all installation constructions:
7"
WATER
ANTI-TIP BRACKET
A M ounting the junction box in this location will also allow for front accessibility through access panel. B Water supply area
(15.2)
10"
(11.0)
85"
ZIP360NH
Wall Studs
•A wall bracket, bolts and toggles will be supplied with the unit. •T he bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. •T he toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. • In installation opening, measure 81-1/2" from floor and draw a horizontal line. •L ocate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated. •T he bracket will be centered left to right in opening with bottom of bracket on the horizontal line. •W hen unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts. See Installation Instructions for detailed instructions.
SIDE VIEW INSTALLED WITH ANTI-TIP BRACKET
FRONT VIEW OF CUTOUT WITH ANTI-TIP BRACKET
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER FLUSH INSET 3/4" PANEL DIMENSIONS A
FLUSH INSET INSTALLATION
PANEL DIMENSIONS B
Grille Panel E
E
Fresh Food Panel
Fresh Food Panel
A
B
38"
C
D
NOTES
E
10 13/16" 46 7/16" 22 3/8" 18 3/4"
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims.
C
D
Freezer Drawer Panel
Maximum total panel weight: • Fresh food door panels – 30 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs
3/4" RAISED FRESH FOOD DOOR PANELS ROUTING DETAIL TOP
Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3” wide and stiles must be a minimum of 4” wide.
TOP
NOTE: Routed areas should be finished as they may be visible when assembled.
3/4" 11/32" 1/4" 1/4"
ZIP360NH
7/16"
Door Handles Door handles not included. Custom handles supplied by your cabinet maker may be used.
Front
ZKHFD2H: European tubular stainless steel handles designed to fit 3/4" panels. Kit includes three handles. Back
WARNING: Back
Front
1/4"
CORNER VIEW SHOWING “PICTURE FRAME” ROUTING
DETAIL BOTTOM HINGE SIDE
HANDLE SIDE ROUTER DEPTH 1/4"
Door Trim Pinch Point Hazard Improper installation can lead to a finger pinch point hazard between the side door trim and the cabinets when operating the door, especially with children. To minimize this risk you must follow the installation instructions for cabinet dimensions, trim assembly and door stop angle.
ROUTER DEPTH 1/4"
2 1/16"
3/16"
Front LEFT SIDE
RIGHT SIDE Back
3/4" PANEL BOTTOM VIEW (AFTER ROUTING)
BOTTOM
3/4" PANEL SIDE VIEW (AFTER ROUTING)
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER 3/4" RAISED FREEZER DRAWER PANEL ROUTING
FLUSH INSET INSTALLATION
TOP
DETAIL TOP NOTE: Routed areas should be finished as they may be visible when assembled.
3/4" 11/32" 1/4" 1/4"
1/2"
NOTES
Front
Back Back
Front
1/4"
CORNER VIEW SHOWING “PICTURE FRAME” ROUTING
DETAIL BOTTOM DETAIL LEFT SIDE
DETAIL RIGHT SIDE
ROUTER DEPTH 1/4"
2 1/16"
Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3” wide and stiles must be a minimum of 4” wide.
Front LEFT SIDE
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims. Maximum total panel weight: • Fresh food door panels – 30 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs
ROUTER DEPTH 1/4"
2 1/16"
ZIP360NH
RIGHT SIDE
BOTTOM
Back
3/4" PANEL SIDE VIEW (AFTER ROUTING)
3/4" PANEL BOTTOM VIEW (AFTER ROUTING)
ZKHFD2H: European tubular stainless steel handles designed to fit 3/4" panels. Kit includes three handles.
3/4" RAISED GRILLE PANEL ROUTING TOP
DETAIL TOP
Door Handles Door handles not included. Custom handles supplied by your cabinet maker may be used.
NOTE: Routed areas should be finished as they may be visible when assembled. Front
ROUTER DEPTH 1/4"
1 11/16"
Back
Front
Back
CORNER VIEW SHOWING “PICTURE FRAME” ROUTING
BOTTOM
1/4"
DETAIL BOTTOM
DETAIL LEFT SIDE
3/4" PANEL SIDE VIEW (AFTER ROUTING)
DETAIL RIGHT SIDE
ROUTER DEPTH 1/4"
ROUTER DEPTH 1/4"
2 1/16"
2 1/16" Front LEFT SIDE
RIGHT SIDE Back
3/4" PANEL BOTTOM VIEW (AFTER ROUTING)
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER FLUSH INSET INSTALLATION 1/2" PANELS
FLUSH INSET INSTALLATION
TOP VIEW Case Finished cleats
5 3/8" (13.7)
Case Trim
NOTES
Door
1/2" (1.3)
1/2" Panel
26 3/16" (66.5) Flush inset depth
20 13/16" (52.9)
39" (99.1) Flush inset width 37 1/2" (95.3)
3/4" (1.9)
Depth to cleat
Width of side cleats
Width between cleats
4 1/16"
A
6"
ELEC.
WARNING:
(25.4)
Finished cleats
75 1/2"
(191.8 ) From floor to bottom of electrical area
85"
(215.9)
(215.9)
7"
(17.8)
3 1/2"
SIDE VIEW
W
(8.9)
7"
(17.8)
B
3 1/2" (8.9)
FRONT VIEW
CL
Bracket mounted into vertical wall studs centered within the cutout Ensure holes selected are centered on the studs
Use two additional hole locations at end of brackets
81 1/2"
Wall Studs
(207.0)
The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. The information below applies to all installation constructions:
WATER
ANTI-TIP BRACKET
A M ounting the junction box in this location will also allow for front accessibility through access panel. B Water supply area
(15.2)
10"
(11.0)
85"
ZIP360NH
FLUSH INSTALLATION ZIP360NH
•A wall bracket, bolts and toggles will be supplied with the unit. •T he bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. •T he toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. • In installation opening, measure 81-1/2" from floor and draw a horizontal line. •L ocate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated. •T he bracket will be centered left to right in opening with bottom of bracket on the horizontal line. •W hen unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts. See Installation Instructions for detailed instructions.
SIDE VIEW INSTALLED WITH ANTI-TIP BRACKET
FRONT VIEW OF CUTOUT WITH ANTI-TIP BRACKET
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER FLUSH INSET 1/2" PANEL DIMENSIONS A
FLUSH INSET INSTALLATION
PANEL DIMENSIONS B
Grille Panel E
A
E
Fresh Food Panel
Fresh Food Panel
Freezer Drawer Panel
B
C
D
E
46 1/16
21 7/8"
16 1/2"
1/4" Backer Panel
33 7/8"
8 7/8"
.10" Space Panel
32 1/2"
7 5/8" 44 11/16" 20 1/2"
1/2" Overlay Panel
38"
ZIP360NH
15"
10 13/16" 46 7/16" 22 3/8" 18 3/4"
C
NOTES The 1/2" overlay panel must be secured to a .10" spacer panel and a 1/4" thick backer panel, which slides into the trim. Assemble the panels with glue and screws: • Center the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue. •R efer to the chart for locating the backer panel to the overlay panel. Secure the overlay panel to the backer panel with glue and screws. Screws must be countersunk into the backer panel.
D
Maximum total panel weight: • Fresh food door panel – 30 lbs.
1/4" BACKER ASSEMBLY DIMENSIONS
• Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs.
Hinge Side
C
C
Door
1/2" Overlay Panel
Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of 4" wide.
WARNING: Backer with Overlay Panel Assembly Fresh Food Back
Fresh Food Back
B
A
D
A
D
1/4" Backer Panel
B
C
C A
.10" Spacer
Door Trim Pinch Point Hazard Improper installation can lead to a finger pinch point hazard between the side door trim and the cabinets when operating the door, especially with children. To minimize this risk you must follow the installation instructions for cabinet dimensions, trim assembly and door stop angle.
Freezer Drawer
Grille Back
D
B
A
D
B
PANEL DIMENSIONS A
B
C
D
Fresh Food Door Panels
2 1/16"
3/16"
3/16"
3/16"
Freezer Drawer Panel
2 1/16"
2 1/16"
1/4"
1/4"
Grille Panel
2 1/16"
2 1/16"
1 11/16"
1/4"
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER OVERALL DIMENSIONS AFTER PANEL INSTALL
ZIP360NH
STANDARD INSTALLATION 25 3/8" (64.5) 23 13/16" (60.5)
36" (91.4) 9 7/8"
1 5/8" (4.1)
(25.1)
9/16" (1.4)
46 5/16"
*84"
(117.7)
(213.4)
*83 1/2" (212.1)
*73 1/4" (186.1)
1/2" (1.3)
*26 7/16"
SPECIFICATIONS
(67.1)
Overall Width
36" (91.4 cm)
Overall Height
84" (213.4 cm)
Overall Depth
25 3/8" (64.5 cm)
Door Clearance
18 3/16" (46.2 cm)
Cutout Width
35 1/2" (90.2 cm)
Cutout Height
84" (213.4 cm)
Cutout Depth
24" (61 cm)
Plumbing Requirements
1/4" OD copper tubing or GE SmartConnect kit
Shipping Weight
614 lb
*4 1/8"
FRONT VIEW
(10.5)
SIDE VIEW
*Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height.
35" (89.0) Case width
**12 7/8"
**12 7/8"
(32.7)
(32.7)
ATTENTION ELECTRICIAN: A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.
18 3/16" (46.2)
**130° Door swing †Doors can be adjusted to
90° door swing
4" (10.2) min distance to adjacent wall from cutout
†Allow
4" (10.2) min distance to adjacent wall from cutout
†Allow
TOP VIEW (SHOWING DOOR SWING)
Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimensions may vary ZIP360NZ due to manufacturing tolerances. Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER STANDARD INSTALLATION 3/4" PANELS
STANDARD INSTALLATION TOP VIEW
3 1/8" (7.93)
24" (61)
7/16" (1.1) Trim overlap
1 9/16" (3.97)
NOTES A M ounting the junction box in this location will also allow for front accessibility through access panel. B Water supply area
35 1/2" (90.2)
2 5/16"
A
(5.874)
ELEC.
6"
(15.24)
WARNING:
10"
(25.4)
75"
*84"
(190.5 ) From floor to bottom of electrical area
(213.4) *Trim will overlap additional 7/16"
5"
(12.7)
3 1/2"
W
(8.9)
B
5"
3 1/2"
(12.7)
(8.9)
WATER
ANTI-TIP BRACKET
CL
Bracket mounted into vertical wall studs centered within the cutout
Use two additional hole locations at end of brackets
81 1/2" (207.0)
The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. The information below applies to all installation constructions: •A wall bracket, bolts and toggles will be supplied with the unit.
FRONT VIEW
SIDE VIEW
ZIP360NH
Ensure holes selected are centered on the studs
Wall Studs
STANDARD_INSTALLATION ZIP360NH
•T he bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. •T he toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. • In installation opening, measure 81-1/2" from floor and draw a horizontal line. •L ocate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated. •T he bracket will be centered left to right in opening with bottom of bracket on the horizontal line. •W hen unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts.
SIDE VIEW INSTALLED WITH ANTI-TIP BRACKET
FRONT VIEW OF CUTOUT WITH ANTI-TIP BRACKET
See Installation Instructions for detailed instructions.
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER STANDARD 1/4" FRAMED PANEL DIMENSIONS
B
Grille Panel E
Trim
NOTES
Door
Trimmed refrigerators are designed to be customized with decorative panels Field-installed custom door and grille panels are required.
E 1/4" Framed Panel
Fresh Food Panel
STANDARD INSTALLATION
PANEL ASSEMBLY CROSS SECTION
A
Fresh Food Panel
Freezer Drawer Panel
ZIP360NH
Supplied Handles
1/4" Framed Panels:
C
D
For 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into this trim. Maximum total panel weight: • Fresh food door panel – 30 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs
PANEL DIMENSIONS A
B
C
D
E
1/4" Framed Panel 33 7/8" 8 7/8" 46 1/16" 21 7/8" 16 1/2"
Door Handles: The supplied handles accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker, can also be installed. .
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER STANDARD 3/4" OVERLAY PANEL DIMENSIONS A
STANDARD INSTALLATION
PANEL ASSEMBLY CROSS SECTION B
Grille Panel E
Trim
E
.10" Spacer Panel
NOTES
Door
1/4" Backer Panel
Trimmed refrigerators are designed to be customized with decorative panels Field-installed custom door and grille panels are required.
3/4" Overlay Panel Supplied Handles
Fresh Food Panel
Fresh Food Panel
C 3/4" Overlay Panels:
PANEL DIMENSIONS A
Freezer Drawer Panel
D
B
C
D
E
1/4" Framed Panel
33 7/8" 8 7/8" 46 1/16" 21 7/8" 16 1/2"
.10" Framed Panel
32 1/2" 7 5/8" 44 11/16" 20 1/2"
3/4" Overlay Panel 34 1/8"
9"
46 5/16"
22"
15" 16 5/8"
.25" + .10" + .75" = 1.10" Total Panel Thickness
Hinge Side
NOTE: Left-to-right offset is not always equal to top-to-bottom offset.
C
C
Door
Maximum total panel weight: • Fresh food door panel – 30 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs
1/2" Overlay Panel
Door Handles: The supplied handles accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker, can also be installed.
Backer with Overlay Panel Assembly Fresh Food Back
Fresh Food Back
B
A
A
D
1/4" Backer Panel
A
ZKHFD2H: European tubular stainless steel handles designed to fit 3/4" panels. Kit includes three handles.
.10" Spacer
B
C
C
For your 3/4" thick custom panels ordered from your cabinet maker the overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels. Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.
1/4" BACKER ASSEMBLY DIMENSIONS
D
ZIP360NH
Freezer Drawer
Grille Back
D
B
A
D
B
PANEL DIMENSIONS A
B
C
D
Fresh Food Door Panels
1/8"
0
1/8"
1/8"
Freezer Drawer Panel
1/8"
1/8"
1/16"
1/16"
Grille Panel
1/8"
1/8"
1/16"
1/16"
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER
ZIP360NH
FEATURES AND BENEFITS FRENCH DOOR DESIGN Gives your wide-open access to every fresh food shelf and bin FINELY CRAFTED GLASS-FRONT METAL DOOR BINS WITH RIVETED METAL ACCENTS offer easy access to beverages and quick-grab items LED LIGHTING positioned throughout the interior and under fresh food drawers spotlights food inside the refrigerator and in the freezer UPFRONT ELECTRONIC CONTROLS WITH DIGITAL READOUT Offer a range of precise temperature settings, all within easy reach LARGE FULL-EXTENSION FREEZER DRAWER has storage bins that slide out independently of one another for easy loading and unloading. An automatic icemaker keeps plenty of filtered ice on hand PRECISION GLASS-FRONT PRODUCE AND DELI DRAWERS Feature full-extension, soft-close slides ALUMINUM TRIMMED GLASS SHELVES Allow convenient access to contents in the fresh-food compartment
Product Specification Revised 1/18
ZIP360NH
SECTION 1
FLUSH INSET INSTALLATION
SECTION 2
STANDARD INSTALLATION 1/4" FRAMED PANELS
3/4" OVERLAY PANELS
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER OVERALL DIMENSIONS AFTER PANEL INSTALL
ZIP360NH
FLUSH INSET INSTALLATION 25 7/8" (65.7) 20 5/8" (52.4)
38" (96.5)
10 13/16" (27.5)
7/16" (1.1)
*84 1/2" (214.6)
*83 1/2" (212.1)
*73 5/16" (186.2)
7/16" (1.1)
*26 3/8" (70.0)
SPECIFICATIONS Overall Width
38" (96.5 cm)
Overall Height
84 1/2" (214.6 cm)
Overall Depth
25 7/8" (49.5 cm)
Door Clearance
19 1/2" (49.5 cm)
Cutout Width
39" (99.1 cm)
Cutout Height
85" (215.9 cm)
Cutout Depth
26 3/16" (66.5 cm)
Plumbing Requirements
1/4" OD copper tubing or GE SmartConnect kit
Shipping Weight
663 lb (300.7 kg)
*4"
FRONT VIEW
SIDE VIEW
(10.2)
* Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height.
35" (89.0) Case width
**8"
**8"
(20.3)
(20.3)
19 1/2" (49.5)
*115° Door swing †Doors can be adjusted to
ATTENTION ELECTRICIAN: A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.
90° door swing
4" (10.2) min distance to adjacent wall from cutout
†Allow
TOP VIEW
4" (10.2) min distance to adjacent wall from cutout
†Allow
** These refrigerators are equipped with a 2-position door stop. The factory-set 115° door swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted.
Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimensions may vary due to manufacturing tolerances.
ZIP360NH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER FLUSH INSET INSTALLATION 3/4" PANELS
FLUSH INSET INSTALLATION
TOP VIEW Case
5 1/4" (13.3)
Finished cleats Case Trim
NOTES
Door
1/2" (1.3)
3/4" Panel
26 3/16" (66.5) Flush inset depth
20 15/16" (53.2)
3/4" (1.9) Width of side cleats
Depth to cleat
39" (99.1) Flush inset width 37 1/2" (95.3) Width between cleats
4 1/16"
A
6"
ELEC.
WARNING:
(25.4)
Finished cleats
75 1/2"
(191.8 ) From floor to bottom of electrical area
85"
(215.9)
(215.9)
7"
(17.8)
3 1/2"
SIDE VIEW
W
(8.9)
B
(17.8)
3 1/2" (8.9)
FRONT VIEW
CL
Bracket mounted into vertical wall studs centered within the cutout Ensure holes selected are centered on the studs
Use two additional hole locations at end of brackets
81 1/2"
FLUSH INSTALLATION ZIP360NH
(207.0)
The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. The information below applies to all installation constructions:
7"
WATER
ANTI-TIP BRACKET
A M ounting the junction box in this location will also allow for front accessibility through access panel. B Water supply area
(15.2)
10"
(11.0)
85"
ZIP360NH
Wall Studs
•A wall bracket, bolts and toggles will be supplied with the unit. •T he bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. •T he toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. • In installation opening, measure 81-1/2" from floor and draw a horizontal line. •L ocate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated. •T he bracket will be centered left to right in opening with bottom of bracket on the horizontal line. •W hen unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts. See Installation Instructions for detailed instructions.
SIDE VIEW INSTALLED WITH ANTI-TIP BRACKET
FRONT VIEW OF CUTOUT WITH ANTI-TIP BRACKET
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER FLUSH INSET 3/4" PANEL DIMENSIONS A
FLUSH INSET INSTALLATION
PANEL DIMENSIONS B
Grille Panel E
E
Fresh Food Panel
Fresh Food Panel
A
B
38"
C
D
NOTES
E
10 13/16" 46 7/16" 22 3/8" 18 3/4"
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims.
C
D
Freezer Drawer Panel
Maximum total panel weight: • Fresh food door panels – 30 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs
3/4" RAISED FRESH FOOD DOOR PANELS ROUTING DETAIL TOP
Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3” wide and stiles must be a minimum of 4” wide.
TOP
NOTE: Routed areas should be finished as they may be visible when assembled.
3/4" 11/32" 1/4" 1/4"
ZIP360NH
7/16"
Door Handles Door handles not included. Custom handles supplied by your cabinet maker may be used.
Front
ZKHFD2H: European tubular stainless steel handles designed to fit 3/4" panels. Kit includes three handles. Back
WARNING: Back
Front
1/4"
CORNER VIEW SHOWING “PICTURE FRAME” ROUTING
DETAIL BOTTOM HINGE SIDE
HANDLE SIDE ROUTER DEPTH 1/4"
Door Trim Pinch Point Hazard Improper installation can lead to a finger pinch point hazard between the side door trim and the cabinets when operating the door, especially with children. To minimize this risk you must follow the installation instructions for cabinet dimensions, trim assembly and door stop angle.
ROUTER DEPTH 1/4"
2 1/16"
3/16"
Front LEFT SIDE
RIGHT SIDE Back
3/4" PANEL BOTTOM VIEW (AFTER ROUTING)
BOTTOM
3/4" PANEL SIDE VIEW (AFTER ROUTING)
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER 3/4" RAISED FREEZER DRAWER PANEL ROUTING
FLUSH INSET INSTALLATION
TOP
DETAIL TOP NOTE: Routed areas should be finished as they may be visible when assembled.
3/4" 11/32" 1/4" 1/4"
1/2"
NOTES
Front
Back Back
Front
1/4"
CORNER VIEW SHOWING “PICTURE FRAME” ROUTING
DETAIL BOTTOM DETAIL LEFT SIDE
DETAIL RIGHT SIDE
ROUTER DEPTH 1/4"
2 1/16"
Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3” wide and stiles must be a minimum of 4” wide.
Front LEFT SIDE
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims. Maximum total panel weight: • Fresh food door panels – 30 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs
ROUTER DEPTH 1/4"
2 1/16"
ZIP360NH
RIGHT SIDE
BOTTOM
Back
3/4" PANEL SIDE VIEW (AFTER ROUTING)
3/4" PANEL BOTTOM VIEW (AFTER ROUTING)
ZKHFD2H: European tubular stainless steel handles designed to fit 3/4" panels. Kit includes three handles.
3/4" RAISED GRILLE PANEL ROUTING TOP
DETAIL TOP
Door Handles Door handles not included. Custom handles supplied by your cabinet maker may be used.
NOTE: Routed areas should be finished as they may be visible when assembled. Front
ROUTER DEPTH 1/4"
1 11/16"
Back
Front
Back
CORNER VIEW SHOWING “PICTURE FRAME” ROUTING
BOTTOM
1/4"
DETAIL BOTTOM
DETAIL LEFT SIDE
3/4" PANEL SIDE VIEW (AFTER ROUTING)
DETAIL RIGHT SIDE
ROUTER DEPTH 1/4"
ROUTER DEPTH 1/4"
2 1/16"
2 1/16" Front LEFT SIDE
RIGHT SIDE Back
3/4" PANEL BOTTOM VIEW (AFTER ROUTING)
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER FLUSH INSET INSTALLATION 1/2" PANELS
FLUSH INSET INSTALLATION
TOP VIEW Case Finished cleats
5 3/8" (13.7)
Case Trim
NOTES
Door
1/2" (1.3)
1/2" Panel
26 3/16" (66.5) Flush inset depth
20 13/16" (52.9)
39" (99.1) Flush inset width 37 1/2" (95.3)
3/4" (1.9)
Depth to cleat
Width of side cleats
Width between cleats
4 1/16"
A
6"
ELEC.
WARNING:
(25.4)
Finished cleats
75 1/2"
(191.8 ) From floor to bottom of electrical area
85"
(215.9)
(215.9)
7"
(17.8)
3 1/2"
SIDE VIEW
W
(8.9)
7"
(17.8)
B
3 1/2" (8.9)
FRONT VIEW
CL
Bracket mounted into vertical wall studs centered within the cutout Ensure holes selected are centered on the studs
Use two additional hole locations at end of brackets
81 1/2"
Wall Studs
(207.0)
The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. The information below applies to all installation constructions:
WATER
ANTI-TIP BRACKET
A M ounting the junction box in this location will also allow for front accessibility through access panel. B Water supply area
(15.2)
10"
(11.0)
85"
ZIP360NH
FLUSH INSTALLATION ZIP360NH
•A wall bracket, bolts and toggles will be supplied with the unit. •T he bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. •T he toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. • In installation opening, measure 81-1/2" from floor and draw a horizontal line. •L ocate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated. •T he bracket will be centered left to right in opening with bottom of bracket on the horizontal line. •W hen unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts. See Installation Instructions for detailed instructions.
SIDE VIEW INSTALLED WITH ANTI-TIP BRACKET
FRONT VIEW OF CUTOUT WITH ANTI-TIP BRACKET
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER FLUSH INSET 1/2" PANEL DIMENSIONS A
FLUSH INSET INSTALLATION
PANEL DIMENSIONS B
Grille Panel E
A
E
Fresh Food Panel
Fresh Food Panel
Freezer Drawer Panel
B
C
D
E
46 1/16
21 7/8"
16 1/2"
1/4" Backer Panel
33 7/8"
8 7/8"
.10" Space Panel
32 1/2"
7 5/8" 44 11/16" 20 1/2"
1/2" Overlay Panel
38"
ZIP360NH
15"
10 13/16" 46 7/16" 22 3/8" 18 3/4"
C
NOTES The 1/2" overlay panel must be secured to a .10" spacer panel and a 1/4" thick backer panel, which slides into the trim. Assemble the panels with glue and screws: • Center the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue. •R efer to the chart for locating the backer panel to the overlay panel. Secure the overlay panel to the backer panel with glue and screws. Screws must be countersunk into the backer panel.
D
Maximum total panel weight: • Fresh food door panel – 30 lbs.
1/4" BACKER ASSEMBLY DIMENSIONS
• Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs.
Hinge Side
C
C
Door
1/2" Overlay Panel
Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of 4" wide.
WARNING: Backer with Overlay Panel Assembly Fresh Food Back
Fresh Food Back
B
A
D
A
D
1/4" Backer Panel
B
C
C A
.10" Spacer
Door Trim Pinch Point Hazard Improper installation can lead to a finger pinch point hazard between the side door trim and the cabinets when operating the door, especially with children. To minimize this risk you must follow the installation instructions for cabinet dimensions, trim assembly and door stop angle.
Freezer Drawer
Grille Back
D
B
A
D
B
PANEL DIMENSIONS A
B
C
D
Fresh Food Door Panels
2 1/16"
3/16"
3/16"
3/16"
Freezer Drawer Panel
2 1/16"
2 1/16"
1/4"
1/4"
Grille Panel
2 1/16"
2 1/16"
1 11/16"
1/4"
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER OVERALL DIMENSIONS AFTER PANEL INSTALL
ZIP360NH
STANDARD INSTALLATION 25 3/8" (64.5) 23 13/16" (60.5)
36" (91.4) 9 7/8"
1 5/8" (4.1)
(25.1)
9/16" (1.4)
46 5/16"
*84"
(117.7)
(213.4)
*83 1/2" (212.1)
*73 1/4" (186.1)
1/2" (1.3)
*26 7/16"
SPECIFICATIONS
(67.1)
Overall Width
36" (91.4 cm)
Overall Height
84" (213.4 cm)
Overall Depth
25 3/8" (64.5 cm)
Door Clearance
18 3/16" (46.2 cm)
Cutout Width
35 1/2" (90.2 cm)
Cutout Height
84" (213.4 cm)
Cutout Depth
24" (61 cm)
Plumbing Requirements
1/4" OD copper tubing or GE SmartConnect kit
Shipping Weight
614 lb
*4 1/8"
FRONT VIEW
(10.5)
SIDE VIEW
*Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height.
35" (89.0) Case width
**12 7/8"
**12 7/8"
(32.7)
(32.7)
ATTENTION ELECTRICIAN: A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.
18 3/16" (46.2)
**130° Door swing †Doors can be adjusted to
90° door swing
4" (10.2) min distance to adjacent wall from cutout
†Allow
4" (10.2) min distance to adjacent wall from cutout
†Allow
TOP VIEW (SHOWING DOOR SWING)
Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimensions may vary ZIP360NZ due to manufacturing tolerances. Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER STANDARD INSTALLATION 3/4" PANELS
STANDARD INSTALLATION TOP VIEW
3 1/8" (7.93)
24" (61)
7/16" (1.1) Trim overlap
1 9/16" (3.97)
NOTES A M ounting the junction box in this location will also allow for front accessibility through access panel. B Water supply area
35 1/2" (90.2)
2 5/16"
A
(5.874)
ELEC.
6"
(15.24)
WARNING:
10"
(25.4)
75"
*84"
(190.5 ) From floor to bottom of electrical area
(213.4) *Trim will overlap additional 7/16"
5"
(12.7)
3 1/2"
W
(8.9)
B
5"
3 1/2"
(12.7)
(8.9)
WATER
ANTI-TIP BRACKET
CL
Bracket mounted into vertical wall studs centered within the cutout
Use two additional hole locations at end of brackets
81 1/2" (207.0)
The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. The information below applies to all installation constructions: •A wall bracket, bolts and toggles will be supplied with the unit.
FRONT VIEW
SIDE VIEW
ZIP360NH
Ensure holes selected are centered on the studs
Wall Studs
STANDARD_INSTALLATION ZIP360NH
•T he bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. •T he toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. • In installation opening, measure 81-1/2" from floor and draw a horizontal line. •L ocate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated. •T he bracket will be centered left to right in opening with bottom of bracket on the horizontal line. •W hen unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts.
SIDE VIEW INSTALLED WITH ANTI-TIP BRACKET
FRONT VIEW OF CUTOUT WITH ANTI-TIP BRACKET
See Installation Instructions for detailed instructions.
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER STANDARD 1/4" FRAMED PANEL DIMENSIONS
B
Grille Panel E
Trim
NOTES
Door
Trimmed refrigerators are designed to be customized with decorative panels Field-installed custom door and grille panels are required.
E 1/4" Framed Panel
Fresh Food Panel
STANDARD INSTALLATION
PANEL ASSEMBLY CROSS SECTION
A
Fresh Food Panel
Freezer Drawer Panel
ZIP360NH
Supplied Handles
1/4" Framed Panels:
C
D
For 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into this trim. Maximum total panel weight: • Fresh food door panel – 30 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs
PANEL DIMENSIONS A
B
C
D
E
1/4" Framed Panel 33 7/8" 8 7/8" 46 1/16" 21 7/8" 16 1/2"
Door Handles: The supplied handles accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker, can also be installed. .
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER STANDARD 3/4" OVERLAY PANEL DIMENSIONS A
STANDARD INSTALLATION
PANEL ASSEMBLY CROSS SECTION B
Grille Panel E
Trim
E
.10" Spacer Panel
NOTES
Door
1/4" Backer Panel
Trimmed refrigerators are designed to be customized with decorative panels Field-installed custom door and grille panels are required.
3/4" Overlay Panel Supplied Handles
Fresh Food Panel
Fresh Food Panel
C 3/4" Overlay Panels:
PANEL DIMENSIONS A
Freezer Drawer Panel
D
B
C
D
E
1/4" Framed Panel
33 7/8" 8 7/8" 46 1/16" 21 7/8" 16 1/2"
.10" Framed Panel
32 1/2" 7 5/8" 44 11/16" 20 1/2"
3/4" Overlay Panel 34 1/8"
9"
46 5/16"
22"
15" 16 5/8"
.25" + .10" + .75" = 1.10" Total Panel Thickness
Hinge Side
NOTE: Left-to-right offset is not always equal to top-to-bottom offset.
C
C
Door
Maximum total panel weight: • Fresh food door panel – 30 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs
1/2" Overlay Panel
Door Handles: The supplied handles accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker, can also be installed.
Backer with Overlay Panel Assembly Fresh Food Back
Fresh Food Back
B
A
A
D
1/4" Backer Panel
A
ZKHFD2H: European tubular stainless steel handles designed to fit 3/4" panels. Kit includes three handles.
.10" Spacer
B
C
C
For your 3/4" thick custom panels ordered from your cabinet maker the overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels. Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.
1/4" BACKER ASSEMBLY DIMENSIONS
D
ZIP360NH
Freezer Drawer
Grille Back
D
B
A
D
B
PANEL DIMENSIONS A
B
C
D
Fresh Food Door Panels
1/8"
0
1/8"
1/8"
Freezer Drawer Panel
1/8"
1/8"
1/16"
1/16"
Grille Panel
1/8"
1/8"
1/16"
1/16"
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN FRENCH-DOOR BOTTOM-FREEZER
ZIP360NH
FEATURES AND BENEFITS FRENCH DOOR DESIGN Gives your wide-open access to every fresh food shelf and bin FINELY CRAFTED GLASS-FRONT METAL DOOR BINS WITH RIVETED METAL ACCENTS offer easy access to beverages and quick-grab items LED LIGHTING positioned throughout the interior and under fresh food drawers spotlights food inside the refrigerator and in the freezer UPFRONT ELECTRONIC CONTROLS WITH DIGITAL READOUT Offer a range of precise temperature settings, all within easy reach LARGE FULL-EXTENSION FREEZER DRAWER has storage bins that slide out independently of one another for easy loading and unloading. An automatic icemaker keeps plenty of filtered ice on hand PRECISION GLASS-FRONT PRODUCE AND DELI DRAWERS Feature full-extension, soft-close slides ALUMINUM TRIMMED GLASS SHELVES Allow convenient access to contents in the fresh-food compartment
Product Specification Revised 1/18
