zic360nhlh monogram 36" built-in bottom-freezer refrigerator - Products
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR
ZIC360NHLH
SECTION 1
FLUSH INSET INSTALLATION
SECTION 2
STANDARD INSTALLATION 1/4" FRAMED PANELS
3/4" OVERLAY PANELS
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR OVERALL DIMENSIONS AFTER PANEL INSTALL
ZIC360NHLH
FLUSH INSET INSTALLATION 26" (66.0) 20 5/8" (52.4)
38" (96.5)
11 1/2" (29.2)
* 84 1/2"
* 83 1/2" (212.1)
(214.6)
*73"
(185.4)
SPECIFICATIONS
*26 7/16" (67.1)
Overall Width
38" (96.5 cm)†
Overall Height
84 1/2" (214.6 cm)†
Overall Depth
26" (66.0 cm)†
Door Clearance
38 3/4" (98.4 cm)
Cutout Width
39" (99.1 cm)
Cutout Height
85" (215.9 cm)
Cutout Depth
26 3/16" (66.5 cm)
Plumbing Requirements
1/4" OD copper tubing or GE SmartConnect kit
Shipping Weight
640 lb (290.3 kg)
FRONT VIEW
*4"
*4"
SIDE VIEW
(10.2)
(10.2)
* Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height. Nominal installation height is 84”
35" (89.0) Case width
Allow 15" (38.1) min clearance for 115˚ door swing
† Dimensions include 3/4" custom cabinet panel
TOP VIEW ATTENTION ELECTRICIAN: A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.
38 3/4" (98.4)
Allow 4" (10.2) min clearance to a wall for 90˚ door swing
Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimensions may vary due to manufacturing tolerances. Product Specification Revised 1/18 ZIC360NHLH
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR FLUSH INSET INSTALLATION 3/4" PANELS
ZIC360NHLH
FLUSH INSET INSTALLATION
TOP VIEW Case
5 1/4" (13.3)
35 1/2" (90.2)
2 5/16" (5.9)
6"
ELEC.
Flush inset depth
10" 20 15/16" (25.4) (53.2) *83 1/2" min *84 1/2" max
3/4" (1.9)
Depth to cleat
Width of side cleats
39" (99.1) Flush inset width 37 1/2" (95.3) Width between cleats
(212.1-214.6) *Trim will overlap additional 7/16"
10"
75"
(25.4)
(190.5 ) From floor to bottom of electrical area
(15.2)
(61.4)
75 1/2"
WATER 3 1/2"
5"
(12.7)
(191.8 ) From floor to bottom of electrical area
(213.4) height to cleat
(215.9)
5" 3 1/2"
(9.0)
(12.7)
7"
(17.8)
3 1/2"
FRONT VIEW (8.9)
SIDE VIEW
B WATER 3 1/2" (9.0)
WATER 7" (17.8) 3 1/2"
SIDE VIEW
W
A M ounting the junction box in this location will also allow for front accessibility through access panel. B Water supply area. WARNING:
The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. The information below applies to all installation constructions:
10"(25.4)
(8.9)
NOTES
The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury.
24 3/16"
84"
85"
A
6"
ELEC.
Finished cleats
7/16" (1.1) Trim overlap
1/2" (1.3)
3/4" Panel
(15.2)
26 3/16" (66.5)
3"Finished cleats 24" (61.0) (7.6) Case Trim 1 1/2" (3.8) Door
(8.9)
FRONT VIEW
• A wall bracket, bolts and toggles will be supplied with the unit. • The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. • The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs.
ANTI-TIP BRACKET
CL
Use two additional hole locations at end of brackets
FLUSH INSTALLATION 81 1/2" ZIC360NHLH_RH (207.0)
Bracket mounted into vertical wall studs centered within the cutout Ensure holes selected are centered on the studs
Wall Studs
• In installation opening, measure 82" from floor and draw a horizontal line. • Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated. • The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. • When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts. See Installation Instructions for detailed instructions.
SIDE VIEW INSTALLED WITH ANTI-TIP BRACKET
FRONT VIEW OF CUTOUT WITH ANTI-TIP BRACKET
ZIC360NXRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR FLUSH INSET 3/4" PANEL DIMENSIONS SINGLE INSTALLATION
FLUSH INSET INSTALLATION
A
PANEL DIMENSIONS
B
Grille Panel
A 38"
Fresh Food Panel
B
C
NOTES
D
10 11/16" 46 9/16" 22 7/16"
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims.
C
D
Freezer Drawer Panel
ZIC360NHLH
Maximum total panel weight: • Fresh food door panels – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of 4" wide.
3/4" RAISED DOOR PANEL ROUTING TOP
DETAIL TOP NOTE: Routed areas should be finished as they may be visible when assembled.
3/4" 11/32" 1/4" 1/4"
7/16"
Door Handles Door handles not included. Custom handles supplied by your cabinet maker may be used.
Front
ZKHPSS1: Professional tubular stainless steel handle designed to fit custom panels. Kit includes one handle – 30-1/2" long. Order 2 kits from your Monogram supplier.
Back Back
Front
Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs.
1/4"
CORNER VIEW SHOWING “PICTURE FRAME” ROUTING
DETAIL BOTTOM
DETAIL LEFT SIDE
ZKHCSS2: Custom European tubular handle designed to fit custom panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16".
ZKHCT: Handle side trim for left-hand and right-hand door. For use on a custom panel when using a custom handle.
DETAIL RIGHT SIDE ROUTER DEPTH 1/4"
ROUTER DEPTH 1/4" 3/32" 1/4"
2-1/16"
2-1/16" Front
LEFT SIDE
RIGHT SIDE Back
3/4" PANEL BOTTOM VIEW (AFTER ROUTING)
BOTTOM
3/4" PANEL SIDE VIEW (AFTER ROUTING)
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR 3/4" RAISED GRILL PANEL ROUTING NOTE: Routed areas should be finished as they may be visible when assembled.
DETAIL TOP
FLUSH INSET INSTALLATION
TOP
NOTES
Front
1-11/16" ROUTER DEPTH 1/4"
Back Back
Front
CORNER VIEW SHOWING “PICTURE FRAME” ROUTING DETAIL LEFT SIDE
DETAIL RIGHT SIDE ROUTER DEPTH 1/4"
ROUTER DEPTH 1/4" 3/32"
BOTTOM
1/4"
3/16"
2-1/16"
3/4" PANEL SIDE VIEW (AFTER ROUTING)
2-1/16"
DETAIL BOTTOM
Front LEFT SIDE Back
3/4" RAISED DRAWER PANEL ROUTING
ZKHPSS1: Professional tubular stainless steel handle designed to fit custom panels. Kit includes one handle – 30-1/2" long. Order 2 kits from your Monogram supplier.
TOP
NOTE: Routed areas should be finished as they may be visible when assembled.
11/32" 1/4" 1/4"
Maximum total panel weight: • Fresh food door panels – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs
Door Handles Door handles not included. Custom handles supplied by your cabinet maker may be used.
3/4" PANEL BOTTOM VIEW (AFTER ROUTING)
3/4"
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims.
Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of 4" wide.
RIGHT SIDE
DETAIL TOP
ZIC360NHLH
ZKHCSS2: Custom European tubular handle designed to fit custom panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16".
Front
7/16"
Back Back
Front
Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs. ZKHCT: Handle side trim for left-hand and right-hand door. For use on a custom panel when using a custom handle.
1/4"
CORNER VIEW SHOWING “PICTURE FRAME” ROUTING DETAIL BOTTOM DETAIL LEFT SIDE
DETAIL RIGHT SIDE
ROUTER DEPTH 1/4"
ROUTER DEPTH 1/4"
2 1/16"
2 1/16" Front
LEFT SIDE
RIGHT SIDE
BOTTOM
Back
3/4" PANEL BOTTOM VIEW (AFTER ROUTING)
3/4" PANEL SIDE VIEW (AFTER ROUTING)
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR FLUSH INSET INSTALLATION 1/2" PANELS
FLUSH INSET INSTALLATION
TOP VIEW 35 1/2" (90.2)
2 5/16"
5 3/8" (13.7)
(5.9)
3"
Case (7.6) Finished cleats
24" (61.0) 1 1/2"
Case Trim
26 3/16" (66.5) Flush inset depth 10" (25.4) 20 13/16" (52.9) *83 1/2" min Depth to cleat *84 1/2" max
7/16" (1.1) Trim overlap
(3.8)
Door
6"
ELEC.
(15.2)
1/2" (1.3)
1/2" Panel
3/4" (1.9)
Width of side cleats
39" (99.1) Flush inset width 37 1/2" (95.3) Width between cleats
(212.1-214.6) *Trim will overlap additional 7/16"
10"
75"
(25.4)
(190.5 ) From floor to bottom of electrical area
Finished cleats
The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury.
24 3/16" (61.4)
75 1/2"
WATER 3 1/2"
5"
(12.7)
(9.0)
(191.8 ) From floor to bottom of electrical area
(213.4) height to cleat
(215.9)
5" 3 1/2"
(12.7)
(8.9)
7"
(17.8)
3 1/2" FRONT VIEW (8.9)
SIDE VIEW
B WATER 3 1/2" (9.0)
The information below applies to all installation constructions:
WATER
• A wall bracket, bolts and toggles will be supplied with the unit.
7"
(17.8)
3 1/2" (8.9)
FRONT VIEW
ANTI-TIP BRACKET
CL
Use two additional hole locations at end of brackets
FLUSH INSTALLATION ZIC360NHLH_RH 81 1/2" (207.0)
The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions.
10"(25.4)
SIDE VIEW
W
A M ounting the junction box in this location will also allow for front accessibility through access panel. B Water supply area. WARNING:
(15.2)
84"
85"
NOTES
A
6"
ELEC.
ZIC360NHLH
Bracket mounted into vertical wall studs centered within the cutout Ensure holes selected are centered on the studs
Wall Studs
• The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. • The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. • In installation opening, measure 82" from floor and draw a horizontal line. • Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated. • The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. • When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts. See Installation Instructions for detailed instructions.
SIDE VIEW INSTALLED WITH ANTI-TIP BRACKET
FRONT VIEW OF CUTOUT WITH ANTI-TIP BRACKET
ZIC360NXRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR FLUSH INSET 1/2" PANEL DIMENSIONS A
FLUSH INSET INSTALLATION
PANEL DIMENSIONS A
B
1/4" Backer Panel
33 7/8"
8 7/8"
.10" Space Panel
32 1/2"
7 5/8" 44 11/16" 20 1/2"
38"
10 11/16" 46 9/16" 22 7/16"
B
Grille Panel
1/2" Overlay Panel
Fresh Food Panel
C
D
NOTES
46 1/16" 21 7/8"
The 1/2" overlay panel must be secured to a .10" spacer panel and a 1/4" thick backer panel, which slides into the trim. Assemble the panels with glue and screws: • Center the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue.
C
Freezer Drawer Panel
• Refer to the chart for locating the backer panel to the overlay panel. Secure the overlay panel to the backer panel with glue and screws. Screws must be countersunk into the backer panel
D
Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight – 25 lbs.
1/2" OVERLAY PANEL ROUTING DIMENSIONS
Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of 4" wide.
Grille Back
C
ZIC360NHLH
Door
A
D
C
1/2" Overlay Panel
B
Hinge Side
Door Panel Back
1/4" Backer Panel
.10" Spacer
Backer with Overlay Panel Assembly
PANEL DIMENSIONS A A
C
A
D
B
B
C
D
Fresh Food Panel 2 1/16"
2 1/16"
5/16"
3/16"
Freezer Panel
2 1/16"
2 1/16"
5/16"
3/16"
Grille Panel
2 1/16"
2 1/16"
1 11/16"
3/16"
Freezer Drawer
D
B
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR 3/4" OR 1/2" DUAL INSTALLATIONS 75" (190.5) Finished Width
4 5/16"
A
(10.9)
5 1/2"
ELEC. 9"
NOTES
5 1/2"
ELEC.
(13.9)
FLUSH INSET INSTALLATION
26 3/16" (66.5) Min. Cutout Depth
24 3/16" (61.4)
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims. A A separate 115V, 60Hz, 15- or 20-amp power supply is recommended for each product.
(13.9)
9"
(22.9)
(22.9)
85"
(215.9) Finished Opening
75 1/2"
(191.8 ) From floor to bottom of electrical area
WATER 7"
WATER
3 1/2" (9.0)
3 1/2" (9.0)
7 1/2" 7 1/2"
(17.8)
(19.1)
7" 3 1/2"
(19.1)
(17.8)
(8.9)
3 1/2"
W
SIDE VIEW
FRONT VIEW 15" (38.1) min
15" (38.1) min
1"
To wall
To wall
(2.5)
FLUSH INSET 1/2" PANEL DIMENSIONS DUAL INSTALLATION A B
Grille Panel
115˚ Door swing
Fresh Food Panel
Fresh Food Panel
Door Handles Door handles not included. Custom handles supplied by your cabinet maker may be used. ZKHPSS1: Professional tubular stainless steel handle designed to fit custom panels. Kit includes one handle – 30-1/2" long. Order 2 kits from your Monogram supplier.
Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs.
C
ZKHCT: Handle side trim for left-hand and right-hand door. For use on a custom panel when using a custom handle.
Freezer Drawer Panel
Freezer Drawer Panel
(8.9)
Maximum total panel weight: • Fresh food door panels – 58 lbs. • Freezer drawer panel – 28 lbs. • Unified grille panel – 25 lbs
ZKHCSS2: Custom European tubular handle designed to fit custom panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16".
E
115˚ Door swing
ZIC360NHLH
The 1/2" overlay panel must be secured to a .10" spacer panel and a 1/4" thick backer panel, which slides into the trim.
D
PANEL DIMENSIONS A
B
1/4" Backer Panel
69 7/8"
8 7/8"
46 1/16" 21 7/8"
C
D
33 7/8"
E
.10" Space Panel
68 1/2"
7 5/8" 44 11/16" 20 1/2"
32 1/2"
1/2" Overlay Panel
74 1/2" 10 11/16" 46 9/16" 22 7/16" 36 7/8"
ZIC360NHLH_ZIC360NHRH
Assemble the panels with glue and screws: • Center the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue. • Refer to the chart for locating the backer panel to the overlay panel. Secure the overlay panel to the backer panel with glue and screws. Screws must be countersunk into the backer panel
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR FLUSH INSET 3/4" PANEL DIMENSIONS DUAL INSTALLATION
FLUSH INSET INSTALLATION
A
PANEL DIMENSIONS
B
Grille Panel
A
B
C
D
E
74 1/2" 10 11/16" 46 9/16" 22 7/16" 36 7/8" E Fresh Food Panel
Fresh Food Panel
Freezer Drawer Panel
Freezer Drawer Panel
C
D
DETAIL TOP NOTE: Routed areas should be finished as they may be visible when assembled. 1/4"
7/16"
ZKHPSS1: Professional tubular stainless steel handle designed to fit custom panels. Kit includes one handle – 30-1/2" long. Order 2 kits from your Monogram supplier.
Front
ZKHCSS2: Custom European tubular handle designed to fit custom panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16".
Back
Back
Front
CORNER VIEW SHOWING “PICTURE FRAME” ROUTING
DETAIL HINGE SIDE
Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs. ZKHCT: Handle side trim for left-hand and right-hand door. For use on a custom panel when using a custom handle.
3/16"
DETAIL BOTTOM
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims.
Door Handles Door handles not included. Custom handles supplied by your cabinet maker may be used.
TOP
3/4"
NOTES
Maximum total panel weight: • Fresh food door panels – 58 lbs. • Freezer drawer panel – 28 lbs. • Unified grille panel – 25 lbs
3/4" RAISED DOOR AND DRAWER PANEL ROUTING (SEE PAGE 5 FOR 3/4" GRILLE PANEL ROUTING DIAGRAMS)
11/32" 1/4"
ZIC360NHLH
DETAIL HANDLE SIDE ROUTER DEPTH 1/4"
2 1/16"
3/16"
Front HINGE SIDE
HANDLE SIDE Back
3/4" PANEL BOTTOM VIEW (AFTER ROUTING)
BOTTOM
3/4" PANEL SIDE VIEW (AFTER ROUTING)
Product Specification Revised 1/18
WATER 3 1/2"
WATER 3 1/2"
7" 3 1/2" MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR 7"
(9.0)
(17.8)
7 1/2" 7 1/2" (19.1)
(9.0)
(19.1)
(17.8)
(8.9)
3 1/2"
W
3/4" OR 1/2" DUAL PRODUCT FRONT VIEW CLEARANCES 15" (38.1) min
15" (38.1) min
1"
To wall
SIDE VIEW
ZIC360NHLH
(8.9)
FLUSH INSET INSTALLATION
To wall
(2.5)
NOTES
115˚ Door swing
115˚ Door swing
A In a side-by-side installation of a left-and-right-hand door swing product, 1" clearance between the units is required. Order ZUG2 custom panel unified grille kit for this installation.
A
ZIC360NHLH_ZIC360NHRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR OVERALL DIMENSIONS AFTER PANEL INSTALL
ZIC360NHLH
STANDARD INSTALLATION 25 1/4" (64.1) 25 1/4" (64.1) 23 7/8" (60.7) 23 7/8" (60.7)
36" (91.5) 36" (91.5) 1 7/8" (4.8) 1 7/8"
9 7/8" (25.1) 9 7/8"
(4.8)
(25.1)
46 1/4" 46 (117.5) 1/4"
* 84" 84" * (213.4)
* 83 1/2" * 83(212.1) 1/2"
(117.5)
(213.4)
(212.1)
*73 1/4" *73(186.1) 1/4" (186.1)
*26" (66.0) *26" (66.0) *24 1/8" *26 1/2" 1/2" *24 (61.3) 1/8" *26 (16.5)
SPECIFICATIONS Overall Width
36" (91.4 cm)
Overall Height
84" (213.4 cm)
Overall Depth
25 3/8" (64.5 cm)
Door Clearance
36 3/4" (93.4 cm)
Cutout Width
35 1/2" (90.2 cm)
Cutout Height
83 1/2" - 84 1/2" (212.1 - 214.6 cm)
Cutout Depth
24" (61 cm)
Plumbing Requirements
1/4" OD copper tubing or GE SmartConnect kit
Shipping Weight
640 lb (290.3 kg)
(61.3)
FRONT VIEW VIEW * Shipping height.FRONT Use leveling legs and wheels for maximum
* Shipping Use leveling legs andheight. wheels for maximum 1" heightheight. adjustment from shipping 1" height adjustment from shipping height.
*3 5/8" (9.2) *3 5/8" (9.2)
SIDE VIEW SIDE VIEW
35" (89.0) Case width 35" (89.0)
Case width
** Allow 25" (63.5) min clearance for 130˚ ** Allow 25" (63.5) min door swing clearance for 130˚ door swing
TOP VIEW TOP VIEW
ATTENTION ELECTRICIAN: A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.
(16.5)
36 3/4" (93.4) 36 3/4" (93.4)
** Allow 4" (10.2) min clearance to amin wall ** Allow 4" (10.2) for 90˚ door clearance to aswing wall for 90˚ door swing
** These refrigerators are equipped with a 3-position door stop. The factory-set 130° door ** These are equipped 3-position stop. The factory-setto 130° door swingrefrigerators can be adjusted to 90° orwith 130°afor standarddoor installation if clearances adjacent swing can or bewalls adjusted to 90° or Allow 130° for standard installation if clearances to adjacent cabinets is restricted. a 15" minimum clearance to wall for pan removal. cabinets ordoor wallsstop is restricted. 15" access minimum clearance tobut wall forremoval pan removal. If the 90° position isAllow used,apan is maintained, pan is restricted. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted.
Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimension may vary due to manufacturing tolerances.
ZIC360NXLH ZIC360NXLHProduct Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR STANDARD INSTALLATION
STANDARD INSTALLATION 3"
35 1/2" (90.2)
2 5/16"
24" (61.0)
(7.6)
3 1/8"
(3.8)
6"
(15.2)
24" (61) 10" 1 9/16" (25.4)
(7.93)
7/16" (1.1) Trim overlap
TOP VIEW 1 1/2"
(5.9)
ELEC.
(3.97)
7/16" (1.1)
A
(5.874)
ELEC.
(212.1-214.6) *Trim will overlap additional 7/16"
B Water supply area.
6"
(15.24)
WARNING:
10"
(25.4)
75"
(190.5 ) From floor to bottom of electrical area
75"
*84 1/2"
(190.5 ) From floor to bottom of electrical area
(214.6) *Trim will overlap additional 7/16"
WATER 3 1/2"
(12.7)
5" 3 1/2"
(9.0)
(12.7)
B 10"(25.4)
(8.9)
WATER 3 1/2"WATER (9.0) 5" 3 1/2"
5"
(12.7)
3 1/2"
FRONT W VIEW
(8.9)
(12.7)
(8.9)
SIDE VIEW
FRONT VIEW
SIDE VIEW
NOTES A M ounting the junction box in this location will also allow for front accessibility through access panel.
35 1/2" (90.2)
2 5/16"
Trim overlap
*83 1/2" min *84 1/2" max
5"
ZIC360NHLH
ANTI-TIP BRACKET CL
Bracket mounted into vertical wall studs centered within the cutout Ensure holes selected are centered on the studs
Use two additional hole locations at end of brackets
81 1/2"
Wall Studs
(207.0)
STANDARD INSTALLATION ZIC360NHLH_RH
The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the antitip system you must use the product installation instructions. The information below applies to all installation constructions: • A wall bracket, bolts and toggles will be supplied with the unit. • The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. • The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. • In installation opening, measure 81-1/2" from floor and draw a horizontal line. • Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated. • The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. • When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts. See Installation Instructions for detailed instructions.
SIDE VIEW INSTALLED WITH ANTI-TIP BRACKET
FRONT VIEW OF CUTOUT WITH ANTI-TIP BRACKET
ZIC360NXRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR STANDARD 1/4" FRAMED PANEL DIMENSIONS SINGLE INSTALLATION
STANDARD INSTALLATION
A Grille Panel
NOTES B
Trim
Door
1/4" Framed Panel
Supplied Handles
Fresh Food Panel
Freezer Drawer Panel
ZIC360NHLH
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed custom door and grille panels are required. 1/4" Framed Panels:
C
For 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. Maximum total panel weight: • Fresh food door panel – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs.
D
A 1/4" Framed Panel
B
C
D
33 7/8" 8 7/8" 46 1/16" 21 7/8"
3/4" Overlay Panels:
STANDARD 3/4" OVERLAY PANEL DIMENSIONS SINGLE INSTALLATION A Grille Panel
B
Trim
Door
1/4" Backer Panel
3/4" Overlay Panel
.10" Spacer Panel
Supplied Handles
Fresh Food Panel
NOTE: Left-to-right offset is not always equal to top-to-bottom offset.
C
Maximum total panel weight: • Fresh food door panel – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs.
D
Door Handles: The supplied handles can be adjusted to accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker, can also be installed.
A 1/4" Backer Panel
Freezer Drawer Panel
The decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels. Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.
B
33 7/8" 8 7/8"
C
D
46 1/16" 21 7/8"
.10" Spacer Panel
32 1/2" 7 5/8" 44 11/16" 20 1/2"
3/4" Overlay Panel
34 1/8"
9"
46 5/16"
22"
ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" overlay panels. ZKHCSS2: European tubular handle designed to fit 3/4" panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16".
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR CUSTOM SIDE PANELS 24" (61.0)
F
ZIC360NHLH
STANDARD INSTALLATION NOTES
3/16" (.5)
1 7/8" (4.8)
*84"
(213.4) *Depending on installation height
F S ide panels must be used whenever the sides of the refrigerator will be exposed. The 1/4" side panels will slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer.
*3"- 4"
(7.6 - 10.2) *Depending on installation height
2 9/16" (6.5)
XRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRH XRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR DUAL INSTALLATIONS
STANDARD INSTALLATION
A
71 1/2" (181.6) Finished Width
2 5/16" 6"
10"
(15.2)
Additional cutout width may be required when side panels are used.
10"
(25.4)
NOTES A A separate 115V, 60Hz, 15- or 20-amp power supply is recommended for each product.
6"
ELEC.
(15.2)
24" (60.9) Min. Cutout Depth
24 3/16" (61.4)
(5.9)
ELEC.
ZIC360NHLH
(25.4)
83 1/2" min 84 1/2" max
(212.1-214.6) Finished Opening
75"
(190.5 ) From floor to bottom of electrical area
WATER
WATER
3 1/2" (9.0)
5"
3 1/2" (9.0)
5 3/4" 5 3/4"
(12.7)
(14.6)
5" 3 1/2"
(14.6)
(12.7)
10" (25.4)
(8.9)
WATER
SIDE VIEW
FRONT VIEW 25" min
25" min
1" (63.5) STANDARD 1/4" FRAMED PANEL To(63.5) (2.5) To wall wall DIMENSIONS DUAL INSTALLATION A
B
Grille Panel
PANEL DIMENSIONS E
130˚ Door swing
130˚ Door swing
Fresh Food Panel
Fresh Food Panel
Freezer Drawer Panel
1/4" Framed Panel
C
Freezer Drawer Panel
A
69 7/8"
B
8 7/8"
C
46 1/16"
D
21 7/8"
E
33 7/8"
D
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed custom door and grille panels are required. 1/4" Framed Panels: For 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. Maximum total panel weight: • Fresh food door panel – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 25 lbs. Order ZUG2: Unified grille kit for dual installation
PANEL ASSEMBLY CROSS SECTION
Door
Supplied Handles
Trim
1/4" Framed Panel
ZIC360NXLH_ZIC360NXRH_ZICP360NXLH_ZICP360NXRH ZICS360NXLH_ZICS360NXRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR STANDARD 3/4" OVERLAY PANEL DIMENSIONS DUAL INSTALLATION PANEL DIMENSIONS A
Fresh 2 5/16"Food (5.9) Panel
.10" 3/4" Spacer Overlay Panel Panel
A
69 7/8"
68 1/2"
70 1/8"
E
B
8 7/8"
7 5/8"
9"
71 1/2" Fresh(181.6)
C
Finished Width
Food Panel
6"
ELEC.
STANDARD INSTALLATION
1/4" Backer Panel
B
Grille Panel
24 3/16" C (61.4) 6"
ELEC.
(15.2)
10"
D
46 1/16" 44 11/16" 46 24"5/16" (60.9) Min. 21 7/8" 20 1/2" Cutout 22"Depth
E
33 7/8"
32 1/2"
34 1/8"
.25" + .10" + .75" = 1.10" Total Panel Thickness
(15.2)
10"
(25.4)
(25.4)
75"
From floor toBacker bottomPanel 1/4" of electrical area
3/4" Overlay Panel
Door Handles: The supplied handles can be adjusted to accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker, can also be installed.
.10" Spacer Panel
Supplied Handles
5"
3 1/2" (9.0)
(12.7)
WATER 5 3/4" 5 3/4" (14.6)
3 1/2" (9.0)
(14.6)
5" 3 1/2"
(12.7)
(8.9)
10" (25.4)
WATER
DUAL PRODUCT CLEARANCES A
25" min
25" min
1"
(63.5) To wall
SIDE VIEW
FRONT VIEW (63.5) To wall
(2.5)
The decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels. Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.
Order ZUG2: Unified grille kit for dual installation
Trim (190.5 )
Door
WATER
3/4" Overlay Panels:
Maximum total panel weight: • Fresh food door panel – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 25 lbs.
(212.1-214.6) Finished Opening
PANEL ASSEMBLY CROSS SECTION
NOTES
NOTE: Left-to-right offset is not always equal to top-to-bottom offset.
D
Freezer Drawer Panel
Freezer Drawer Panel
83 1/2" min 84 1/2" max
ZIC360NHLH
ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" overlay panels. ZKHCSS2: European tubular handle designed to fit 3/4" panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16". A In a side-by-side installation of a left-and-right-hand door swing product, 1" clearance between the units is required. Order ZUG2: custom panel unified grille kit for one continuous grille panel.
130˚ Door swing
130˚ Door swing
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR
ZIC360NHLH
FEATURES AND BENEFITS CUSTOM APPEARANCE Allows personalization with cabinet-compatible panels an custom handles UPFRONT ELECTRONIC CONTROLS WITH DIGITAL READOUT Allows precise temperature settings and are positioned for maximum ease of use HUMIDITY CONTROLLED VEGETABLE COMPARTMENTS AND SEALED SNACK PANS Help maintain freshness and help preserve foods longer ADJUSTABLE, SPILL PROOF GLASS SHELVES Make it easy to customize storage to handle foods and containers of various sizes 2 SEALED DELI PANS WITH FULL-EXTENSION SLIDES SIX ADJUSTABLE DOOR BINS Offer added storage flexibility GE WATER™ FILTRATION SYSTEM Delivers clean, great tasting ice
R
Product Specification Revised 1/18
ZIC360NHLH
SECTION 1
FLUSH INSET INSTALLATION
SECTION 2
STANDARD INSTALLATION 1/4" FRAMED PANELS
3/4" OVERLAY PANELS
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR OVERALL DIMENSIONS AFTER PANEL INSTALL
ZIC360NHLH
FLUSH INSET INSTALLATION 26" (66.0) 20 5/8" (52.4)
38" (96.5)
11 1/2" (29.2)
* 84 1/2"
* 83 1/2" (212.1)
(214.6)
*73"
(185.4)
SPECIFICATIONS
*26 7/16" (67.1)
Overall Width
38" (96.5 cm)†
Overall Height
84 1/2" (214.6 cm)†
Overall Depth
26" (66.0 cm)†
Door Clearance
38 3/4" (98.4 cm)
Cutout Width
39" (99.1 cm)
Cutout Height
85" (215.9 cm)
Cutout Depth
26 3/16" (66.5 cm)
Plumbing Requirements
1/4" OD copper tubing or GE SmartConnect kit
Shipping Weight
640 lb (290.3 kg)
FRONT VIEW
*4"
*4"
SIDE VIEW
(10.2)
(10.2)
* Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height. Nominal installation height is 84”
35" (89.0) Case width
Allow 15" (38.1) min clearance for 115˚ door swing
† Dimensions include 3/4" custom cabinet panel
TOP VIEW ATTENTION ELECTRICIAN: A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.
38 3/4" (98.4)
Allow 4" (10.2) min clearance to a wall for 90˚ door swing
Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimensions may vary due to manufacturing tolerances. Product Specification Revised 1/18 ZIC360NHLH
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR FLUSH INSET INSTALLATION 3/4" PANELS
ZIC360NHLH
FLUSH INSET INSTALLATION
TOP VIEW Case
5 1/4" (13.3)
35 1/2" (90.2)
2 5/16" (5.9)
6"
ELEC.
Flush inset depth
10" 20 15/16" (25.4) (53.2) *83 1/2" min *84 1/2" max
3/4" (1.9)
Depth to cleat
Width of side cleats
39" (99.1) Flush inset width 37 1/2" (95.3) Width between cleats
(212.1-214.6) *Trim will overlap additional 7/16"
10"
75"
(25.4)
(190.5 ) From floor to bottom of electrical area
(15.2)
(61.4)
75 1/2"
WATER 3 1/2"
5"
(12.7)
(191.8 ) From floor to bottom of electrical area
(213.4) height to cleat
(215.9)
5" 3 1/2"
(9.0)
(12.7)
7"
(17.8)
3 1/2"
FRONT VIEW (8.9)
SIDE VIEW
B WATER 3 1/2" (9.0)
WATER 7" (17.8) 3 1/2"
SIDE VIEW
W
A M ounting the junction box in this location will also allow for front accessibility through access panel. B Water supply area. WARNING:
The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions. The information below applies to all installation constructions:
10"(25.4)
(8.9)
NOTES
The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury.
24 3/16"
84"
85"
A
6"
ELEC.
Finished cleats
7/16" (1.1) Trim overlap
1/2" (1.3)
3/4" Panel
(15.2)
26 3/16" (66.5)
3"Finished cleats 24" (61.0) (7.6) Case Trim 1 1/2" (3.8) Door
(8.9)
FRONT VIEW
• A wall bracket, bolts and toggles will be supplied with the unit. • The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. • The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs.
ANTI-TIP BRACKET
CL
Use two additional hole locations at end of brackets
FLUSH INSTALLATION 81 1/2" ZIC360NHLH_RH (207.0)
Bracket mounted into vertical wall studs centered within the cutout Ensure holes selected are centered on the studs
Wall Studs
• In installation opening, measure 82" from floor and draw a horizontal line. • Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated. • The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. • When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts. See Installation Instructions for detailed instructions.
SIDE VIEW INSTALLED WITH ANTI-TIP BRACKET
FRONT VIEW OF CUTOUT WITH ANTI-TIP BRACKET
ZIC360NXRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR FLUSH INSET 3/4" PANEL DIMENSIONS SINGLE INSTALLATION
FLUSH INSET INSTALLATION
A
PANEL DIMENSIONS
B
Grille Panel
A 38"
Fresh Food Panel
B
C
NOTES
D
10 11/16" 46 9/16" 22 7/16"
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims.
C
D
Freezer Drawer Panel
ZIC360NHLH
Maximum total panel weight: • Fresh food door panels – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of 4" wide.
3/4" RAISED DOOR PANEL ROUTING TOP
DETAIL TOP NOTE: Routed areas should be finished as they may be visible when assembled.
3/4" 11/32" 1/4" 1/4"
7/16"
Door Handles Door handles not included. Custom handles supplied by your cabinet maker may be used.
Front
ZKHPSS1: Professional tubular stainless steel handle designed to fit custom panels. Kit includes one handle – 30-1/2" long. Order 2 kits from your Monogram supplier.
Back Back
Front
Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs.
1/4"
CORNER VIEW SHOWING “PICTURE FRAME” ROUTING
DETAIL BOTTOM
DETAIL LEFT SIDE
ZKHCSS2: Custom European tubular handle designed to fit custom panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16".
ZKHCT: Handle side trim for left-hand and right-hand door. For use on a custom panel when using a custom handle.
DETAIL RIGHT SIDE ROUTER DEPTH 1/4"
ROUTER DEPTH 1/4" 3/32" 1/4"
2-1/16"
2-1/16" Front
LEFT SIDE
RIGHT SIDE Back
3/4" PANEL BOTTOM VIEW (AFTER ROUTING)
BOTTOM
3/4" PANEL SIDE VIEW (AFTER ROUTING)
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR 3/4" RAISED GRILL PANEL ROUTING NOTE: Routed areas should be finished as they may be visible when assembled.
DETAIL TOP
FLUSH INSET INSTALLATION
TOP
NOTES
Front
1-11/16" ROUTER DEPTH 1/4"
Back Back
Front
CORNER VIEW SHOWING “PICTURE FRAME” ROUTING DETAIL LEFT SIDE
DETAIL RIGHT SIDE ROUTER DEPTH 1/4"
ROUTER DEPTH 1/4" 3/32"
BOTTOM
1/4"
3/16"
2-1/16"
3/4" PANEL SIDE VIEW (AFTER ROUTING)
2-1/16"
DETAIL BOTTOM
Front LEFT SIDE Back
3/4" RAISED DRAWER PANEL ROUTING
ZKHPSS1: Professional tubular stainless steel handle designed to fit custom panels. Kit includes one handle – 30-1/2" long. Order 2 kits from your Monogram supplier.
TOP
NOTE: Routed areas should be finished as they may be visible when assembled.
11/32" 1/4" 1/4"
Maximum total panel weight: • Fresh food door panels – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs
Door Handles Door handles not included. Custom handles supplied by your cabinet maker may be used.
3/4" PANEL BOTTOM VIEW (AFTER ROUTING)
3/4"
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims.
Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of 4" wide.
RIGHT SIDE
DETAIL TOP
ZIC360NHLH
ZKHCSS2: Custom European tubular handle designed to fit custom panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16".
Front
7/16"
Back Back
Front
Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs. ZKHCT: Handle side trim for left-hand and right-hand door. For use on a custom panel when using a custom handle.
1/4"
CORNER VIEW SHOWING “PICTURE FRAME” ROUTING DETAIL BOTTOM DETAIL LEFT SIDE
DETAIL RIGHT SIDE
ROUTER DEPTH 1/4"
ROUTER DEPTH 1/4"
2 1/16"
2 1/16" Front
LEFT SIDE
RIGHT SIDE
BOTTOM
Back
3/4" PANEL BOTTOM VIEW (AFTER ROUTING)
3/4" PANEL SIDE VIEW (AFTER ROUTING)
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR FLUSH INSET INSTALLATION 1/2" PANELS
FLUSH INSET INSTALLATION
TOP VIEW 35 1/2" (90.2)
2 5/16"
5 3/8" (13.7)
(5.9)
3"
Case (7.6) Finished cleats
24" (61.0) 1 1/2"
Case Trim
26 3/16" (66.5) Flush inset depth 10" (25.4) 20 13/16" (52.9) *83 1/2" min Depth to cleat *84 1/2" max
7/16" (1.1) Trim overlap
(3.8)
Door
6"
ELEC.
(15.2)
1/2" (1.3)
1/2" Panel
3/4" (1.9)
Width of side cleats
39" (99.1) Flush inset width 37 1/2" (95.3) Width between cleats
(212.1-214.6) *Trim will overlap additional 7/16"
10"
75"
(25.4)
(190.5 ) From floor to bottom of electrical area
Finished cleats
The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury.
24 3/16" (61.4)
75 1/2"
WATER 3 1/2"
5"
(12.7)
(9.0)
(191.8 ) From floor to bottom of electrical area
(213.4) height to cleat
(215.9)
5" 3 1/2"
(12.7)
(8.9)
7"
(17.8)
3 1/2" FRONT VIEW (8.9)
SIDE VIEW
B WATER 3 1/2" (9.0)
The information below applies to all installation constructions:
WATER
• A wall bracket, bolts and toggles will be supplied with the unit.
7"
(17.8)
3 1/2" (8.9)
FRONT VIEW
ANTI-TIP BRACKET
CL
Use two additional hole locations at end of brackets
FLUSH INSTALLATION ZIC360NHLH_RH 81 1/2" (207.0)
The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions.
10"(25.4)
SIDE VIEW
W
A M ounting the junction box in this location will also allow for front accessibility through access panel. B Water supply area. WARNING:
(15.2)
84"
85"
NOTES
A
6"
ELEC.
ZIC360NHLH
Bracket mounted into vertical wall studs centered within the cutout Ensure holes selected are centered on the studs
Wall Studs
• The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. • The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. • In installation opening, measure 82" from floor and draw a horizontal line. • Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated. • The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. • When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts. See Installation Instructions for detailed instructions.
SIDE VIEW INSTALLED WITH ANTI-TIP BRACKET
FRONT VIEW OF CUTOUT WITH ANTI-TIP BRACKET
ZIC360NXRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR FLUSH INSET 1/2" PANEL DIMENSIONS A
FLUSH INSET INSTALLATION
PANEL DIMENSIONS A
B
1/4" Backer Panel
33 7/8"
8 7/8"
.10" Space Panel
32 1/2"
7 5/8" 44 11/16" 20 1/2"
38"
10 11/16" 46 9/16" 22 7/16"
B
Grille Panel
1/2" Overlay Panel
Fresh Food Panel
C
D
NOTES
46 1/16" 21 7/8"
The 1/2" overlay panel must be secured to a .10" spacer panel and a 1/4" thick backer panel, which slides into the trim. Assemble the panels with glue and screws: • Center the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue.
C
Freezer Drawer Panel
• Refer to the chart for locating the backer panel to the overlay panel. Secure the overlay panel to the backer panel with glue and screws. Screws must be countersunk into the backer panel
D
Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight – 25 lbs.
1/2" OVERLAY PANEL ROUTING DIMENSIONS
Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of 4" wide.
Grille Back
C
ZIC360NHLH
Door
A
D
C
1/2" Overlay Panel
B
Hinge Side
Door Panel Back
1/4" Backer Panel
.10" Spacer
Backer with Overlay Panel Assembly
PANEL DIMENSIONS A A
C
A
D
B
B
C
D
Fresh Food Panel 2 1/16"
2 1/16"
5/16"
3/16"
Freezer Panel
2 1/16"
2 1/16"
5/16"
3/16"
Grille Panel
2 1/16"
2 1/16"
1 11/16"
3/16"
Freezer Drawer
D
B
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR 3/4" OR 1/2" DUAL INSTALLATIONS 75" (190.5) Finished Width
4 5/16"
A
(10.9)
5 1/2"
ELEC. 9"
NOTES
5 1/2"
ELEC.
(13.9)
FLUSH INSET INSTALLATION
26 3/16" (66.5) Min. Cutout Depth
24 3/16" (61.4)
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims. A A separate 115V, 60Hz, 15- or 20-amp power supply is recommended for each product.
(13.9)
9"
(22.9)
(22.9)
85"
(215.9) Finished Opening
75 1/2"
(191.8 ) From floor to bottom of electrical area
WATER 7"
WATER
3 1/2" (9.0)
3 1/2" (9.0)
7 1/2" 7 1/2"
(17.8)
(19.1)
7" 3 1/2"
(19.1)
(17.8)
(8.9)
3 1/2"
W
SIDE VIEW
FRONT VIEW 15" (38.1) min
15" (38.1) min
1"
To wall
To wall
(2.5)
FLUSH INSET 1/2" PANEL DIMENSIONS DUAL INSTALLATION A B
Grille Panel
115˚ Door swing
Fresh Food Panel
Fresh Food Panel
Door Handles Door handles not included. Custom handles supplied by your cabinet maker may be used. ZKHPSS1: Professional tubular stainless steel handle designed to fit custom panels. Kit includes one handle – 30-1/2" long. Order 2 kits from your Monogram supplier.
Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs.
C
ZKHCT: Handle side trim for left-hand and right-hand door. For use on a custom panel when using a custom handle.
Freezer Drawer Panel
Freezer Drawer Panel
(8.9)
Maximum total panel weight: • Fresh food door panels – 58 lbs. • Freezer drawer panel – 28 lbs. • Unified grille panel – 25 lbs
ZKHCSS2: Custom European tubular handle designed to fit custom panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16".
E
115˚ Door swing
ZIC360NHLH
The 1/2" overlay panel must be secured to a .10" spacer panel and a 1/4" thick backer panel, which slides into the trim.
D
PANEL DIMENSIONS A
B
1/4" Backer Panel
69 7/8"
8 7/8"
46 1/16" 21 7/8"
C
D
33 7/8"
E
.10" Space Panel
68 1/2"
7 5/8" 44 11/16" 20 1/2"
32 1/2"
1/2" Overlay Panel
74 1/2" 10 11/16" 46 9/16" 22 7/16" 36 7/8"
ZIC360NHLH_ZIC360NHRH
Assemble the panels with glue and screws: • Center the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue. • Refer to the chart for locating the backer panel to the overlay panel. Secure the overlay panel to the backer panel with glue and screws. Screws must be countersunk into the backer panel
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR FLUSH INSET 3/4" PANEL DIMENSIONS DUAL INSTALLATION
FLUSH INSET INSTALLATION
A
PANEL DIMENSIONS
B
Grille Panel
A
B
C
D
E
74 1/2" 10 11/16" 46 9/16" 22 7/16" 36 7/8" E Fresh Food Panel
Fresh Food Panel
Freezer Drawer Panel
Freezer Drawer Panel
C
D
DETAIL TOP NOTE: Routed areas should be finished as they may be visible when assembled. 1/4"
7/16"
ZKHPSS1: Professional tubular stainless steel handle designed to fit custom panels. Kit includes one handle – 30-1/2" long. Order 2 kits from your Monogram supplier.
Front
ZKHCSS2: Custom European tubular handle designed to fit custom panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16".
Back
Back
Front
CORNER VIEW SHOWING “PICTURE FRAME” ROUTING
DETAIL HINGE SIDE
Order ZUG2: Unified grille kit for dual installation. Maximum total panel weight - 25 lbs. ZKHCT: Handle side trim for left-hand and right-hand door. For use on a custom panel when using a custom handle.
3/16"
DETAIL BOTTOM
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims.
Door Handles Door handles not included. Custom handles supplied by your cabinet maker may be used.
TOP
3/4"
NOTES
Maximum total panel weight: • Fresh food door panels – 58 lbs. • Freezer drawer panel – 28 lbs. • Unified grille panel – 25 lbs
3/4" RAISED DOOR AND DRAWER PANEL ROUTING (SEE PAGE 5 FOR 3/4" GRILLE PANEL ROUTING DIAGRAMS)
11/32" 1/4"
ZIC360NHLH
DETAIL HANDLE SIDE ROUTER DEPTH 1/4"
2 1/16"
3/16"
Front HINGE SIDE
HANDLE SIDE Back
3/4" PANEL BOTTOM VIEW (AFTER ROUTING)
BOTTOM
3/4" PANEL SIDE VIEW (AFTER ROUTING)
Product Specification Revised 1/18
WATER 3 1/2"
WATER 3 1/2"
7" 3 1/2" MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR 7"
(9.0)
(17.8)
7 1/2" 7 1/2" (19.1)
(9.0)
(19.1)
(17.8)
(8.9)
3 1/2"
W
3/4" OR 1/2" DUAL PRODUCT FRONT VIEW CLEARANCES 15" (38.1) min
15" (38.1) min
1"
To wall
SIDE VIEW
ZIC360NHLH
(8.9)
FLUSH INSET INSTALLATION
To wall
(2.5)
NOTES
115˚ Door swing
115˚ Door swing
A In a side-by-side installation of a left-and-right-hand door swing product, 1" clearance between the units is required. Order ZUG2 custom panel unified grille kit for this installation.
A
ZIC360NHLH_ZIC360NHRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR OVERALL DIMENSIONS AFTER PANEL INSTALL
ZIC360NHLH
STANDARD INSTALLATION 25 1/4" (64.1) 25 1/4" (64.1) 23 7/8" (60.7) 23 7/8" (60.7)
36" (91.5) 36" (91.5) 1 7/8" (4.8) 1 7/8"
9 7/8" (25.1) 9 7/8"
(4.8)
(25.1)
46 1/4" 46 (117.5) 1/4"
* 84" 84" * (213.4)
* 83 1/2" * 83(212.1) 1/2"
(117.5)
(213.4)
(212.1)
*73 1/4" *73(186.1) 1/4" (186.1)
*26" (66.0) *26" (66.0) *24 1/8" *26 1/2" 1/2" *24 (61.3) 1/8" *26 (16.5)
SPECIFICATIONS Overall Width
36" (91.4 cm)
Overall Height
84" (213.4 cm)
Overall Depth
25 3/8" (64.5 cm)
Door Clearance
36 3/4" (93.4 cm)
Cutout Width
35 1/2" (90.2 cm)
Cutout Height
83 1/2" - 84 1/2" (212.1 - 214.6 cm)
Cutout Depth
24" (61 cm)
Plumbing Requirements
1/4" OD copper tubing or GE SmartConnect kit
Shipping Weight
640 lb (290.3 kg)
(61.3)
FRONT VIEW VIEW * Shipping height.FRONT Use leveling legs and wheels for maximum
* Shipping Use leveling legs andheight. wheels for maximum 1" heightheight. adjustment from shipping 1" height adjustment from shipping height.
*3 5/8" (9.2) *3 5/8" (9.2)
SIDE VIEW SIDE VIEW
35" (89.0) Case width 35" (89.0)
Case width
** Allow 25" (63.5) min clearance for 130˚ ** Allow 25" (63.5) min door swing clearance for 130˚ door swing
TOP VIEW TOP VIEW
ATTENTION ELECTRICIAN: A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.
(16.5)
36 3/4" (93.4) 36 3/4" (93.4)
** Allow 4" (10.2) min clearance to amin wall ** Allow 4" (10.2) for 90˚ door clearance to aswing wall for 90˚ door swing
** These refrigerators are equipped with a 3-position door stop. The factory-set 130° door ** These are equipped 3-position stop. The factory-setto 130° door swingrefrigerators can be adjusted to 90° orwith 130°afor standarddoor installation if clearances adjacent swing can or bewalls adjusted to 90° or Allow 130° for standard installation if clearances to adjacent cabinets is restricted. a 15" minimum clearance to wall for pan removal. cabinets ordoor wallsstop is restricted. 15" access minimum clearance tobut wall forremoval pan removal. If the 90° position isAllow used,apan is maintained, pan is restricted. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted.
Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimension may vary due to manufacturing tolerances.
ZIC360NXLH ZIC360NXLHProduct Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR STANDARD INSTALLATION
STANDARD INSTALLATION 3"
35 1/2" (90.2)
2 5/16"
24" (61.0)
(7.6)
3 1/8"
(3.8)
6"
(15.2)
24" (61) 10" 1 9/16" (25.4)
(7.93)
7/16" (1.1) Trim overlap
TOP VIEW 1 1/2"
(5.9)
ELEC.
(3.97)
7/16" (1.1)
A
(5.874)
ELEC.
(212.1-214.6) *Trim will overlap additional 7/16"
B Water supply area.
6"
(15.24)
WARNING:
10"
(25.4)
75"
(190.5 ) From floor to bottom of electrical area
75"
*84 1/2"
(190.5 ) From floor to bottom of electrical area
(214.6) *Trim will overlap additional 7/16"
WATER 3 1/2"
(12.7)
5" 3 1/2"
(9.0)
(12.7)
B 10"(25.4)
(8.9)
WATER 3 1/2"WATER (9.0) 5" 3 1/2"
5"
(12.7)
3 1/2"
FRONT W VIEW
(8.9)
(12.7)
(8.9)
SIDE VIEW
FRONT VIEW
SIDE VIEW
NOTES A M ounting the junction box in this location will also allow for front accessibility through access panel.
35 1/2" (90.2)
2 5/16"
Trim overlap
*83 1/2" min *84 1/2" max
5"
ZIC360NHLH
ANTI-TIP BRACKET CL
Bracket mounted into vertical wall studs centered within the cutout Ensure holes selected are centered on the studs
Use two additional hole locations at end of brackets
81 1/2"
Wall Studs
(207.0)
STANDARD INSTALLATION ZIC360NHLH_RH
The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the antitip system you must use the product installation instructions. The information below applies to all installation constructions: • A wall bracket, bolts and toggles will be supplied with the unit. • The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs. • The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs. • In installation opening, measure 81-1/2" from floor and draw a horizontal line. • Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated. • The bracket will be centered left to right in opening with bottom of bracket on the horizontal line. • When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts. See Installation Instructions for detailed instructions.
SIDE VIEW INSTALLED WITH ANTI-TIP BRACKET
FRONT VIEW OF CUTOUT WITH ANTI-TIP BRACKET
ZIC360NXRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR STANDARD 1/4" FRAMED PANEL DIMENSIONS SINGLE INSTALLATION
STANDARD INSTALLATION
A Grille Panel
NOTES B
Trim
Door
1/4" Framed Panel
Supplied Handles
Fresh Food Panel
Freezer Drawer Panel
ZIC360NHLH
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed custom door and grille panels are required. 1/4" Framed Panels:
C
For 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. Maximum total panel weight: • Fresh food door panel – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs.
D
A 1/4" Framed Panel
B
C
D
33 7/8" 8 7/8" 46 1/16" 21 7/8"
3/4" Overlay Panels:
STANDARD 3/4" OVERLAY PANEL DIMENSIONS SINGLE INSTALLATION A Grille Panel
B
Trim
Door
1/4" Backer Panel
3/4" Overlay Panel
.10" Spacer Panel
Supplied Handles
Fresh Food Panel
NOTE: Left-to-right offset is not always equal to top-to-bottom offset.
C
Maximum total panel weight: • Fresh food door panel – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 11 lbs.
D
Door Handles: The supplied handles can be adjusted to accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker, can also be installed.
A 1/4" Backer Panel
Freezer Drawer Panel
The decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels. Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.
B
33 7/8" 8 7/8"
C
D
46 1/16" 21 7/8"
.10" Spacer Panel
32 1/2" 7 5/8" 44 11/16" 20 1/2"
3/4" Overlay Panel
34 1/8"
9"
46 5/16"
22"
ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" overlay panels. ZKHCSS2: European tubular handle designed to fit 3/4" panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16".
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR CUSTOM SIDE PANELS 24" (61.0)
F
ZIC360NHLH
STANDARD INSTALLATION NOTES
3/16" (.5)
1 7/8" (4.8)
*84"
(213.4) *Depending on installation height
F S ide panels must be used whenever the sides of the refrigerator will be exposed. The 1/4" side panels will slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer.
*3"- 4"
(7.6 - 10.2) *Depending on installation height
2 9/16" (6.5)
XRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRH XRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR DUAL INSTALLATIONS
STANDARD INSTALLATION
A
71 1/2" (181.6) Finished Width
2 5/16" 6"
10"
(15.2)
Additional cutout width may be required when side panels are used.
10"
(25.4)
NOTES A A separate 115V, 60Hz, 15- or 20-amp power supply is recommended for each product.
6"
ELEC.
(15.2)
24" (60.9) Min. Cutout Depth
24 3/16" (61.4)
(5.9)
ELEC.
ZIC360NHLH
(25.4)
83 1/2" min 84 1/2" max
(212.1-214.6) Finished Opening
75"
(190.5 ) From floor to bottom of electrical area
WATER
WATER
3 1/2" (9.0)
5"
3 1/2" (9.0)
5 3/4" 5 3/4"
(12.7)
(14.6)
5" 3 1/2"
(14.6)
(12.7)
10" (25.4)
(8.9)
WATER
SIDE VIEW
FRONT VIEW 25" min
25" min
1" (63.5) STANDARD 1/4" FRAMED PANEL To(63.5) (2.5) To wall wall DIMENSIONS DUAL INSTALLATION A
B
Grille Panel
PANEL DIMENSIONS E
130˚ Door swing
130˚ Door swing
Fresh Food Panel
Fresh Food Panel
Freezer Drawer Panel
1/4" Framed Panel
C
Freezer Drawer Panel
A
69 7/8"
B
8 7/8"
C
46 1/16"
D
21 7/8"
E
33 7/8"
D
Trimmed refrigerators are designed to be customized with decorative panels. Field-installed custom door and grille panels are required. 1/4" Framed Panels: For 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim. Maximum total panel weight: • Fresh food door panel – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 25 lbs. Order ZUG2: Unified grille kit for dual installation
PANEL ASSEMBLY CROSS SECTION
Door
Supplied Handles
Trim
1/4" Framed Panel
ZIC360NXLH_ZIC360NXRH_ZICP360NXLH_ZICP360NXRH ZICS360NXLH_ZICS360NXRH
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR STANDARD 3/4" OVERLAY PANEL DIMENSIONS DUAL INSTALLATION PANEL DIMENSIONS A
Fresh 2 5/16"Food (5.9) Panel
.10" 3/4" Spacer Overlay Panel Panel
A
69 7/8"
68 1/2"
70 1/8"
E
B
8 7/8"
7 5/8"
9"
71 1/2" Fresh(181.6)
C
Finished Width
Food Panel
6"
ELEC.
STANDARD INSTALLATION
1/4" Backer Panel
B
Grille Panel
24 3/16" C (61.4) 6"
ELEC.
(15.2)
10"
D
46 1/16" 44 11/16" 46 24"5/16" (60.9) Min. 21 7/8" 20 1/2" Cutout 22"Depth
E
33 7/8"
32 1/2"
34 1/8"
.25" + .10" + .75" = 1.10" Total Panel Thickness
(15.2)
10"
(25.4)
(25.4)
75"
From floor toBacker bottomPanel 1/4" of electrical area
3/4" Overlay Panel
Door Handles: The supplied handles can be adjusted to accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker, can also be installed.
.10" Spacer Panel
Supplied Handles
5"
3 1/2" (9.0)
(12.7)
WATER 5 3/4" 5 3/4" (14.6)
3 1/2" (9.0)
(14.6)
5" 3 1/2"
(12.7)
(8.9)
10" (25.4)
WATER
DUAL PRODUCT CLEARANCES A
25" min
25" min
1"
(63.5) To wall
SIDE VIEW
FRONT VIEW (63.5) To wall
(2.5)
The decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels. Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.
Order ZUG2: Unified grille kit for dual installation
Trim (190.5 )
Door
WATER
3/4" Overlay Panels:
Maximum total panel weight: • Fresh food door panel – 58 lbs. • Freezer drawer panel – 28 lbs. • Grille panel – 25 lbs.
(212.1-214.6) Finished Opening
PANEL ASSEMBLY CROSS SECTION
NOTES
NOTE: Left-to-right offset is not always equal to top-to-bottom offset.
D
Freezer Drawer Panel
Freezer Drawer Panel
83 1/2" min 84 1/2" max
ZIC360NHLH
ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" overlay panels. ZKHCSS2: European tubular handle designed to fit 3/4" panels. Kit includes 2 handles. Door handle is 44-3/16" and drawer handle is 33-3/16". A In a side-by-side installation of a left-and-right-hand door swing product, 1" clearance between the units is required. Order ZUG2: custom panel unified grille kit for one continuous grille panel.
130˚ Door swing
130˚ Door swing
Product Specification Revised 1/18
MONOGRAM 36" BUILT-IN BOTTOM-FREEZER REFRIGERATOR
ZIC360NHLH
FEATURES AND BENEFITS CUSTOM APPEARANCE Allows personalization with cabinet-compatible panels an custom handles UPFRONT ELECTRONIC CONTROLS WITH DIGITAL READOUT Allows precise temperature settings and are positioned for maximum ease of use HUMIDITY CONTROLLED VEGETABLE COMPARTMENTS AND SEALED SNACK PANS Help maintain freshness and help preserve foods longer ADJUSTABLE, SPILL PROOF GLASS SHELVES Make it easy to customize storage to handle foods and containers of various sizes 2 SEALED DELI PANS WITH FULL-EXTENSION SLIDES SIX ADJUSTABLE DOOR BINS Offer added storage flexibility GE WATER™ FILTRATION SYSTEM Delivers clean, great tasting ice
R
Product Specification Revised 1/18
