Nikon Coolpix L840 Flash Replacement
Nikon Coolpix L840 Flash Replacement
Nikon Coolpix L840 Flash Replacement This guide shows how to access the camera's flash.
Written By: Chanelle Mosquera
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
Nikon Coolpix L840 Flash Replacement
INTRODUCTION This guide details the steps required to access and replace the camera's flash.
TOOLS: Phillips #000 Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
Nikon Coolpix L840 Flash Replacement
Step 1 — Flash
Press the flash button on the side of the camera to allow the flash to spring upward.
Step 2
Unscrew the two black, 4mm screws with a Philips 000. (There should be one screw on each side of the camera).
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 5
Nikon Coolpix L840 Flash Replacement
Step 3
Remove the back case of the flash by lifting it off of the flash.
The back half cover has a little tail that keeps it locked in place. Wiggling the back cover around may help unhook the tail.
Step 4
© iFixit — CC BY-NC-SA
www.iFixit.com
Push the flash inward to pop the flash out of its front case. Since the back case is removed, the flash should pop out from the back.
Page 4 of 5
Nikon Coolpix L840 Flash Replacement
Step 5
The see-through protective flash covering is stuck on to the flash with thin, double-sided tape. Pull apart the two components to access the flash.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-20 07:39:31 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
Nikon Coolpix L840 Flash Replacement This guide shows how to access the camera's flash.
Written By: Chanelle Mosquera
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
Nikon Coolpix L840 Flash Replacement
INTRODUCTION This guide details the steps required to access and replace the camera's flash.
TOOLS: Phillips #000 Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
Nikon Coolpix L840 Flash Replacement
Step 1 — Flash
Press the flash button on the side of the camera to allow the flash to spring upward.
Step 2
Unscrew the two black, 4mm screws with a Philips 000. (There should be one screw on each side of the camera).
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 5
Nikon Coolpix L840 Flash Replacement
Step 3
Remove the back case of the flash by lifting it off of the flash.
The back half cover has a little tail that keeps it locked in place. Wiggling the back cover around may help unhook the tail.
Step 4
© iFixit — CC BY-NC-SA
www.iFixit.com
Push the flash inward to pop the flash out of its front case. Since the back case is removed, the flash should pop out from the back.
Page 4 of 5
Nikon Coolpix L840 Flash Replacement
Step 5
The see-through protective flash covering is stuck on to the flash with thin, double-sided tape. Pull apart the two components to access the flash.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-20 07:39:31 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
