Oster 16-Speed Blender Fan and Motor Replacement
Oster 16-Speed Blender Fan and Motor Replacement
Oster 16-Speed Blender Fan and Motor Replacement This guide will show you how to remove the fan and motor from the blender in order to replace.
Written By: Dana
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 7
Oster 16-Speed Blender Fan and Motor Replacement
TOOLS: Phillips #2 Screwdriver (1) Smart Wrench (1) Solder (1) Soldering Station (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 7
Oster 16-Speed Blender Fan and Motor Replacement
Step 1 — Fan and Motor
Remove the Blender Container from the Blender Base.
Step 2
Flip the blender so the bottom is facing you.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 7
Oster 16-Speed Blender Fan and Motor Replacement
Step 3
Unscrew the 16mm screws located on the plastic bottom from the blender base using a Phillips #2 screwdriver.
Step 4
Remove the plastic bottom from the base of the blender.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 7
Oster 16-Speed Blender Fan and Motor Replacement
Step 5
Holding the center of the fan, grip the knob in the center of the top of the blender with a wrench and twist the wrench counterclockwise.
Step 6
© iFixit — CC BY-NC-SA
www.iFixit.com
Carefully remove the motor and fan from the base of the blender.
Page 5 of 7
Oster 16-Speed Blender Fan and Motor Replacement
Step 7
Now, gently pull the white wire that is connected to the base and the motor.
Be careful, as there is a spring behind the contact points, that might try to shoot out and hurt you. Step 8
Now, turn the motor over, and remove the black wire from the motor.
Again, be warned as the is another spring that wants to shoot out and hurt you here as well.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 7
Oster 16-Speed Blender Fan and Motor Replacement
Step 9
Now de-solder the yellow wire from circuit board. De-solder the wire following these instructions.
Be careful, as there is another, black wire, nearby that you do not want to de-solder. Now the fan and motor are ready for replacement. To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-25 04:21:37 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 7
Oster 16-Speed Blender Fan and Motor Replacement This guide will show you how to remove the fan and motor from the blender in order to replace.
Written By: Dana
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 7
Oster 16-Speed Blender Fan and Motor Replacement
TOOLS: Phillips #2 Screwdriver (1) Smart Wrench (1) Solder (1) Soldering Station (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 7
Oster 16-Speed Blender Fan and Motor Replacement
Step 1 — Fan and Motor
Remove the Blender Container from the Blender Base.
Step 2
Flip the blender so the bottom is facing you.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 7
Oster 16-Speed Blender Fan and Motor Replacement
Step 3
Unscrew the 16mm screws located on the plastic bottom from the blender base using a Phillips #2 screwdriver.
Step 4
Remove the plastic bottom from the base of the blender.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 7
Oster 16-Speed Blender Fan and Motor Replacement
Step 5
Holding the center of the fan, grip the knob in the center of the top of the blender with a wrench and twist the wrench counterclockwise.
Step 6
© iFixit — CC BY-NC-SA
www.iFixit.com
Carefully remove the motor and fan from the base of the blender.
Page 5 of 7
Oster 16-Speed Blender Fan and Motor Replacement
Step 7
Now, gently pull the white wire that is connected to the base and the motor.
Be careful, as there is a spring behind the contact points, that might try to shoot out and hurt you. Step 8
Now, turn the motor over, and remove the black wire from the motor.
Again, be warned as the is another spring that wants to shoot out and hurt you here as well.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 7
Oster 16-Speed Blender Fan and Motor Replacement
Step 9
Now de-solder the yellow wire from circuit board. De-solder the wire following these instructions.
Be careful, as there is another, black wire, nearby that you do not want to de-solder. Now the fan and motor are ready for replacement. To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-25 04:21:37 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 7
