Package Electric Heater Kits - Sears Parts Direct
H3HK Series
Package Electric Heater Kits Description Installation Conditioners
of 208/240V
and 460V
and Packaged
H3HK
Heater
Kits in Packaged
Air
Heat Pumps.
These instructions are primarily intended to assist qualified individuals experienced in the proper installation of heating and/or air conditioning appliances. Some local codes require licensed installation/service personnel for this type equipment. All installations must be in accordance with these instructions and with all applicable national and local codes and standards. Read these instructions thoroughly before starting the installation. warnings contained within these instructions and on the unit.
GENERAL
INFORMATION
The H3HK Heater Kits are approved for use in the Packaged Air Conditioners and Packaged Heat Pumps when applied and installed according to these instructions. See Table 3 or Table 4 for the approved H3HK air conditioner
Follow all precautions
and
combinations and the approved H3HK heat pump combinations. Refer to the National Electric Code (ANSI/NFPA 70) or in Canada the Canadian Electric Code Part 1 (CSA C.22.1) and applicable local codes for overcurrent protection and disconnect requirements.
ELECTRICAL
SUPPLY
Circuit Options -- The units with electric heat may be wired for single or multiple circuits and may have circuit breakers or terminal blocks.
WARNING: To
avoid
the
risk
of
electric
shock, personal injury, or death, disconnect all electrical power to the unit before performing any maintenance or service. The unit may have more than one
power
supply.
if the unit was previously installed without electric heat, the existing supply wiring may not be sufficient to handle the increased load. See the unit rating label or Tables 5 thru 8 for minimum circuit ampacities and maximum overcurrent protection ratings. The units with installed electric heat may be supplied by a single circuit or by multiple circuits. Additional accessory kits may be required if single circuit installation and/or circuit breakers are desired. See Table 1 for accessory descriptions and part numbers.
Installation Remove the control box access panel. Locate the 9 pin (12 pin for 3 phase kits) heater plug assembly and remove the jumper cap. Discard the jumper cap; it will not be used after installing the heater kits. Order Description
Number
208/240v 1 Phase Heater Kits H3HK005H-01A,
5kw, 1-Stage Heater Kit
917166B
H3HK008H-01A,
8kw, 1-Stage Heater Kit
917167B
H3HK010H-01A,
10kw, 1-Stage Heater Kit
917168B
H3HK015H-01A,
15kw, 1-Stage Heater Kit
917169B
H3HK015H-21A,
15kw, 1-Stage Heater Kit
917172B
H3HK020H-01A,
20kw, 1-Stage Heater Kit
917170B
H3HK020H-21A,
20kw, 1-Stage Heater Kit
917173B
Note: Circuit breakers installed in the unit are for short-circuit protection of the internal wiring and to serve as a unit disconnect. The circuit breakers DO NOT provide overcurrent protection of the supply wiring. Whether or not circuit breakers are used in the units, overcurrent protection must be provided at the branch circuit distribution panel and sized as shown in Tables 5 thru 8 or on the unit rating label and according to the National Electric Code, Canadian Electrical Code and applicable local codes, tn most cases the overcurrent protection specified on the unit rating label is less than the 60 amp rating of the circuit breakers used in the units. This is because the function of the overcurrent protection required at the distribution panel (field supplied) and the unit mounted breakers is different. When circuit breakers are used they must be used on all circuits. Refer to Table 3 or Table 4 for the correct number of circuit breakers to install. See Table 1 for the correct circuit breaker for the application. if the number of circuits as shown in Table 3 or Table 4 is more than one, circuit breakers are required, tf single circuit supply wiring is desired, use the 4-pole single circuit adapter kit (PIN 913350) when two 2-pole circuit breakers are used and the 6-pole single circuit adapter kit (PIN 913556) when three 2-pole circuit breakers are used. The single circuit adapter kits are not applicable to three phase units. if circuit breakers are not being used, proceed to the Terminal Block section. Circuit
208/240v 3 Phase Heater Kits H3HK-009Q-01A,
9kw, Heater Kit
903854B
H3HK-015Q-01A,
15kw, Heater Kit
903855B
Breakers -- If circuit breakers are used
for any circuit, they must be used for all circuits. Use one breaker for each circuit as shown in Table 3.
460v 3 Phase Heater Kits H3HK-009S-01A,
9kw, Heater Kit
903850B
H3HK-015S-01A,
15kw, Heater Kit
903851B
Breaker Attachment -- Install the circuit breaker mounting rail to the control panel with the 4 blunt tip screws provided.
Accessories: 4-Pole Single Circuit Adaptor*
913350
6-Pole Single Circuit Adaptor*
913556
Circuit Breaker, Single Phase (2-Pole)
913554
Circuit Breaker, Three Phase (3-Pole)
913740
*Single Phase Models Only
Table 1. Accessories 2
Attaching to BracketAttach the circuit breakers in the unit by hooking the bottom in the base of the circuit breaker onto the left rail of the bracket and rotating to the right. The circuit breaker should snap into place. Install the breakers so that the "ON" position is at the right.
SMALL
PACKAGE
RELAY /
ACCESS
HOLE
,,_CONTACTOR
BREAKERS"
I
ELECTRIC HEATING ELEMENTS
\
LIMIT SWmTCH
CONTACTOR
ol
LARGE
PACKAGE
TERMINAL BLOCKS (Se{ect ModeM) ACCESS HOLE
TERMINAL
CIRCUIT BREAKER BRACKET
CONTACTOR ELECTRIC HEATING ELEMENTS CIRCUIT BREAKERS
CONTACTORS
(Shown in position for downshot flow)
SINGLE CIRCUIT ADAPTER
Figure Breaker
Removal
--
1.
Location
Insert a screwdriver
into
the hole in the release tab and pull out while rotating the breaker out and to the left. The white release tab is located at the base of the breaker under the line side (right) terminals. Single Circuit Kit (single phase only) -- Refer to the instructions included with the single circuit adapter kit for details on how to configure the adapter. Install the adapter as shown in the instructions in the line side (right) of the breakers. Proceed to the Element Installation section. Terminal Blocks -- Approved H3HK heater kits are shipped with a terminal block for small package units. For large package units the terminal block(s) supplied with the kits will not be used. The electric heater kits will be wired to the existing factory installed terminal block, tf the number of circuits indicated in Table 3 or Table 4 is two or three, then the circuit breakers must be used; see the Circuit Breaker section.
of Major Components Element installation -- Remove the blower access panel. Remove the heater close-off plate(s) in the electric heat panel. When installing single banks of heaters, position them closest to the blower. Install the heater kit in the opening with the limit control towards the top of the unit if the unit is using the side supply and return duct openings. If the unit is using the downshot supply and return openings, install the heater kit in the opening with the limit towards the bottom of the unit. Make sure that the element support rod is inserted into the support bracket. Refer to Figure 2. Fasten the heater with the same screws used to secure the close-off plates. Staged Heat -- To stage the heat on the 15 kw or 20 kw Heater Kits the factory set wiring will need to be modified. The orange wire in Pin 2 on the Heat Accessory Plug will be re-routed. See the Typical AC (or HP) Thermostat Connection figure in the HP or AC Installation Instructions. 3
/ WARNING: Rooftop
applications
cal ducts must installed in the that the elements
over a supply
iMPORTANT: with verti=
have an elbow supply duct so are not directly
Torque the circuit breaker to 45 in=lbs, AIRFLOW
grille. The maximum external static pressure for the units are listed in Table 2.
WARNING: The heater will not function erly if the elements rectly installed. ELEMENT
lugs
are
prop-
not cor-
POWERWIRING
Route the main power leads (heavy black and red wires) and the 9 or 12-pin heat plug through the access hole at the top of the control panel to the circuit breaker or terminal block. Connect the 9 or 12-pin heat kit plug to the heat accessory plug located in the control box. Refer to the detailed wiring diagrams for connections. Make sure that the connections are secure. Select large package units have additional terminal blocks installed. The power leads from the heater kit should be attached to these terminal blocks. Wires needed to connect from terminal blocks to circuit breakers should be field supplied. The 6 inch leads are provided with the heater kit to connect the circuit breaker(s) to the compressor contactor. Mark the appropriate box on the unit rating plate with an "X" to indicate which heater kit has been installed. HEATING ELEMENTS
SUPPORT BRACKET
Y
(ESP)
The unit is factory shipped with a jumper wire between the heating speed contacts and the cooling speed contacts on the blower relay. If the heating/cooling speed desired is the preset speed, then no modifications are required. If a different heating/cooling speed is desired, remove the blower lead attached to terminal #4 on the relay (leave the jumper wire in place). Cut the wire tie retaining the unused motor speed taps and connect the desired motor tap to terminal #4 on the relay. Refer to Figure 3 for the motor lead color coding. For 460V units, refer to the wiring diagram on the blower motor to select a different blower speed. If a heating speed different from the cooling speed is desired, remove and discard the jumper wire from the blower relay. Cut the wire tie holding the unused speed taps. Connect the desired heating speed tap to pin #6 and the desired cooling speed tap on pin #4 of the blower relay, 208/230V units only. For 460V units only, one fan speed is obtainable for both heating and cooling. It is recommended that the fan be set for high speed operation when using electric auxiliary heat.
WARNING: After making any changes to the blower speed setting, be sure to bundle and insulate any unused speed taps so that they will not contact with cabinet or any uninsulated live parts, CLEARANCE
I% ¢_
®
Figure 2. Element
¢
®
Support
Bracket
All units are approved for zero clearance to combustibles when installed according to these instructions and other instructions included with the unit and other approved accessories.
208/230V
Units LARGE
1
PACKAGE
SMALL
PACKAGE
RED (LOW)
2 3
BLUE
4
BLACK
(MEDIUM)
BLACK
(HIGH)
- (HIGH)
DEFAULT
RED (LOW)
5 6 --
WHITE
(COMMON)
Figure 3. Blower
Motor Speed Tap Color Code
Three Phase
Single Phase Unit 2.5 & 3 Ton 10 & 12 SEER
3.5 & 4 Ton 10 & 12 SEER
5 Ton 10 & 12 SEER
Blower Speed
5kW
Low
0.3
8kW 10kV_ 15kW20kW 0.3
0.3
0.3
Medium
0.3
0.3
0.3
0.3
High
0.5
0.5
0.5
0.5
Low
0.3
0.3
0.3
0.3
0.3 0.5
0.3 0.5
0.3 0.5
0.3 0.5
Low
0.3
0.3
0.3
0.3
0.3
High
0.5
0.3 0.5
LARGE
Unit
0.3 0.5
0.3
4 Ton 10 SEER
5 Ton 10 SEER
0.3
0.5
5kW
Low
0.3
0.3
0.3
0.3
0.3
10& 12SEER
High
0.3
0.3
0.3
0.3
0.3
2-t/2 Ton
Low
0.3
0.3
0.3
0.3
0.3
10& 12SEER
High
0.3
0.3
0.3
0.3
0.3
3Ton
Low
0.3
0.3
0.3
0.3
0.3
10& 12SEER
High
0.3
0.3
0.3
0.3
0.3
3-1/2 Ton
Low
0.3
0.3
0.3
0.3
0.3
10& 12SEER
High
0.3
0.3
0.3
0.3
0.3
4Ton
Low
0.3
0.3
0.3
0.3
0.3
10& 12SEER
High
0.3
0.3
0.3
0.3
0.3
5 Ton
Low
0.3
0.3
0.3
0.3
0.3
10& 12SEER
High
0.3
0.3
0.3
0.3
0.3
Table 2. Maximum
0.3
0.3
0.3
High
0.5
0.5
Low
0.3
0.3
Medium
0.3
0.3
High
0.5
0.5
Low
0.3
0.3
Medium
0.3
0.3
High
0.5
0.5
PACKAGE
Blower Speed
SMALL
0.3
Medium
0.5
2 Ton
8kW 10kV_15kV_ 20kV_
PACKAGE
External
Static
Pressure
(ESP)
9kW 15kV_
Low
0.3
0.3 0.5
0.3
Slower Speed
3 Ton 10 SEER
Medium High
Medium
Unit
Unit Large Package A/C
3 Ton 10 & 12 SEER 1 Phase
4 Ton 10 & 12 SEER 1 Phase
5 Ton 10 & 12 SEER 1 Phase
3,4,&5Ton 10 SEER 208/230V
5 8 lO 15 5 8 lO 15 20 5 8 lO 15 20 9 15
Heater Kit Model
Heater Kit Part Number
H3HK005H-01B
917166B
H3HK008H-01B
917167B
H3HK010H-01B
917168B
H3HK015H-01B
917169B
H3HK005H-01B
917166B
H3HK008H-01B
917167B
H3HK010H-01B
917168B
H3HK015H-01B
917169B
H3HK020H-01B
917170B
H3HK005H-01B
917166B
H3HK008H-01B
917167B
H3HK010H-01B
917168B
H3HK015H-01B
917169B
H3HK020H-01B
917170B
H3HK009Q-01B
903854B
H3HK015Q-01B
903855B
Circuits 1 1 1 2 1 1 1 2 2 1 1 1 2 2 1 or2 1 or2
Breakers
Wiring Diagram Number
None
1
None
1
None
1
2
3
None
1
None
1
None
1
2
3
2
6
None
1
None
1
None
1
2
3
2
7
None or 2
8or9
None or 2
8or9
3 Phase
5 Ton
9
H3HK-009Q-01B
903854B
1
None
8
12 SEER
15
H3HK-015Q-01B
903855B
1
None
8
208/230V
3 Phase
3,4,&5Ton 10 SEER 460V
Large Package H/P
Nominal kW
9
H3HK-009S-01B
903850B
1 or2
None or2
10 orll
15
H3HK-015S-01B
903851B
1 or2
None or2
10 orll
3 Phase
2.5 & 3 Ton
5
H3HK005H-01B
917166B
1
None
1
10 & 12 SEER
8
H3HK008H-01B
917167B
1
None
2
1 Phase
10
H3HK010H-01B
917168B
2
2
2
15
H3HK015H-01B
917169B
2
2
4
3.5 & 4 Ton
5
H3HK005H-01B
917166B
2
2
2
10 & 12 SEER
8
H3HK008H-01B
917167B
2
2
2
1 Phase
10
H3HK010H-01B
917168B
2
2
2
15
H3HK015H-01B
917169B
3
3
5
2O
H3HK020H-01B
917170B
3
3
7
5 Ton
5
H3HK005H-01B
917166B
2
2
2
10 & 12 SEER
8
H3HK008H-01B
917167B
2
2
2
1 Phase
10
H3HK010H-01B
917168B
2
2
2
15
H3HK015H-01B
917169B
3
3
5
2O
H3HK-020H-01B
917170B
3
3
7
9
H3H K-009Q-01B
903854B
1 or2
None or 2
15
H3HK-015Q-01B
903855B
2
2
9
9 15
H3HK-009S-01B H3HK-015S-01B
903850B 903851B
1 or2 1 or 2
None or 2 None or 2
10or 11 10 or 11
2.5, 3, 3.5, 4, & 5 Ton 10 SEER 208/230V
3 Phase
3, 4,& 5Ton 10 SEER 460V
8or9
3 Phase
Table 3. Large Package
Applications
Heater Nominal
Small Package A/C
Wiring
Model
2,0 Ton 10 & 12 SEER
5 8 lO 5 8 lO 15 5 8 lO 15
H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK015H-01B H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK015H-01B
917166B 917167B 916768B 917166A 917167B 916768B 917169B 917166B 917167B 916768B 917169B
1 1 1 1 1 1 2 1 1 1 2
None None None None None None 2 None None None 2
1 1 1 1 1 1 3 1 1 1 3
5 8 lO 15 2o 5 8 lO 15 2o
H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK015H-01B H3HK020H-01 B H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK015H-01B H3HK020H-01 B
917166B 917167B 916768B 917169B 917170B 917166B 917167B 916768B 917169B 917170B
1 1 1 2 2 1 1 1 2 2
None None None 2 2 None None None 2 2
1 1 1 3 6 1 1 1 3 6
5 8 lO 15 2o 5 8 lO 5 8 lO 15 5 8 lO 15 5 8 lO 15 2o
H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK015H-01B H3HK020H-01 B H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK015H-01B H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK015H-01B H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK015H-01B H3HK020H-01 B
917166B 917167B 916768B 917169B 917170B 917166B 917167B 916768B 917166B 917167B 916768B 917169B 917166B 917167B 916768B 917169B 917166B 917167B 916768B 917169B 917170B
1 1 1 2 2 1 1 2 1 1 2 2or3 1 1 2 2or3 1 2 2 2or3 3
None None None 2 2 None None 2 None None 2 2or3 None None 2 2or3 None 2 2 2or3 3
1 1 1 3 6 1 1 2 1 1 2 4 1 2 2 4or5 1 2 2 4or5 7
5 8 lO 15 2o 5 8 lO 15 2o
H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK015H-01B H3HK020H-01 B H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK015H-01B H3HK020H-01 B
917166B 917167B 916768B 917169B 917170B 917166B 917167B 916768B 917169B 917170B
2 2 2 2or3 3 2 2 2 2or3 3
2 2 2 2or3 3 2 2 2 2or3 3
1 or2 2 2 4or5 7 2 2 2 4or5 7
1 phase 2.5 Ton 10 & 12 SEER 1 phase
3.5 Ton 10 & 12 SEER 1 phase
4.0 Ton 10 & 12 SEER 1 phase
5.0 Ton 10 & 12 SEER 1 phase
2.0 Ton 10 & 12 SEER 1 phase 2.5 Ton 10 & 12 SEER 1 phase
3.0 Ton 10 & 12 SEER 1 phase 3.5 Ton 10 & 12 SEER 1 phase
4.0 Ton 10 & 12 SEER 1 phase
5.0 Ton 10 & 12 SEER 1 phase
Number
Table 4. Small Package
Ci rcu its
Diagram Number
kW
1 phase
Package HIP
Kit
PaN
Unit
3.0 Ton 10 & 12 SEER
Small
Heater Kit
Applications
Breakers
Multiple Circuit Single Heatel
I
circuit
Circuit A
Copper Wire Size
I
Circuit B
Copper Wire Size
MOPi60oc175ocI90oc MOA MOPi6ooc 175°CI 90°C
Model
kw
MOA
Q4SA-036K
0
21.0
35
10
10
10
5
46.0
50
6
8
8
8
60.6
70
4
6
6
19.7
30
12
12
10
71.0
80
3
4
6
19.7
30
12
12
15
96.0
100
1
3
3
44.7
50
6
0
31.6
50
8
8
8
,5
56.6
70
4
6
6
28.5
50
71.1
80
3
4
6
28.5
50
10
81.6
90
3
4
4
28.5
15
106.6
110
1
2
3
20
131.6
150
00
0
1
0
38.4
60
8
8
8
5
63.4
80
4
6
8
77.9
90
3
4
10
88.4
100
2
15
113.4
125
20
138.4
0
Q4SA-048K
Q4SA-036C
Q4SA-048C
Q4SA-O36D
Q4SA-O48D
Q4SA-O6OD
12
40.9
45
6
8
8
12
51.3
60
6
6
8
8
8
51.3
60
6
6
8
10
10
10
28.1
30
10
10
10
10
10
10
42.7
45
6
8
8
50
10
10
10
53.1
60
6
6
8
28.5
50
10
10
10
53.1
60
6
6
28.5
50
10
10
10
53.1
60
6
6
6
35.3
60
8
8
8
28.1
30
10
10
10
4
35.3
60
8
8
8
42.7
45
6
8
8
3
4
35.3
60
8
8
8
53.1
60
6
6
8
0
2
2
35.3
60
8
8
8
53.1
60
6
6
150
00
0
1
35.3
60
8
8
8
53.1
60
6
6
15.3
25
12
12
12
9
42.3
45
6
8
8
14.0
20
14
14
14
28.4
30
10
10
10
15
60.4
70
4
6
6
14.0
20
14
14
14
46.5
50
6
8
8
18.5
30
12
12
12
Q4SC-048K
75
90°0
Copper Wire Size MOP
8
25.0
30
10
10
10
8
50.0
60
6
8
8
8
25
30
10
10
10
8
50
60
6
8
8
45.6
50
6
8
8
17.2
30
12
12
12
30.2
35
8
8
8
65.5
70
4
4
6
17.2
30
12
12
12
48.3
50
6
8
8
O
30.5
50
8
8
8
9
57.6
70
4
6
6
27.4
45
10
10
10
30.2
35
8
8
8
15
75.6
80
3
4
4
27.4
45
10
10
10
48.3
50
6
8
8
O
6.7
15
14
14
14
9
20.8
25
10
10
10
6
15
14
14
14
14.9
15
14
14
14
15
30.3
35
8
8
8
6
15
14
14
14
24.3
25
10
10
10
O
10.3
15
14
14
14
9
24.4
25
10
10
10
8.6
15
14
14
14
15.8
20
12
12
12
15
33.8
35
8
8
8
8.6
15
14
14
14
25.2
30
10
10
10
13.3
20
14
14
14
60
el el
MCA
9
75
900
9
27.4
30
10
10
10
11.6
20
14
14
14
15.9
20
12
12
12
15
36.8
40
8
8
8
11.6
20
14
14
14
25.2
30
10
10
10
O
22.5
35
10
10
10
5
47.5
50
6
8
8
8
62.1
70
4
6
6
21.2
35
10
10
10
40.9
45
6
8
8
10
72.5
80
3
4
6
21.2
35
10
10
10
51.3
60
6
6
8
15
97.5
100
1
3
3
46.2
50
6
8
8
51.3
60
6
6
8
O
31.1
50
8
8
8
,5
56.1
70
4
6
6
28
45
10
10
10
28.1
30
10
10
10
70.6
80
3
4
6
28
45
10
10
10
42.7
45
6
8
8
10
81.1
90
3
4
4
28
45
10
10
10
53.1
60
6
6
8
15
106.1
110
1
2
3
28
45
10
10
10
53.1
60
6
6
8
25
30
10
10
10
20
131.1
150
00
0
1
28
45
10
10
10
53.1
60
6
6
8
50
60
6
8
8
0
40.6
60
6
8
8
5
65.6
80
4
4
6
37.5
60
8
8
8
28.1
30
10
10
10
8
80.2
100
3
4
4
37.5
60
8
8
8
42.7
45
6
8
8
10
90.6
100
2
3
4
37.5
60
8
8
8
53.1
60
6
6
8
15
115.6
125
0
1
2
37.5
60
8
8
8
53.1
60
6
6
8
25
30
10
10
10
20
140.6
150
00
0
1
37.5
60
8
8
8
53.1
60
6
6
8
50
60
6
8
8
8
Q4SC-060K
60
15
0
Q4SC-O36K
el el
MOP
0
Q4SA-O6OC
Copper Wire Size MCA
8
Q4SA-060K
Circuit C
Table 5. Large Package HP Electrical
Data
Multiple Circuit Single
circuit
Circuit A
Circuit B
Circuit C
I 6c°ppe WiMOA eSize I6c°ppe Wi eSize I 6c° erWi eSizeI erWireSiz° Mode,.e kwtor MOA MOP 0o0175o0 I9OO0 MOP 0o0175o0 I9OO0 MOP 0o0175o01 9OO0 MOP 6c° OO0 I75o01 9OO0 P4SA-036K
P4SA-048K
P4SA-06OK
P4SA-036C
P4SA-048C
P4SA-060C
P4SA-036D
P4SA-048D
P4SA-060D
P4SC-036K
P4SC-048K
P4SC-060K
P4SC-060C
0
21.0
35
10
10
10
5
26.6
35
10
10
10
8
41.2
45
6
8
8
10
51.6
60
6
6
8
15
76.6
80
3
4
4
0
31.6
50
8
8
8
5
31.6
50
8
8
8
8
43.5
50
6
8
8
10
53.9
60
6
6
8
15
78.9
80
3
4
20
103.9
110
1
2
0
38.4
60
8
8
8
5
38.4
60
8
8
8
8
43.5
60
6
8
8
10
53.9
60
6
6
8
15
78.9
80
3
4
20
103.9
110
1
2
0
15.3
25
12
12
12
50.0
60
6
8
8
26.6
30
10
10
10
4
50.0
50
6
8
8
28.6
30
10
10
10
3
50.0
50
6
8
8
53.9
60
6
6
8
4
50
60
6
8
8
28.6
30
10
10
10
3
35.3
60
8
8
8
53.9
60
6
6
8
9
28.7
30
10
10
10
14.0
20
14
14
14
28.7
30
10
10
10
15
46.8
50
6
8
8
14.0
20
14
14
14
46.8
50
6
8
8
0
18.5
30
12
12
12
9
28.7
30
10
10
10
17.2
30
12
12
12
31
35
8
8
8
15
49
50
6
8
8
17.2
30
12
12
12
49
50
6
8
8
0
30.5
50
8
8
8
9
31
50
8
8
8
27.4
45
10
10
10
31
35
8
8
8
15
49
50
6
8
8
27.4
45
10
10
10
49
50
6
8
8
0
6.7
15
14
14
14
9
15
20
14
14
14
6
15
14
14
14
15
20
14
14
14
15
24.5
25
10
10
10
6
15
14
14
14
24.4
25
10
10
10
0
10.3
15
14
14
14
9
16.2
20
12
12
12
8.6
15
14
14
14
16.2
20
12
12
12
15
25.7
30
10
10
10
8.6
15
14
14
14
25.7
30
10
10
10
0
13.3
20
14
14
14
9
16.2
20
12
12
12
11.6
20
14
14
14
16.2
20
12
12
12
15
25.7
30
10
10
10
11.6
20
14
14
14
25.7
30
10
10
10
0
22.5
35
10
10
10
5
26.6
35
10
10
10
8
41.2
45
6
8
8
10
51.6
60
6
6
8
15
76.6
80
3
4
4
50.0
60
6
8
8
26.6
30
10
10
10
0
31.1
50
8
8
8
5
31.1
50
8
8
8
8
43.5
50
6
8
8
10
53.9
60
6
6
8
15
78.9
80
3
4
4
50
60
6
8
8
28.9
30
10
10
10
20
103.9
110
1
2
3
50
60
6
8
8
53.9
60
6
6
8
0
40.6
60
6
8
8
5
40.6
60
6
8
8
8
43.5
60
6
8
8
10
53.9
60
6
6
8
15
78.9
80
3
4
4
50
60
6
8
8
28.6
30
10
10
10
20
103.9
110
1
2
3
37.5
60
8
8
8
53.9
60
6
6
8
0
28.4
45
10
10
10
9
31
45
8
8
8
25.3
40
10
10
10
31
35
8
8
8
15
49
50
6
8
8
25.3
40
10
10
10
49
50
6
8
8
Table 6. Large Package
AC Electrical
Data
50
60
6
8
8
50
60
6
8
8
Heater Model
kw
MOA
Q3RA-024K
0
14.9
20
14
14
14
5
39.9
40
8
8
8
8
54.4
60
6
6
8
10
64.9
70
4
6
6
0
20.4
30
10
10
10
5
45.4
50
6
8
8
8
60.0
60
4
6
6
10
70.4
80
3
4
15
95.4
100
1
3
Q3RA-03OK
MOP I 60°0 I 75°0 I 90°0
0
21.8
5 8
CopperWireSize MOP I 60°0 I 75°0 I 90°0
Copse, 75°C Wit iSize MOP I 60°C 90°C
14
14
14
51.4
60
6
6
8
6
18.3
30
12
12
12
52.1
60
6
6
8
3
43.3
50
6
8
8
52.1
60
6
6
8
18.3
30
12
12
12
27.1
30
10
10
10
8
35
10
10
10
46.8
50
6
8
8
61.4
60
4
6
6
10
71.8
80
3
4
6
19.7
30
12
12
12
52.1
60
6
6
15
96.8
100
1
3
3
44.7
50
6
8
8
52.1
60
6
6
8
19.7
30
12
12
12
27.1
30
10
10
10
0
25.8
40
10
5
50.8
60
8
65.4
70
10
75.8
15
100.8
MOA
CopperWireSize MOP I 60°0 I 75°0 I 90°0
52.1
60
6
6
8
50
60
6
8
8
10
10
6
6
8
4
4
6
23.7
40
10
10
10
41.7
45
6
8
8
80
3
4
4
23.7
40
10
10
10
52.1
60
6
6
8
110
1
2
3
48.7
60
6
8
8
52.1
60
6
6
8
23.7
40
10
10
10
30.2
35
8
8
8
50
60
6
8
8
23.7
40
10
10
10
52.1
60
6
6
8
50
60
6
8
8
15 (3 circuit) 125.8
150
0O
1
2
0
31.6
50
8
8
8
5
56.6
70
4
6
6
28.6
50
10
10
10
29.3
30
10
10
10
8
71.1
80
3
4
6
28.6
50
10
10
10
43.9
45
6
8
8
10
81.6
90
3
4
4
28.6
50
10
10
10
54.3
60
6
6
8
15 (3 circuit)
106.6
110
1
2
3
28.6
50
10
10
10
28
30
10
10
10
50
60
6
8
8
20 (3 circuii
131.6
150
00
0
1
28.6
50
10
10
10
53
60
6
6
8
50
60
6
8
8
0
38.1
60
8
8
8
5
63.1
80
4
6
6
35.1
60
8
8
8
29.3
30
10
10
10
8
77.6
90
3
4
4
35.1
60
8
8
8
43.9
45
6
8
8
10
88.1
100
2
3
4
35.1
60
8
8
8
54.3
60
6
6
8
15 (3 circuit)
113.1
125
0
2
2
35.1
60
8
8
8
28
30
10
10
10
50
60
6
8
8
20 (3 circuit)
138.1
150
0
0
1
35.1
60
8
8
8
53
60
6
6
8
50
60
6
8
8
0
15.4
25
12
12
12
5
40.4
45
6
8
8
8
54.9
60
6
6
8
10
65.4
70
4
4
6
14
20
14
14
14
51.1
60
6
6
8
0
20.1
30
10
10
10
5
45.1
50
6
8
8
8
59.6
60
4
6
6
10
70.1
80
3
4
6
18
30
12
12
12
52.1
60
6
6
8
15
95.1
100
1
3
3
43
50
6
8
8
52.1
60
6
6
8
18
30
12
12
12
27.1
30
10
10
10
50
60
6
8
8
50
60
6
8
8
20 (3 circuit) Q3RA-048K
Q3RA-060K
Q3RC-024K
Q3RC-030K
15 (3 circuit) Q3RC-036K
0
21.8
35
10
10
10
5
46.8
50
6
8
8
8
61.4
70
4
6
6
19.7
30
12
12
12
41.7
45
6
8
8
10
71.8
80
3
4
6
19.7
30
12
12
12
52.1
60
6
6
8
15
96.8
100
1
3
3
44.7
50
6
8
8
52.1
60
6
6
8
19.7
30
12
12
12
27.1
30
10
10
10
15 (3 circuil Q3RC-042K
0
22.7
35
10
10
10
5
47.7
50
6
8
8
8
62.2
70
4
6
6
20.6
35
10
10
10
41.7
45
6
8
8
10
72.7
80
3
4
6
20.6
35
10
10
10
52.1
60
6
6
8
15
97.7
100
1
3
3
45.6
50
6
8
8
52.1
60
6
6
8
20.6
35
10
10
10
30.2
35
8
8
8
50
60
6
8
8
20.6
35
10
10
10
52.1
60
6
6
8
50
60
6
8
8
15 (3 circuit) 122.7
125
O
1
2
28.3
45
10
10
10
5
53.3
60
6
6
8
8
67.9
70
4
4
6
25.3
40
10
10
10
42.6
45
6
8
8
80
3
4
4
25.3
40
10
10
10
53
60
6
6
8
110
1
2
3
50.3
60
6
6
8
53
60
6
6
8
25.3
40
10
10
10
28
30
10
10
10
50
60
6
8
8
25.3
40
10
10
10
53
60
6
6
8
50
60
6
8
8
20 (3 circuii Q3RC-048K
0
10 15
78.3
103.3
15 (3 circuit) 20 (3 circuii
128.3
150
0
1
2
Table 7. Small 10
MCA
20
15 (3 circuit) Q3RA-042K
MOA
Cilcuit C
13.5
15 (3 circuit) Q3RA-036K
Multiple Circuil Circuit B
Circuit A
Single circuit Copper Wire Size
Package
HP Electrical
Data
Multiple
Model P3RA-024K
P3RA-030K
P3RA-036K
P3RA-042K
P3RA-048K
P3RA-060K
P3RC-024K
P3RC-030K
P3RC-036K
P3RC-042K
P3RC-048K
Circuit
Circuit A
Single circuit Heater kw 0
MCA 14.9
5
26.8
30
10
10
10
8
41.3
45
6
8
8
10
51.8
60
6
6
8
0
20.4
30
10
10
10
5
27.6
30
10
10
10
8
42.2
45
6
8
8
10
52.6
60
3
4
4
15
77.6
80
3
4
4
0
21.8
35
10
10
10
5
27.6
35
10
10
10
8
42.2
45
6
8
8
10
52.6
60
6
6
8
15
77.6
80
3
4
4
0
25.8
40
10
10
10
5
27.6
40
10
10
10
8
42.2
45
6
8
8
10
52.6
60
6
6
8
15
77.6
80
3
4
20
102.6
110
1
0
31.6
50
5
31.6
8
43.3
10
cepperwire MOP I 60°CI 75°CI 20 14 14
size 90°C 14
MCA
Circuit
copper wire size MOP I 60°CI75°CI90°C
B
I 60°cl copper7Wire Size MCAMOP 5°Cl g0°C
50
60
6
8
8
27.6
30
10
10
10
50
60
6
8
8
27.6
30
10
10
10
4
50.0
60
6
8
8
27.6
30
10
10
10
2
3
50.0
60
6
8
8
52.6
60
6
6
8
8
8
8
50
8
8
8
50
6
8
8
53.8
60
6
6
8
15
78.8
80
3
4
4
53.8
60
6
6
8
28.8
30
10
10
10
20
103.8
110
1
2
3
53.8
60
6
6
8
53.8
60
6
6
8
0
38.1
60
8
8
8
5
38.1
60
8
8
8
8
43.3
60
6
8
8
10
53.8
60
6
6
8
15
78.8
80
3
4
4
53.8
60
6
6
8
20
103.8
110
1
2
3
53.8
60
6
6
8
28.8 53.8
30 60
10 6
10 6
10 8
0
15.4
25
12
12
12
5
26.8
30
10
10
10
8
41.3
45
6
8
8
10
51.8
60
6
6
8
0
20.1
30
12
12
12
5
27.6
30
10
10
10
8
42.2
45
6
8
8
10
52.6
60
6
6
8
15
77.6
80
3
4
4
50
60
6
8
8
27.6
30
10
10
10
0
21.7
35
10
10
10
5
27.6
35
10
10
10
8
42.2
45
6
8
8
10
52.6
60
6
6
8
15
77.6
80
3
4
4
50
60
6
8
8
27.6
30
10
10
10
0
22.7
35
10
10
10
5
27.6
35
10
10
10
8
42.2
45
6
8
8
10
52.6
60
6
6
8
15
77.6
80
3
4
4
50
60
6
8
8
27.6
30
10
10
10
20
102.6
110
1
2
3
50
60
6
8
8
52.6
60
6
6
8
0
28.3
45
10
10
10
5
28.3
45
10
10
10
8
43.3
45
6
8
8
10
53.8
60
6
6
8
15
78.8
80
3
4
4
50
60
6
8
8
28.8
30
10
10
10
20
103.8
110
1
2
3
50
60
6
8
8
53.8
60
6
6
8
Table 8. Small
Package
AC Electrical
Data 11
WD#1 1 PHASE 5 KW, 8 KW, OR 10 KW, 1 CIRCUIT
APPLICATIONS INCLUDE: SMALL PACKAGE: Q3RA/C -024K(S&8 _) Q3RA/C -030K(S&8 _) Q3RA/C - 036K (5 kw) Q3RA/C - 042K (5 kw) P3RA/C - 024K (5, 8, & 10 P3RA/C - 030K (5, 8, & 10 P3RA/C - 042K (5, 8, & 10 P3RA/C - 048K (5, 8, & 10 P3RA/C - 060K (5, 8, & 10
(8 kw and 10 kw shown)
LARGE Q4SA/C P4SA/C P4SA/C P4SA/C
PACKAGE: - 036K (5 - 036K (5, - 048K (5, - 060K (5,
kw) 8, & 10 kw) 8, & 10 kw) 8, & 10 kw)
kw) kw) kw) kw) kw)
m
WHITE
2
_
BLACK
3 41
--BROWN--
5
_BLUE_ _ORANGE_
7
--GRAY
i -
--
8 9 i
BLACK --
\
FIELD
BLACK --
HEATER
WIRING
KIT PLUG
H
c°gP S[°2 ,,
mmmmmnmmm|
FACTORY LOW VOLTAGE HIGH
III
WIRING
VOLTAGE
[]
[]
$)-
C,RCU,T
BREAKER
J J
CIRCUIT A
12
WD #2 I PHASE 5 KW, 8 KW, OR 10 KW, 2 CIRCUIT
(8 kw and 10 kw shown)
APPLiCATiONS iNCLUDE: SMALL PACKAGE: Q3RA/C Q3RNC Q3RNC Q3RNC Q3RA Q3RC Q3RA -
LARGE
- 020K (10 kw) - 030K (10 kw) - 036K (8 & 10 kw) - 042K (8 & 10 kw) 048K (5, 8, & 10 kw) 048K (8 & 10 kw) 060K (5, 8, & 10 kw)
PACKAGE:
Q4SA/C - 036K (8 & 10 kw) Q4SA/C - 048K (5, 8, & 10 kw) Q4SA/C - 060K (5, 8, & 10 kw)
WHITE
K
BLUE_ __
_ORANGE
_ R
GRAY
=
--GRAY-- --
_
HEA_ER
K(T PLUG
COMPRESSOR CONTACTOR
°lMl° k _L2 m
TERMINAL BLOCK (NOT NECESSARY FOR10SEER HP)
LI m
m
FIELD
WIRING
mmmmmmmmmm
FACTORY LOW VOLTAGE HiGH
VOLTAG_
WIRING
m []
[]
[] []
CIRCUIT A [] []
m []
CIRCUIT B
13
W_ i PHASE 15 KW, 2 CiRCUiT
APPLiCATiONS iNCLUDE: LARGE PACKAGE: P4SNC - 036K P4SA/C - 048K P4SNC - 060K
(Air Conditioning
SMALL P3RA/C P3RA/C P3RA/C P3RA/C
Application)
PACKAGE: - 030K - 036K - 042K - 048K
CONTACTOR RED_ RED_ ELEMENTS
CONTACTOR ELEMENTS
GRAY_
L
BLACK BLACK
HEATER KiT PLUG
FIELD WIRING
BLACK
mmmmmmmmm|
FACTORY LOW VOLTAGE
W_RING []
[]
HIGH VOLTAGE
BREAKER
m m
m m
CIRCUIT A
14
WD#4 I PHASE 15 KW, 2 CiRCUiT
(Heat
Pump
APPLiCATiONS iNCLUDE: LARGE PACKAGE: SMALL Q4SA - 036K Q3RA/C Q4SC - 036K Q3RA/C Q3RA/C Q3RC -
Application)
PACKAGE: - 030K - 036K - 042K 048K
ELEMENTS
ELEMENTS
] BLACK BLACK
L
HEATER BLACK_
KIT PLUG
COMPRESSOR CONTACTOR
T2
IT1
_L2 FIELD
WIRING
Im Im m FACTORY
LOW HiGH
VOLTAGE VOLTAGE
m m
WIRING
Im Im Im m
L1
II
! m
TERMINAL
[]
[]
BREAKER
CIRCUIT )__ [] []
CIRCUNT
__
[]
[] []
BLOCK
[] []
[] []
A
CIRCUIT
B
15
WD#5 I PHASE 15 KW, 3 CIRCUIT
APPLiCATiONS iNCLUDE: SMALL PACKAGE: Q3RA/C - 042K Q3RA/C - 048K Q3RA - 060K
LARGE Q4SA/C Q4SA/C P4SA/C
PACKAGE: - 048K - 060K - 060K
CONTACTOR
ELEMENTS
BLACK
= ELEMENTS
GRAYq BLACK BLACK
BLACK
COMPRESSOR CONTACTOR
FIELD
WIR$NG Im m _m_mlm FACTORY WIRING
[] [] [] [] [] []
m u=|
LOW VOLTAGE HIGH
VOLTAGE
[] []
[] [] [] [] [] []
[] []
CIRCUIT A
16
[]
[] []
[] m
C)RCUIT C
[] []
[]
[] []
CIRCUIT B
WD#6 1 PHASE 20 KW, 2 CIRCUIT
APPLICATIONS iNCLUDE: SMALL PACKAGE: P3RNC - 042K P3RNC - 048K P3RA/C - 060K
LARGE PACKAGE: P4SA/C - 048K
I I I I I
ELEMENTS
ELEMENTS
,BLACK,
HEATER
KIT PLUG
=BLACKI 'BLACK
COMPRESSOR CONTACTOR
m
[]
CIRCUIT BREAKER
[] []
[] [] CIRCUIT
B
[] []
[] [] CIRCUmT
A
17
WD#7 1 PHASE 20 KW, 3 CIRCUIT
APPLICATIONS INCLUDE: SMALL PACKAGE: Q3RA/C - 042K Q3RA/C - 048K Q3RA - 060K
LARGE PACKAGE: Q4SA/C - 048K Q4SA/C - 060K P4SA/C - 060K
3 ELEMENTS
4
8
ELEMENTS
BLACK BLACK BLACK
KIT PLUG
BLACK
COMPRESSOR CONTACTOR
TM
FfELD WfRING
Im Im Im Im Iwl Im Im Im m |
FACTORY LOW VOLTAGE H_GH VOLTAGE
W_RING
I 1
[] 1
TERMINAL []
_i_
18
[] []
[] []
ClRCUIT
A
BREAKER
[] []
[] [] CIRCUIT
[]
C
[] []
m []
ClRCUNT B
BLOCK
WD#8 3 PHASE, 208/230V 9 OR 15 KW, I CiRCUiT APPLiCATiONS P4SA P4SA P4SA P4SC Q4SA Q4SA
-
036C 048C 060C 060C 036C 048C
iNCLUDE: (9 & 15 (9 & 15 (9 & 15 (9 & 15 (9 kw) (9 kw)
kw) kw) kw) kw)
COMPRESSOR
FACTORY WIRING LOW VO LTA%EFIELD WIRING mmmllmllmm HIGH VOLTAGE
CONTACTOR
1 =
TERMINAL BLOCK
ELEMENT
ELEMENT
ELEMENT
HEATER
KIT PLUG
19
WD#9 3 PHASE, 208/230V 9 OR 15 KW, 2 CIRCUIT APPLICATIONS
INCLUDE:
Q4SA - 036C (15 kw) Q4SA - 048C (15 kw) Q4SA - 060C (9 & 15 kw)
CIRCUIT
A
I | |
l
i_
FIELD
CIRCUIT BREAKER
L11(_I
COMPRESSORcoNTACTO R
WIRING
mlimll
FACTORY LOW VOLTAGE HIGH
ELEMENT
I==== ORANGE
2O
VOLTAGE
m ! m mla m = WIRING
WD#10 3 PHASE, 460V 9 OR 15 KW, 1 CiRCUiT APPLiCATiONS Q4SA - 036D (9 Q4SA - 048D (9 Q4SA - 060D (9 P4SA - 036D (9 P4SA - 048D (9 P4SA - 060D (9
iNCLUDE: & 15 kw) & 15 kw) & 15 kw) & 15 kw) & 15 kw) & 15 kw)
H
H
H
"L3_tL2 _t' _
TT,T_,TI
COMPRESSOR CONTACTOR
FIELD
WIRING
==m==m==
FACTORY LOW
VOLTAGE
HIGH
VOLTAGE
WIRING
YELLOW
RED --
ELEMENT
__
2:
ELEMENT
ELEMENT _°ROW iHEATER KIT PLUG
21
WD#11 3 PHASE, 460V 9 OR 15 KW, 2 CIRCUIT APPLICATIONS Q4SA - 036D (9 Q4SA - 048D (9 Q4SA - 060D (9 P4SA - 036D (9 P4SA - 048D (9 P4SA - 060D (9
INCLUDE: & 15 kw) & 15 kw) & 15 kw) & 15 kw) & 15 kw) & 15 kw)
CIRCUIT | | | | |
CIRCUIT
B
ClRCUtT
A
I I I I I
BREAKER
!J
CtRCUIT
BREAKER
BLACK
---(?L3
=_2
11(_L
COMPRESSO
_T3
_T2
"_TI"_
R
_YELLOW_
I
CONTACTOR
_RED_
FIELD
WIRING
mmmmmmmm
FACTORY LOW
VOLTAGE
HIGH
VOLTAGE
WIRING
LIMIT
1
ELEMENT
0 ELEMENT O
=ORANGE
ELEMENT
CI_NIT
HEATER
22
KIT PLUG
BROW i -
23
INSTALLER PLEASE LEAVE THESE iNSTALLATiON iNSTRUCTiONS WITH THE UNiT OWNER.
III lllllllrllllllllllllll II!
7083400 Specifications and illustrations subject to change without notice and without incurring obligations. Printed inU.S.A. (02/04)
Package Electric Heater Kits Description Installation Conditioners
of 208/240V
and 460V
and Packaged
H3HK
Heater
Kits in Packaged
Air
Heat Pumps.
These instructions are primarily intended to assist qualified individuals experienced in the proper installation of heating and/or air conditioning appliances. Some local codes require licensed installation/service personnel for this type equipment. All installations must be in accordance with these instructions and with all applicable national and local codes and standards. Read these instructions thoroughly before starting the installation. warnings contained within these instructions and on the unit.
GENERAL
INFORMATION
The H3HK Heater Kits are approved for use in the Packaged Air Conditioners and Packaged Heat Pumps when applied and installed according to these instructions. See Table 3 or Table 4 for the approved H3HK air conditioner
Follow all precautions
and
combinations and the approved H3HK heat pump combinations. Refer to the National Electric Code (ANSI/NFPA 70) or in Canada the Canadian Electric Code Part 1 (CSA C.22.1) and applicable local codes for overcurrent protection and disconnect requirements.
ELECTRICAL
SUPPLY
Circuit Options -- The units with electric heat may be wired for single or multiple circuits and may have circuit breakers or terminal blocks.
WARNING: To
avoid
the
risk
of
electric
shock, personal injury, or death, disconnect all electrical power to the unit before performing any maintenance or service. The unit may have more than one
power
supply.
if the unit was previously installed without electric heat, the existing supply wiring may not be sufficient to handle the increased load. See the unit rating label or Tables 5 thru 8 for minimum circuit ampacities and maximum overcurrent protection ratings. The units with installed electric heat may be supplied by a single circuit or by multiple circuits. Additional accessory kits may be required if single circuit installation and/or circuit breakers are desired. See Table 1 for accessory descriptions and part numbers.
Installation Remove the control box access panel. Locate the 9 pin (12 pin for 3 phase kits) heater plug assembly and remove the jumper cap. Discard the jumper cap; it will not be used after installing the heater kits. Order Description
Number
208/240v 1 Phase Heater Kits H3HK005H-01A,
5kw, 1-Stage Heater Kit
917166B
H3HK008H-01A,
8kw, 1-Stage Heater Kit
917167B
H3HK010H-01A,
10kw, 1-Stage Heater Kit
917168B
H3HK015H-01A,
15kw, 1-Stage Heater Kit
917169B
H3HK015H-21A,
15kw, 1-Stage Heater Kit
917172B
H3HK020H-01A,
20kw, 1-Stage Heater Kit
917170B
H3HK020H-21A,
20kw, 1-Stage Heater Kit
917173B
Note: Circuit breakers installed in the unit are for short-circuit protection of the internal wiring and to serve as a unit disconnect. The circuit breakers DO NOT provide overcurrent protection of the supply wiring. Whether or not circuit breakers are used in the units, overcurrent protection must be provided at the branch circuit distribution panel and sized as shown in Tables 5 thru 8 or on the unit rating label and according to the National Electric Code, Canadian Electrical Code and applicable local codes, tn most cases the overcurrent protection specified on the unit rating label is less than the 60 amp rating of the circuit breakers used in the units. This is because the function of the overcurrent protection required at the distribution panel (field supplied) and the unit mounted breakers is different. When circuit breakers are used they must be used on all circuits. Refer to Table 3 or Table 4 for the correct number of circuit breakers to install. See Table 1 for the correct circuit breaker for the application. if the number of circuits as shown in Table 3 or Table 4 is more than one, circuit breakers are required, tf single circuit supply wiring is desired, use the 4-pole single circuit adapter kit (PIN 913350) when two 2-pole circuit breakers are used and the 6-pole single circuit adapter kit (PIN 913556) when three 2-pole circuit breakers are used. The single circuit adapter kits are not applicable to three phase units. if circuit breakers are not being used, proceed to the Terminal Block section. Circuit
208/240v 3 Phase Heater Kits H3HK-009Q-01A,
9kw, Heater Kit
903854B
H3HK-015Q-01A,
15kw, Heater Kit
903855B
Breakers -- If circuit breakers are used
for any circuit, they must be used for all circuits. Use one breaker for each circuit as shown in Table 3.
460v 3 Phase Heater Kits H3HK-009S-01A,
9kw, Heater Kit
903850B
H3HK-015S-01A,
15kw, Heater Kit
903851B
Breaker Attachment -- Install the circuit breaker mounting rail to the control panel with the 4 blunt tip screws provided.
Accessories: 4-Pole Single Circuit Adaptor*
913350
6-Pole Single Circuit Adaptor*
913556
Circuit Breaker, Single Phase (2-Pole)
913554
Circuit Breaker, Three Phase (3-Pole)
913740
*Single Phase Models Only
Table 1. Accessories 2
Attaching to BracketAttach the circuit breakers in the unit by hooking the bottom in the base of the circuit breaker onto the left rail of the bracket and rotating to the right. The circuit breaker should snap into place. Install the breakers so that the "ON" position is at the right.
SMALL
PACKAGE
RELAY /
ACCESS
HOLE
,,_CONTACTOR
BREAKERS"
I
ELECTRIC HEATING ELEMENTS
\
LIMIT SWmTCH
CONTACTOR
ol
LARGE
PACKAGE
TERMINAL BLOCKS (Se{ect ModeM) ACCESS HOLE
TERMINAL
CIRCUIT BREAKER BRACKET
CONTACTOR ELECTRIC HEATING ELEMENTS CIRCUIT BREAKERS
CONTACTORS
(Shown in position for downshot flow)
SINGLE CIRCUIT ADAPTER
Figure Breaker
Removal
--
1.
Location
Insert a screwdriver
into
the hole in the release tab and pull out while rotating the breaker out and to the left. The white release tab is located at the base of the breaker under the line side (right) terminals. Single Circuit Kit (single phase only) -- Refer to the instructions included with the single circuit adapter kit for details on how to configure the adapter. Install the adapter as shown in the instructions in the line side (right) of the breakers. Proceed to the Element Installation section. Terminal Blocks -- Approved H3HK heater kits are shipped with a terminal block for small package units. For large package units the terminal block(s) supplied with the kits will not be used. The electric heater kits will be wired to the existing factory installed terminal block, tf the number of circuits indicated in Table 3 or Table 4 is two or three, then the circuit breakers must be used; see the Circuit Breaker section.
of Major Components Element installation -- Remove the blower access panel. Remove the heater close-off plate(s) in the electric heat panel. When installing single banks of heaters, position them closest to the blower. Install the heater kit in the opening with the limit control towards the top of the unit if the unit is using the side supply and return duct openings. If the unit is using the downshot supply and return openings, install the heater kit in the opening with the limit towards the bottom of the unit. Make sure that the element support rod is inserted into the support bracket. Refer to Figure 2. Fasten the heater with the same screws used to secure the close-off plates. Staged Heat -- To stage the heat on the 15 kw or 20 kw Heater Kits the factory set wiring will need to be modified. The orange wire in Pin 2 on the Heat Accessory Plug will be re-routed. See the Typical AC (or HP) Thermostat Connection figure in the HP or AC Installation Instructions. 3
/ WARNING: Rooftop
applications
cal ducts must installed in the that the elements
over a supply
iMPORTANT: with verti=
have an elbow supply duct so are not directly
Torque the circuit breaker to 45 in=lbs, AIRFLOW
grille. The maximum external static pressure for the units are listed in Table 2.
WARNING: The heater will not function erly if the elements rectly installed. ELEMENT
lugs
are
prop-
not cor-
POWERWIRING
Route the main power leads (heavy black and red wires) and the 9 or 12-pin heat plug through the access hole at the top of the control panel to the circuit breaker or terminal block. Connect the 9 or 12-pin heat kit plug to the heat accessory plug located in the control box. Refer to the detailed wiring diagrams for connections. Make sure that the connections are secure. Select large package units have additional terminal blocks installed. The power leads from the heater kit should be attached to these terminal blocks. Wires needed to connect from terminal blocks to circuit breakers should be field supplied. The 6 inch leads are provided with the heater kit to connect the circuit breaker(s) to the compressor contactor. Mark the appropriate box on the unit rating plate with an "X" to indicate which heater kit has been installed. HEATING ELEMENTS
SUPPORT BRACKET
Y
(ESP)
The unit is factory shipped with a jumper wire between the heating speed contacts and the cooling speed contacts on the blower relay. If the heating/cooling speed desired is the preset speed, then no modifications are required. If a different heating/cooling speed is desired, remove the blower lead attached to terminal #4 on the relay (leave the jumper wire in place). Cut the wire tie retaining the unused motor speed taps and connect the desired motor tap to terminal #4 on the relay. Refer to Figure 3 for the motor lead color coding. For 460V units, refer to the wiring diagram on the blower motor to select a different blower speed. If a heating speed different from the cooling speed is desired, remove and discard the jumper wire from the blower relay. Cut the wire tie holding the unused speed taps. Connect the desired heating speed tap to pin #6 and the desired cooling speed tap on pin #4 of the blower relay, 208/230V units only. For 460V units only, one fan speed is obtainable for both heating and cooling. It is recommended that the fan be set for high speed operation when using electric auxiliary heat.
WARNING: After making any changes to the blower speed setting, be sure to bundle and insulate any unused speed taps so that they will not contact with cabinet or any uninsulated live parts, CLEARANCE
I% ¢_
®
Figure 2. Element
¢
®
Support
Bracket
All units are approved for zero clearance to combustibles when installed according to these instructions and other instructions included with the unit and other approved accessories.
208/230V
Units LARGE
1
PACKAGE
SMALL
PACKAGE
RED (LOW)
2 3
BLUE
4
BLACK
(MEDIUM)
BLACK
(HIGH)
- (HIGH)
DEFAULT
RED (LOW)
5 6 --
WHITE
(COMMON)
Figure 3. Blower
Motor Speed Tap Color Code
Three Phase
Single Phase Unit 2.5 & 3 Ton 10 & 12 SEER
3.5 & 4 Ton 10 & 12 SEER
5 Ton 10 & 12 SEER
Blower Speed
5kW
Low
0.3
8kW 10kV_ 15kW20kW 0.3
0.3
0.3
Medium
0.3
0.3
0.3
0.3
High
0.5
0.5
0.5
0.5
Low
0.3
0.3
0.3
0.3
0.3 0.5
0.3 0.5
0.3 0.5
0.3 0.5
Low
0.3
0.3
0.3
0.3
0.3
High
0.5
0.3 0.5
LARGE
Unit
0.3 0.5
0.3
4 Ton 10 SEER
5 Ton 10 SEER
0.3
0.5
5kW
Low
0.3
0.3
0.3
0.3
0.3
10& 12SEER
High
0.3
0.3
0.3
0.3
0.3
2-t/2 Ton
Low
0.3
0.3
0.3
0.3
0.3
10& 12SEER
High
0.3
0.3
0.3
0.3
0.3
3Ton
Low
0.3
0.3
0.3
0.3
0.3
10& 12SEER
High
0.3
0.3
0.3
0.3
0.3
3-1/2 Ton
Low
0.3
0.3
0.3
0.3
0.3
10& 12SEER
High
0.3
0.3
0.3
0.3
0.3
4Ton
Low
0.3
0.3
0.3
0.3
0.3
10& 12SEER
High
0.3
0.3
0.3
0.3
0.3
5 Ton
Low
0.3
0.3
0.3
0.3
0.3
10& 12SEER
High
0.3
0.3
0.3
0.3
0.3
Table 2. Maximum
0.3
0.3
0.3
High
0.5
0.5
Low
0.3
0.3
Medium
0.3
0.3
High
0.5
0.5
Low
0.3
0.3
Medium
0.3
0.3
High
0.5
0.5
PACKAGE
Blower Speed
SMALL
0.3
Medium
0.5
2 Ton
8kW 10kV_15kV_ 20kV_
PACKAGE
External
Static
Pressure
(ESP)
9kW 15kV_
Low
0.3
0.3 0.5
0.3
Slower Speed
3 Ton 10 SEER
Medium High
Medium
Unit
Unit Large Package A/C
3 Ton 10 & 12 SEER 1 Phase
4 Ton 10 & 12 SEER 1 Phase
5 Ton 10 & 12 SEER 1 Phase
3,4,&5Ton 10 SEER 208/230V
5 8 lO 15 5 8 lO 15 20 5 8 lO 15 20 9 15
Heater Kit Model
Heater Kit Part Number
H3HK005H-01B
917166B
H3HK008H-01B
917167B
H3HK010H-01B
917168B
H3HK015H-01B
917169B
H3HK005H-01B
917166B
H3HK008H-01B
917167B
H3HK010H-01B
917168B
H3HK015H-01B
917169B
H3HK020H-01B
917170B
H3HK005H-01B
917166B
H3HK008H-01B
917167B
H3HK010H-01B
917168B
H3HK015H-01B
917169B
H3HK020H-01B
917170B
H3HK009Q-01B
903854B
H3HK015Q-01B
903855B
Circuits 1 1 1 2 1 1 1 2 2 1 1 1 2 2 1 or2 1 or2
Breakers
Wiring Diagram Number
None
1
None
1
None
1
2
3
None
1
None
1
None
1
2
3
2
6
None
1
None
1
None
1
2
3
2
7
None or 2
8or9
None or 2
8or9
3 Phase
5 Ton
9
H3HK-009Q-01B
903854B
1
None
8
12 SEER
15
H3HK-015Q-01B
903855B
1
None
8
208/230V
3 Phase
3,4,&5Ton 10 SEER 460V
Large Package H/P
Nominal kW
9
H3HK-009S-01B
903850B
1 or2
None or2
10 orll
15
H3HK-015S-01B
903851B
1 or2
None or2
10 orll
3 Phase
2.5 & 3 Ton
5
H3HK005H-01B
917166B
1
None
1
10 & 12 SEER
8
H3HK008H-01B
917167B
1
None
2
1 Phase
10
H3HK010H-01B
917168B
2
2
2
15
H3HK015H-01B
917169B
2
2
4
3.5 & 4 Ton
5
H3HK005H-01B
917166B
2
2
2
10 & 12 SEER
8
H3HK008H-01B
917167B
2
2
2
1 Phase
10
H3HK010H-01B
917168B
2
2
2
15
H3HK015H-01B
917169B
3
3
5
2O
H3HK020H-01B
917170B
3
3
7
5 Ton
5
H3HK005H-01B
917166B
2
2
2
10 & 12 SEER
8
H3HK008H-01B
917167B
2
2
2
1 Phase
10
H3HK010H-01B
917168B
2
2
2
15
H3HK015H-01B
917169B
3
3
5
2O
H3HK-020H-01B
917170B
3
3
7
9
H3H K-009Q-01B
903854B
1 or2
None or 2
15
H3HK-015Q-01B
903855B
2
2
9
9 15
H3HK-009S-01B H3HK-015S-01B
903850B 903851B
1 or2 1 or 2
None or 2 None or 2
10or 11 10 or 11
2.5, 3, 3.5, 4, & 5 Ton 10 SEER 208/230V
3 Phase
3, 4,& 5Ton 10 SEER 460V
8or9
3 Phase
Table 3. Large Package
Applications
Heater Nominal
Small Package A/C
Wiring
Model
2,0 Ton 10 & 12 SEER
5 8 lO 5 8 lO 15 5 8 lO 15
H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK015H-01B H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK015H-01B
917166B 917167B 916768B 917166A 917167B 916768B 917169B 917166B 917167B 916768B 917169B
1 1 1 1 1 1 2 1 1 1 2
None None None None None None 2 None None None 2
1 1 1 1 1 1 3 1 1 1 3
5 8 lO 15 2o 5 8 lO 15 2o
H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK015H-01B H3HK020H-01 B H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK015H-01B H3HK020H-01 B
917166B 917167B 916768B 917169B 917170B 917166B 917167B 916768B 917169B 917170B
1 1 1 2 2 1 1 1 2 2
None None None 2 2 None None None 2 2
1 1 1 3 6 1 1 1 3 6
5 8 lO 15 2o 5 8 lO 5 8 lO 15 5 8 lO 15 5 8 lO 15 2o
H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK015H-01B H3HK020H-01 B H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK015H-01B H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK015H-01B H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK015H-01B H3HK020H-01 B
917166B 917167B 916768B 917169B 917170B 917166B 917167B 916768B 917166B 917167B 916768B 917169B 917166B 917167B 916768B 917169B 917166B 917167B 916768B 917169B 917170B
1 1 1 2 2 1 1 2 1 1 2 2or3 1 1 2 2or3 1 2 2 2or3 3
None None None 2 2 None None 2 None None 2 2or3 None None 2 2or3 None 2 2 2or3 3
1 1 1 3 6 1 1 2 1 1 2 4 1 2 2 4or5 1 2 2 4or5 7
5 8 lO 15 2o 5 8 lO 15 2o
H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK015H-01B H3HK020H-01 B H3HK005H-01 B H3HK008H-01B H3HK010H-01B H3HK015H-01B H3HK020H-01 B
917166B 917167B 916768B 917169B 917170B 917166B 917167B 916768B 917169B 917170B
2 2 2 2or3 3 2 2 2 2or3 3
2 2 2 2or3 3 2 2 2 2or3 3
1 or2 2 2 4or5 7 2 2 2 4or5 7
1 phase 2.5 Ton 10 & 12 SEER 1 phase
3.5 Ton 10 & 12 SEER 1 phase
4.0 Ton 10 & 12 SEER 1 phase
5.0 Ton 10 & 12 SEER 1 phase
2.0 Ton 10 & 12 SEER 1 phase 2.5 Ton 10 & 12 SEER 1 phase
3.0 Ton 10 & 12 SEER 1 phase 3.5 Ton 10 & 12 SEER 1 phase
4.0 Ton 10 & 12 SEER 1 phase
5.0 Ton 10 & 12 SEER 1 phase
Number
Table 4. Small Package
Ci rcu its
Diagram Number
kW
1 phase
Package HIP
Kit
PaN
Unit
3.0 Ton 10 & 12 SEER
Small
Heater Kit
Applications
Breakers
Multiple Circuit Single Heatel
I
circuit
Circuit A
Copper Wire Size
I
Circuit B
Copper Wire Size
MOPi60oc175ocI90oc MOA MOPi6ooc 175°CI 90°C
Model
kw
MOA
Q4SA-036K
0
21.0
35
10
10
10
5
46.0
50
6
8
8
8
60.6
70
4
6
6
19.7
30
12
12
10
71.0
80
3
4
6
19.7
30
12
12
15
96.0
100
1
3
3
44.7
50
6
0
31.6
50
8
8
8
,5
56.6
70
4
6
6
28.5
50
71.1
80
3
4
6
28.5
50
10
81.6
90
3
4
4
28.5
15
106.6
110
1
2
3
20
131.6
150
00
0
1
0
38.4
60
8
8
8
5
63.4
80
4
6
8
77.9
90
3
4
10
88.4
100
2
15
113.4
125
20
138.4
0
Q4SA-048K
Q4SA-036C
Q4SA-048C
Q4SA-O36D
Q4SA-O48D
Q4SA-O6OD
12
40.9
45
6
8
8
12
51.3
60
6
6
8
8
8
51.3
60
6
6
8
10
10
10
28.1
30
10
10
10
10
10
10
42.7
45
6
8
8
50
10
10
10
53.1
60
6
6
8
28.5
50
10
10
10
53.1
60
6
6
28.5
50
10
10
10
53.1
60
6
6
6
35.3
60
8
8
8
28.1
30
10
10
10
4
35.3
60
8
8
8
42.7
45
6
8
8
3
4
35.3
60
8
8
8
53.1
60
6
6
8
0
2
2
35.3
60
8
8
8
53.1
60
6
6
150
00
0
1
35.3
60
8
8
8
53.1
60
6
6
15.3
25
12
12
12
9
42.3
45
6
8
8
14.0
20
14
14
14
28.4
30
10
10
10
15
60.4
70
4
6
6
14.0
20
14
14
14
46.5
50
6
8
8
18.5
30
12
12
12
Q4SC-048K
75
90°0
Copper Wire Size MOP
8
25.0
30
10
10
10
8
50.0
60
6
8
8
8
25
30
10
10
10
8
50
60
6
8
8
45.6
50
6
8
8
17.2
30
12
12
12
30.2
35
8
8
8
65.5
70
4
4
6
17.2
30
12
12
12
48.3
50
6
8
8
O
30.5
50
8
8
8
9
57.6
70
4
6
6
27.4
45
10
10
10
30.2
35
8
8
8
15
75.6
80
3
4
4
27.4
45
10
10
10
48.3
50
6
8
8
O
6.7
15
14
14
14
9
20.8
25
10
10
10
6
15
14
14
14
14.9
15
14
14
14
15
30.3
35
8
8
8
6
15
14
14
14
24.3
25
10
10
10
O
10.3
15
14
14
14
9
24.4
25
10
10
10
8.6
15
14
14
14
15.8
20
12
12
12
15
33.8
35
8
8
8
8.6
15
14
14
14
25.2
30
10
10
10
13.3
20
14
14
14
60
el el
MCA
9
75
900
9
27.4
30
10
10
10
11.6
20
14
14
14
15.9
20
12
12
12
15
36.8
40
8
8
8
11.6
20
14
14
14
25.2
30
10
10
10
O
22.5
35
10
10
10
5
47.5
50
6
8
8
8
62.1
70
4
6
6
21.2
35
10
10
10
40.9
45
6
8
8
10
72.5
80
3
4
6
21.2
35
10
10
10
51.3
60
6
6
8
15
97.5
100
1
3
3
46.2
50
6
8
8
51.3
60
6
6
8
O
31.1
50
8
8
8
,5
56.1
70
4
6
6
28
45
10
10
10
28.1
30
10
10
10
70.6
80
3
4
6
28
45
10
10
10
42.7
45
6
8
8
10
81.1
90
3
4
4
28
45
10
10
10
53.1
60
6
6
8
15
106.1
110
1
2
3
28
45
10
10
10
53.1
60
6
6
8
25
30
10
10
10
20
131.1
150
00
0
1
28
45
10
10
10
53.1
60
6
6
8
50
60
6
8
8
0
40.6
60
6
8
8
5
65.6
80
4
4
6
37.5
60
8
8
8
28.1
30
10
10
10
8
80.2
100
3
4
4
37.5
60
8
8
8
42.7
45
6
8
8
10
90.6
100
2
3
4
37.5
60
8
8
8
53.1
60
6
6
8
15
115.6
125
0
1
2
37.5
60
8
8
8
53.1
60
6
6
8
25
30
10
10
10
20
140.6
150
00
0
1
37.5
60
8
8
8
53.1
60
6
6
8
50
60
6
8
8
8
Q4SC-060K
60
15
0
Q4SC-O36K
el el
MOP
0
Q4SA-O6OC
Copper Wire Size MCA
8
Q4SA-060K
Circuit C
Table 5. Large Package HP Electrical
Data
Multiple Circuit Single
circuit
Circuit A
Circuit B
Circuit C
I 6c°ppe WiMOA eSize I6c°ppe Wi eSize I 6c° erWi eSizeI erWireSiz° Mode,.e kwtor MOA MOP 0o0175o0 I9OO0 MOP 0o0175o0 I9OO0 MOP 0o0175o01 9OO0 MOP 6c° OO0 I75o01 9OO0 P4SA-036K
P4SA-048K
P4SA-06OK
P4SA-036C
P4SA-048C
P4SA-060C
P4SA-036D
P4SA-048D
P4SA-060D
P4SC-036K
P4SC-048K
P4SC-060K
P4SC-060C
0
21.0
35
10
10
10
5
26.6
35
10
10
10
8
41.2
45
6
8
8
10
51.6
60
6
6
8
15
76.6
80
3
4
4
0
31.6
50
8
8
8
5
31.6
50
8
8
8
8
43.5
50
6
8
8
10
53.9
60
6
6
8
15
78.9
80
3
4
20
103.9
110
1
2
0
38.4
60
8
8
8
5
38.4
60
8
8
8
8
43.5
60
6
8
8
10
53.9
60
6
6
8
15
78.9
80
3
4
20
103.9
110
1
2
0
15.3
25
12
12
12
50.0
60
6
8
8
26.6
30
10
10
10
4
50.0
50
6
8
8
28.6
30
10
10
10
3
50.0
50
6
8
8
53.9
60
6
6
8
4
50
60
6
8
8
28.6
30
10
10
10
3
35.3
60
8
8
8
53.9
60
6
6
8
9
28.7
30
10
10
10
14.0
20
14
14
14
28.7
30
10
10
10
15
46.8
50
6
8
8
14.0
20
14
14
14
46.8
50
6
8
8
0
18.5
30
12
12
12
9
28.7
30
10
10
10
17.2
30
12
12
12
31
35
8
8
8
15
49
50
6
8
8
17.2
30
12
12
12
49
50
6
8
8
0
30.5
50
8
8
8
9
31
50
8
8
8
27.4
45
10
10
10
31
35
8
8
8
15
49
50
6
8
8
27.4
45
10
10
10
49
50
6
8
8
0
6.7
15
14
14
14
9
15
20
14
14
14
6
15
14
14
14
15
20
14
14
14
15
24.5
25
10
10
10
6
15
14
14
14
24.4
25
10
10
10
0
10.3
15
14
14
14
9
16.2
20
12
12
12
8.6
15
14
14
14
16.2
20
12
12
12
15
25.7
30
10
10
10
8.6
15
14
14
14
25.7
30
10
10
10
0
13.3
20
14
14
14
9
16.2
20
12
12
12
11.6
20
14
14
14
16.2
20
12
12
12
15
25.7
30
10
10
10
11.6
20
14
14
14
25.7
30
10
10
10
0
22.5
35
10
10
10
5
26.6
35
10
10
10
8
41.2
45
6
8
8
10
51.6
60
6
6
8
15
76.6
80
3
4
4
50.0
60
6
8
8
26.6
30
10
10
10
0
31.1
50
8
8
8
5
31.1
50
8
8
8
8
43.5
50
6
8
8
10
53.9
60
6
6
8
15
78.9
80
3
4
4
50
60
6
8
8
28.9
30
10
10
10
20
103.9
110
1
2
3
50
60
6
8
8
53.9
60
6
6
8
0
40.6
60
6
8
8
5
40.6
60
6
8
8
8
43.5
60
6
8
8
10
53.9
60
6
6
8
15
78.9
80
3
4
4
50
60
6
8
8
28.6
30
10
10
10
20
103.9
110
1
2
3
37.5
60
8
8
8
53.9
60
6
6
8
0
28.4
45
10
10
10
9
31
45
8
8
8
25.3
40
10
10
10
31
35
8
8
8
15
49
50
6
8
8
25.3
40
10
10
10
49
50
6
8
8
Table 6. Large Package
AC Electrical
Data
50
60
6
8
8
50
60
6
8
8
Heater Model
kw
MOA
Q3RA-024K
0
14.9
20
14
14
14
5
39.9
40
8
8
8
8
54.4
60
6
6
8
10
64.9
70
4
6
6
0
20.4
30
10
10
10
5
45.4
50
6
8
8
8
60.0
60
4
6
6
10
70.4
80
3
4
15
95.4
100
1
3
Q3RA-03OK
MOP I 60°0 I 75°0 I 90°0
0
21.8
5 8
CopperWireSize MOP I 60°0 I 75°0 I 90°0
Copse, 75°C Wit iSize MOP I 60°C 90°C
14
14
14
51.4
60
6
6
8
6
18.3
30
12
12
12
52.1
60
6
6
8
3
43.3
50
6
8
8
52.1
60
6
6
8
18.3
30
12
12
12
27.1
30
10
10
10
8
35
10
10
10
46.8
50
6
8
8
61.4
60
4
6
6
10
71.8
80
3
4
6
19.7
30
12
12
12
52.1
60
6
6
15
96.8
100
1
3
3
44.7
50
6
8
8
52.1
60
6
6
8
19.7
30
12
12
12
27.1
30
10
10
10
0
25.8
40
10
5
50.8
60
8
65.4
70
10
75.8
15
100.8
MOA
CopperWireSize MOP I 60°0 I 75°0 I 90°0
52.1
60
6
6
8
50
60
6
8
8
10
10
6
6
8
4
4
6
23.7
40
10
10
10
41.7
45
6
8
8
80
3
4
4
23.7
40
10
10
10
52.1
60
6
6
8
110
1
2
3
48.7
60
6
8
8
52.1
60
6
6
8
23.7
40
10
10
10
30.2
35
8
8
8
50
60
6
8
8
23.7
40
10
10
10
52.1
60
6
6
8
50
60
6
8
8
15 (3 circuit) 125.8
150
0O
1
2
0
31.6
50
8
8
8
5
56.6
70
4
6
6
28.6
50
10
10
10
29.3
30
10
10
10
8
71.1
80
3
4
6
28.6
50
10
10
10
43.9
45
6
8
8
10
81.6
90
3
4
4
28.6
50
10
10
10
54.3
60
6
6
8
15 (3 circuit)
106.6
110
1
2
3
28.6
50
10
10
10
28
30
10
10
10
50
60
6
8
8
20 (3 circuii
131.6
150
00
0
1
28.6
50
10
10
10
53
60
6
6
8
50
60
6
8
8
0
38.1
60
8
8
8
5
63.1
80
4
6
6
35.1
60
8
8
8
29.3
30
10
10
10
8
77.6
90
3
4
4
35.1
60
8
8
8
43.9
45
6
8
8
10
88.1
100
2
3
4
35.1
60
8
8
8
54.3
60
6
6
8
15 (3 circuit)
113.1
125
0
2
2
35.1
60
8
8
8
28
30
10
10
10
50
60
6
8
8
20 (3 circuit)
138.1
150
0
0
1
35.1
60
8
8
8
53
60
6
6
8
50
60
6
8
8
0
15.4
25
12
12
12
5
40.4
45
6
8
8
8
54.9
60
6
6
8
10
65.4
70
4
4
6
14
20
14
14
14
51.1
60
6
6
8
0
20.1
30
10
10
10
5
45.1
50
6
8
8
8
59.6
60
4
6
6
10
70.1
80
3
4
6
18
30
12
12
12
52.1
60
6
6
8
15
95.1
100
1
3
3
43
50
6
8
8
52.1
60
6
6
8
18
30
12
12
12
27.1
30
10
10
10
50
60
6
8
8
50
60
6
8
8
20 (3 circuit) Q3RA-048K
Q3RA-060K
Q3RC-024K
Q3RC-030K
15 (3 circuit) Q3RC-036K
0
21.8
35
10
10
10
5
46.8
50
6
8
8
8
61.4
70
4
6
6
19.7
30
12
12
12
41.7
45
6
8
8
10
71.8
80
3
4
6
19.7
30
12
12
12
52.1
60
6
6
8
15
96.8
100
1
3
3
44.7
50
6
8
8
52.1
60
6
6
8
19.7
30
12
12
12
27.1
30
10
10
10
15 (3 circuil Q3RC-042K
0
22.7
35
10
10
10
5
47.7
50
6
8
8
8
62.2
70
4
6
6
20.6
35
10
10
10
41.7
45
6
8
8
10
72.7
80
3
4
6
20.6
35
10
10
10
52.1
60
6
6
8
15
97.7
100
1
3
3
45.6
50
6
8
8
52.1
60
6
6
8
20.6
35
10
10
10
30.2
35
8
8
8
50
60
6
8
8
20.6
35
10
10
10
52.1
60
6
6
8
50
60
6
8
8
15 (3 circuit) 122.7
125
O
1
2
28.3
45
10
10
10
5
53.3
60
6
6
8
8
67.9
70
4
4
6
25.3
40
10
10
10
42.6
45
6
8
8
80
3
4
4
25.3
40
10
10
10
53
60
6
6
8
110
1
2
3
50.3
60
6
6
8
53
60
6
6
8
25.3
40
10
10
10
28
30
10
10
10
50
60
6
8
8
25.3
40
10
10
10
53
60
6
6
8
50
60
6
8
8
20 (3 circuii Q3RC-048K
0
10 15
78.3
103.3
15 (3 circuit) 20 (3 circuii
128.3
150
0
1
2
Table 7. Small 10
MCA
20
15 (3 circuit) Q3RA-042K
MOA
Cilcuit C
13.5
15 (3 circuit) Q3RA-036K
Multiple Circuil Circuit B
Circuit A
Single circuit Copper Wire Size
Package
HP Electrical
Data
Multiple
Model P3RA-024K
P3RA-030K
P3RA-036K
P3RA-042K
P3RA-048K
P3RA-060K
P3RC-024K
P3RC-030K
P3RC-036K
P3RC-042K
P3RC-048K
Circuit
Circuit A
Single circuit Heater kw 0
MCA 14.9
5
26.8
30
10
10
10
8
41.3
45
6
8
8
10
51.8
60
6
6
8
0
20.4
30
10
10
10
5
27.6
30
10
10
10
8
42.2
45
6
8
8
10
52.6
60
3
4
4
15
77.6
80
3
4
4
0
21.8
35
10
10
10
5
27.6
35
10
10
10
8
42.2
45
6
8
8
10
52.6
60
6
6
8
15
77.6
80
3
4
4
0
25.8
40
10
10
10
5
27.6
40
10
10
10
8
42.2
45
6
8
8
10
52.6
60
6
6
8
15
77.6
80
3
4
20
102.6
110
1
0
31.6
50
5
31.6
8
43.3
10
cepperwire MOP I 60°CI 75°CI 20 14 14
size 90°C 14
MCA
Circuit
copper wire size MOP I 60°CI75°CI90°C
B
I 60°cl copper7Wire Size MCAMOP 5°Cl g0°C
50
60
6
8
8
27.6
30
10
10
10
50
60
6
8
8
27.6
30
10
10
10
4
50.0
60
6
8
8
27.6
30
10
10
10
2
3
50.0
60
6
8
8
52.6
60
6
6
8
8
8
8
50
8
8
8
50
6
8
8
53.8
60
6
6
8
15
78.8
80
3
4
4
53.8
60
6
6
8
28.8
30
10
10
10
20
103.8
110
1
2
3
53.8
60
6
6
8
53.8
60
6
6
8
0
38.1
60
8
8
8
5
38.1
60
8
8
8
8
43.3
60
6
8
8
10
53.8
60
6
6
8
15
78.8
80
3
4
4
53.8
60
6
6
8
20
103.8
110
1
2
3
53.8
60
6
6
8
28.8 53.8
30 60
10 6
10 6
10 8
0
15.4
25
12
12
12
5
26.8
30
10
10
10
8
41.3
45
6
8
8
10
51.8
60
6
6
8
0
20.1
30
12
12
12
5
27.6
30
10
10
10
8
42.2
45
6
8
8
10
52.6
60
6
6
8
15
77.6
80
3
4
4
50
60
6
8
8
27.6
30
10
10
10
0
21.7
35
10
10
10
5
27.6
35
10
10
10
8
42.2
45
6
8
8
10
52.6
60
6
6
8
15
77.6
80
3
4
4
50
60
6
8
8
27.6
30
10
10
10
0
22.7
35
10
10
10
5
27.6
35
10
10
10
8
42.2
45
6
8
8
10
52.6
60
6
6
8
15
77.6
80
3
4
4
50
60
6
8
8
27.6
30
10
10
10
20
102.6
110
1
2
3
50
60
6
8
8
52.6
60
6
6
8
0
28.3
45
10
10
10
5
28.3
45
10
10
10
8
43.3
45
6
8
8
10
53.8
60
6
6
8
15
78.8
80
3
4
4
50
60
6
8
8
28.8
30
10
10
10
20
103.8
110
1
2
3
50
60
6
8
8
53.8
60
6
6
8
Table 8. Small
Package
AC Electrical
Data 11
WD#1 1 PHASE 5 KW, 8 KW, OR 10 KW, 1 CIRCUIT
APPLICATIONS INCLUDE: SMALL PACKAGE: Q3RA/C -024K(S&8 _) Q3RA/C -030K(S&8 _) Q3RA/C - 036K (5 kw) Q3RA/C - 042K (5 kw) P3RA/C - 024K (5, 8, & 10 P3RA/C - 030K (5, 8, & 10 P3RA/C - 042K (5, 8, & 10 P3RA/C - 048K (5, 8, & 10 P3RA/C - 060K (5, 8, & 10
(8 kw and 10 kw shown)
LARGE Q4SA/C P4SA/C P4SA/C P4SA/C
PACKAGE: - 036K (5 - 036K (5, - 048K (5, - 060K (5,
kw) 8, & 10 kw) 8, & 10 kw) 8, & 10 kw)
kw) kw) kw) kw) kw)
m
WHITE
2
_
BLACK
3 41
--BROWN--
5
_BLUE_ _ORANGE_
7
--GRAY
i -
--
8 9 i
BLACK --
\
FIELD
BLACK --
HEATER
WIRING
KIT PLUG
H
c°gP S[°2 ,,
mmmmmnmmm|
FACTORY LOW VOLTAGE HIGH
III
WIRING
VOLTAGE
[]
[]
$)-
C,RCU,T
BREAKER
J J
CIRCUIT A
12
WD #2 I PHASE 5 KW, 8 KW, OR 10 KW, 2 CIRCUIT
(8 kw and 10 kw shown)
APPLiCATiONS iNCLUDE: SMALL PACKAGE: Q3RA/C Q3RNC Q3RNC Q3RNC Q3RA Q3RC Q3RA -
LARGE
- 020K (10 kw) - 030K (10 kw) - 036K (8 & 10 kw) - 042K (8 & 10 kw) 048K (5, 8, & 10 kw) 048K (8 & 10 kw) 060K (5, 8, & 10 kw)
PACKAGE:
Q4SA/C - 036K (8 & 10 kw) Q4SA/C - 048K (5, 8, & 10 kw) Q4SA/C - 060K (5, 8, & 10 kw)
WHITE
K
BLUE_ __
_ORANGE
_ R
GRAY
=
--GRAY-- --
_
HEA_ER
K(T PLUG
COMPRESSOR CONTACTOR
°lMl° k _L2 m
TERMINAL BLOCK (NOT NECESSARY FOR10SEER HP)
LI m
m
FIELD
WIRING
mmmmmmmmmm
FACTORY LOW VOLTAGE HiGH
VOLTAG_
WIRING
m []
[]
[] []
CIRCUIT A [] []
m []
CIRCUIT B
13
W_ i PHASE 15 KW, 2 CiRCUiT
APPLiCATiONS iNCLUDE: LARGE PACKAGE: P4SNC - 036K P4SA/C - 048K P4SNC - 060K
(Air Conditioning
SMALL P3RA/C P3RA/C P3RA/C P3RA/C
Application)
PACKAGE: - 030K - 036K - 042K - 048K
CONTACTOR RED_ RED_ ELEMENTS
CONTACTOR ELEMENTS
GRAY_
L
BLACK BLACK
HEATER KiT PLUG
FIELD WIRING
BLACK
mmmmmmmmm|
FACTORY LOW VOLTAGE
W_RING []
[]
HIGH VOLTAGE
BREAKER
m m
m m
CIRCUIT A
14
WD#4 I PHASE 15 KW, 2 CiRCUiT
(Heat
Pump
APPLiCATiONS iNCLUDE: LARGE PACKAGE: SMALL Q4SA - 036K Q3RA/C Q4SC - 036K Q3RA/C Q3RA/C Q3RC -
Application)
PACKAGE: - 030K - 036K - 042K 048K
ELEMENTS
ELEMENTS
] BLACK BLACK
L
HEATER BLACK_
KIT PLUG
COMPRESSOR CONTACTOR
T2
IT1
_L2 FIELD
WIRING
Im Im m FACTORY
LOW HiGH
VOLTAGE VOLTAGE
m m
WIRING
Im Im Im m
L1
II
! m
TERMINAL
[]
[]
BREAKER
CIRCUIT )__ [] []
CIRCUNT
__
[]
[] []
BLOCK
[] []
[] []
A
CIRCUIT
B
15
WD#5 I PHASE 15 KW, 3 CIRCUIT
APPLiCATiONS iNCLUDE: SMALL PACKAGE: Q3RA/C - 042K Q3RA/C - 048K Q3RA - 060K
LARGE Q4SA/C Q4SA/C P4SA/C
PACKAGE: - 048K - 060K - 060K
CONTACTOR
ELEMENTS
BLACK
= ELEMENTS
GRAYq BLACK BLACK
BLACK
COMPRESSOR CONTACTOR
FIELD
WIR$NG Im m _m_mlm FACTORY WIRING
[] [] [] [] [] []
m u=|
LOW VOLTAGE HIGH
VOLTAGE
[] []
[] [] [] [] [] []
[] []
CIRCUIT A
16
[]
[] []
[] m
C)RCUIT C
[] []
[]
[] []
CIRCUIT B
WD#6 1 PHASE 20 KW, 2 CIRCUIT
APPLICATIONS iNCLUDE: SMALL PACKAGE: P3RNC - 042K P3RNC - 048K P3RA/C - 060K
LARGE PACKAGE: P4SA/C - 048K
I I I I I
ELEMENTS
ELEMENTS
,BLACK,
HEATER
KIT PLUG
=BLACKI 'BLACK
COMPRESSOR CONTACTOR
m
[]
CIRCUIT BREAKER
[] []
[] [] CIRCUIT
B
[] []
[] [] CIRCUmT
A
17
WD#7 1 PHASE 20 KW, 3 CIRCUIT
APPLICATIONS INCLUDE: SMALL PACKAGE: Q3RA/C - 042K Q3RA/C - 048K Q3RA - 060K
LARGE PACKAGE: Q4SA/C - 048K Q4SA/C - 060K P4SA/C - 060K
3 ELEMENTS
4
8
ELEMENTS
BLACK BLACK BLACK
KIT PLUG
BLACK
COMPRESSOR CONTACTOR
TM
FfELD WfRING
Im Im Im Im Iwl Im Im Im m |
FACTORY LOW VOLTAGE H_GH VOLTAGE
W_RING
I 1
[] 1
TERMINAL []
_i_
18
[] []
[] []
ClRCUIT
A
BREAKER
[] []
[] [] CIRCUIT
[]
C
[] []
m []
ClRCUNT B
BLOCK
WD#8 3 PHASE, 208/230V 9 OR 15 KW, I CiRCUiT APPLiCATiONS P4SA P4SA P4SA P4SC Q4SA Q4SA
-
036C 048C 060C 060C 036C 048C
iNCLUDE: (9 & 15 (9 & 15 (9 & 15 (9 & 15 (9 kw) (9 kw)
kw) kw) kw) kw)
COMPRESSOR
FACTORY WIRING LOW VO LTA%EFIELD WIRING mmmllmllmm HIGH VOLTAGE
CONTACTOR
1 =
TERMINAL BLOCK
ELEMENT
ELEMENT
ELEMENT
HEATER
KIT PLUG
19
WD#9 3 PHASE, 208/230V 9 OR 15 KW, 2 CIRCUIT APPLICATIONS
INCLUDE:
Q4SA - 036C (15 kw) Q4SA - 048C (15 kw) Q4SA - 060C (9 & 15 kw)
CIRCUIT
A
I | |
l
i_
FIELD
CIRCUIT BREAKER
L11(_I
COMPRESSORcoNTACTO R
WIRING
mlimll
FACTORY LOW VOLTAGE HIGH
ELEMENT
I==== ORANGE
2O
VOLTAGE
m ! m mla m = WIRING
WD#10 3 PHASE, 460V 9 OR 15 KW, 1 CiRCUiT APPLiCATiONS Q4SA - 036D (9 Q4SA - 048D (9 Q4SA - 060D (9 P4SA - 036D (9 P4SA - 048D (9 P4SA - 060D (9
iNCLUDE: & 15 kw) & 15 kw) & 15 kw) & 15 kw) & 15 kw) & 15 kw)
H
H
H
"L3_tL2 _t' _
TT,T_,TI
COMPRESSOR CONTACTOR
FIELD
WIRING
==m==m==
FACTORY LOW
VOLTAGE
HIGH
VOLTAGE
WIRING
YELLOW
RED --
ELEMENT
__
2:
ELEMENT
ELEMENT _°ROW iHEATER KIT PLUG
21
WD#11 3 PHASE, 460V 9 OR 15 KW, 2 CIRCUIT APPLICATIONS Q4SA - 036D (9 Q4SA - 048D (9 Q4SA - 060D (9 P4SA - 036D (9 P4SA - 048D (9 P4SA - 060D (9
INCLUDE: & 15 kw) & 15 kw) & 15 kw) & 15 kw) & 15 kw) & 15 kw)
CIRCUIT | | | | |
CIRCUIT
B
ClRCUtT
A
I I I I I
BREAKER
!J
CtRCUIT
BREAKER
BLACK
---(?L3
=_2
11(_L
COMPRESSO
_T3
_T2
"_TI"_
R
_YELLOW_
I
CONTACTOR
_RED_
FIELD
WIRING
mmmmmmmm
FACTORY LOW
VOLTAGE
HIGH
VOLTAGE
WIRING
LIMIT
1
ELEMENT
0 ELEMENT O
=ORANGE
ELEMENT
CI_NIT
HEATER
22
KIT PLUG
BROW i -
23
INSTALLER PLEASE LEAVE THESE iNSTALLATiON iNSTRUCTiONS WITH THE UNiT OWNER.
III lllllllrllllllllllllll II!
7083400 Specifications and illustrations subject to change without notice and without incurring obligations. Printed inU.S.A. (02/04)
