WASTE-MATE SERIES
SECTION: 2.20.070 FM2793 0517 Supersedes 0215
Your Peace of Mind is Our Top Priority ® ®
Product information presented here reflects conditions at time of publication. Consult factory regarding discrepancies or inconsistencies.
TECHNICAL DATA SHEET
WASTE-MATE SERIES
Models 404/4404, 405/4405 Submersible Sewage Pumps
MATERIALS
PUMP
MOTOR
PRODUCT SPECIFICATIONS Horse Power
2 (404/4404) or 3 (405/4405)
Voltage
200 - 575
Phase
1 or 3 Ph
Hertz
60 Hz
RPM
1750
Type
Permanent split capacitor or 3 Ph
Insulation
Class B
Amps
4.1 - 20.2
Operation
Automatic or nonautomatic
Discharge Size
4" horizontal ANSI flange
Solids Handling
3" (76 mm) spherical solids
Cord Length
20' (6 m) standard
Cord Type
1 Ph-UL listed 3-wire neoprene cord and plug 3 Ph-4-wire with no plug
Max. Head
38' (11.6 m)
Max. Flow Rate
361 GPM (1367 LPM)
Max. Operating Temp.
130 °F (54 °C)
Cooling
Oil filled
Motor Protection
Auto reset thermal overload (1 Ph)
Upper Bearing
Ball bearing
Lower Bearing
Ball bearing
Mechanical Seals
Carbon and ceramic
Impeller Type
Non-clogging vortex
Impeller
Cast iron
Hardware
Stainless steel
Motor Shaft
1117 carbon steel or 416 stainless steel*
Gasket
Neoprene square ring and gasket
SINGLE SEAL
RO
TA
TI
ON
6-1/4” (159 mm)
9-7/8” (251 mm)
26” (660 mm) 22-7/8” (581 mm)
6-1/4” (159 mm)
SK1788
DOUBLE SEAL
6-1/4” (159 mm)
9-7/8” (251 mm)
*Single seal models are built with a carbon steel motor shaft, and double seal models are built with a stainless steel motor shaft. All Class 30 cast iron construction. NOTE: The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with nonautomatic pumps. NOTE: See model comparison chart for specific details.
27-1/2” (699 mm) 24-3/8” (619 mm)
4” DISCHARGE 125 LB ANSI FLANGE
6-1/4” (159 mm)
SK1787 R
Certified to CSA Standard 227875
UL R
Tested to UL778 CSA Standard C22.2 No. 108
© Copyright 2017 Zoeller® Co. All rights reserved. 502-778-2731 | 800-928-7867 | 3649 Cane Run Road | Louisville, KY 40211-1961 | www.zoeller.com
Feet Meters 5 1.5 10 3.0 15 4.6 20 6.1 25 7.6 30 9.1 35 10.7 Shut-off Head:
404/4404
405/4405
Gal. Liters 300 1136 265 1003 224 848 184 698 134 503 60 227 --33 ft.(10.1m)
FEET 40
12
PUMP PERFORMANCE CURVE MODELS 404/4404/405/4405 3" SOLIDS CAPACITY
35
Gal. Liters 361 1367 326 1234 284 1075 241 912 197 746 134 507 50 189 38 ft.(11.6m)
10 TOTAL DYNAMIC HEAD
MODEL
METERS
TOTAL DYNAMIC HEAD/FLOW PER MINUTE TOTAL DYNAMICAND HEAD FLOW PER MINUTE SEWAGE DEWATERING
30 405/4405
8
25 20
6
15
4
10 404/4404
2
5
0 GALLONS LITERS 0
50 200
100 400
150 600
200
250
800
300
1000
1200
350
400
1400 012116
FLOW PER MINUTE
MODEL COMPARISON
Model
Seal
Mode
Volts
Ph
Amps
HP
Hz
Lbs
Kg
Simplex
Duplex
E404
Single
Non
230
1
12.9
2
60
136
61
1 or 2
3
E4404
Double
Non
230
1
12.9
2
60
147
66
1 or 2
3
WD404
Single
Auto
230
1
12.9
2
60
139
63
**
---
WD4404
Double
Auto
230
1
12.9
2
60
150
68
**
---
I404
Single
Non
200
1
14.4
2
60
136
61
2
3
I4404
Double
Non
200
1
14.4
2
60
147
66
2
3
J404
Single
Non
200
3
13.8
2
60
136
61
2
3
J4404
Double
Non
200
3
13.8
2
60
147
66
2
3
F404
Single
Non
230
3
10.5
2
60
136
61
2
3
F4404
Double
Non
230
3
10.5
2
60
147
66
2
3
G404
Single
Non
460
3
5.2
2
60
136
61
2
3
G4404
Double
Non
460
3
5.2
2
60
147
66
2
3
BA404
Single
Non
575
3
4.1
2
60
136
61
2
3
BA4404
Double
Non
575
3
4.1
2
60
147
66
2
3
*E405
Single
Non
230
1
19.0
3
60
136
61
1 or 2
3
*E4405
Double
Non
230
1
19.0
3
60
136
61
1 or 2
3
*WD405
Single
Auto
230
1
19.0
3
60
139
63
**
---
*WD4405
Double
Auto
230
1
19.0
3
60
150
68
**
---
I405
Single
Non
200
1
20.2
3
60
136
61
2
3
I4405
Double
Non
200
1
20.2
3
60
145
65
2
3
J405
Single
Non
200
3
14.8
3
60
136
61
2
3
J4405
Double
Non
200
3
14.8
3
60
147
66
2
3
F405
Single
Non
230
3
12.2
3
60
136
61
2
3
F4405
Double
Non
230
3
12.2
3
60
147
66
2
3
G405
Single
Non
460
3
6.1
3
60
136
61
2
3
G4405
Double
Non
460
3
6.1
3
60
147
66
2
3
BA405
Single
Non
575
3
4.1
3
60
136
61
2
3
BA4405
Double
Non
575
3
4.1
3
60
147
66
2
3
*CSA approved, all other models are UL and cCSAus approved. Additional cord lengths are available in 25' (8 m), 35' (11 m) and 50' (15 m).
SELECTION GUIDE 1. For automatic use single piggyback variable level float switch or double piggyback variable level float switch. Refer to FM0477.
CAUTION
2. See FM1228 for correct model of simplex control panel. 3. See FM0712 for correct model of duplex control panel.
All installation of controls, protection devices and wiring should be done by a qualified licensed electrician. All electrical and safety codes should be followed including the most recent National Electrical Code (NEC) and the Occupational Safety and Health Act (OSHA).
© Copyright 2017 Zoeller® Co. All rights reserved. 502-778-2731 | 800-928-7867 | 3649 Cane Run Road | Louisville, KY 40211-1961 | www.zoeller.com
Your Peace of Mind is Our Top Priority ® ®
Product information presented here reflects conditions at time of publication. Consult factory regarding discrepancies or inconsistencies.
TECHNICAL DATA SHEET
WASTE-MATE SERIES
Models 404/4404, 405/4405 Submersible Sewage Pumps
MATERIALS
PUMP
MOTOR
PRODUCT SPECIFICATIONS Horse Power
2 (404/4404) or 3 (405/4405)
Voltage
200 - 575
Phase
1 or 3 Ph
Hertz
60 Hz
RPM
1750
Type
Permanent split capacitor or 3 Ph
Insulation
Class B
Amps
4.1 - 20.2
Operation
Automatic or nonautomatic
Discharge Size
4" horizontal ANSI flange
Solids Handling
3" (76 mm) spherical solids
Cord Length
20' (6 m) standard
Cord Type
1 Ph-UL listed 3-wire neoprene cord and plug 3 Ph-4-wire with no plug
Max. Head
38' (11.6 m)
Max. Flow Rate
361 GPM (1367 LPM)
Max. Operating Temp.
130 °F (54 °C)
Cooling
Oil filled
Motor Protection
Auto reset thermal overload (1 Ph)
Upper Bearing
Ball bearing
Lower Bearing
Ball bearing
Mechanical Seals
Carbon and ceramic
Impeller Type
Non-clogging vortex
Impeller
Cast iron
Hardware
Stainless steel
Motor Shaft
1117 carbon steel or 416 stainless steel*
Gasket
Neoprene square ring and gasket
SINGLE SEAL
RO
TA
TI
ON
6-1/4” (159 mm)
9-7/8” (251 mm)
26” (660 mm) 22-7/8” (581 mm)
6-1/4” (159 mm)
SK1788
DOUBLE SEAL
6-1/4” (159 mm)
9-7/8” (251 mm)
*Single seal models are built with a carbon steel motor shaft, and double seal models are built with a stainless steel motor shaft. All Class 30 cast iron construction. NOTE: The sizing of effluent systems normally requires variable level float(s) controls and properly sized basins to achieve required pumping cycles or dosing timers with nonautomatic pumps. NOTE: See model comparison chart for specific details.
27-1/2” (699 mm) 24-3/8” (619 mm)
4” DISCHARGE 125 LB ANSI FLANGE
6-1/4” (159 mm)
SK1787 R
Certified to CSA Standard 227875
UL R
Tested to UL778 CSA Standard C22.2 No. 108
© Copyright 2017 Zoeller® Co. All rights reserved. 502-778-2731 | 800-928-7867 | 3649 Cane Run Road | Louisville, KY 40211-1961 | www.zoeller.com
Feet Meters 5 1.5 10 3.0 15 4.6 20 6.1 25 7.6 30 9.1 35 10.7 Shut-off Head:
404/4404
405/4405
Gal. Liters 300 1136 265 1003 224 848 184 698 134 503 60 227 --33 ft.(10.1m)
FEET 40
12
PUMP PERFORMANCE CURVE MODELS 404/4404/405/4405 3" SOLIDS CAPACITY
35
Gal. Liters 361 1367 326 1234 284 1075 241 912 197 746 134 507 50 189 38 ft.(11.6m)
10 TOTAL DYNAMIC HEAD
MODEL
METERS
TOTAL DYNAMIC HEAD/FLOW PER MINUTE TOTAL DYNAMICAND HEAD FLOW PER MINUTE SEWAGE DEWATERING
30 405/4405
8
25 20
6
15
4
10 404/4404
2
5
0 GALLONS LITERS 0
50 200
100 400
150 600
200
250
800
300
1000
1200
350
400
1400 012116
FLOW PER MINUTE
MODEL COMPARISON
Model
Seal
Mode
Volts
Ph
Amps
HP
Hz
Lbs
Kg
Simplex
Duplex
E404
Single
Non
230
1
12.9
2
60
136
61
1 or 2
3
E4404
Double
Non
230
1
12.9
2
60
147
66
1 or 2
3
WD404
Single
Auto
230
1
12.9
2
60
139
63
**
---
WD4404
Double
Auto
230
1
12.9
2
60
150
68
**
---
I404
Single
Non
200
1
14.4
2
60
136
61
2
3
I4404
Double
Non
200
1
14.4
2
60
147
66
2
3
J404
Single
Non
200
3
13.8
2
60
136
61
2
3
J4404
Double
Non
200
3
13.8
2
60
147
66
2
3
F404
Single
Non
230
3
10.5
2
60
136
61
2
3
F4404
Double
Non
230
3
10.5
2
60
147
66
2
3
G404
Single
Non
460
3
5.2
2
60
136
61
2
3
G4404
Double
Non
460
3
5.2
2
60
147
66
2
3
BA404
Single
Non
575
3
4.1
2
60
136
61
2
3
BA4404
Double
Non
575
3
4.1
2
60
147
66
2
3
*E405
Single
Non
230
1
19.0
3
60
136
61
1 or 2
3
*E4405
Double
Non
230
1
19.0
3
60
136
61
1 or 2
3
*WD405
Single
Auto
230
1
19.0
3
60
139
63
**
---
*WD4405
Double
Auto
230
1
19.0
3
60
150
68
**
---
I405
Single
Non
200
1
20.2
3
60
136
61
2
3
I4405
Double
Non
200
1
20.2
3
60
145
65
2
3
J405
Single
Non
200
3
14.8
3
60
136
61
2
3
J4405
Double
Non
200
3
14.8
3
60
147
66
2
3
F405
Single
Non
230
3
12.2
3
60
136
61
2
3
F4405
Double
Non
230
3
12.2
3
60
147
66
2
3
G405
Single
Non
460
3
6.1
3
60
136
61
2
3
G4405
Double
Non
460
3
6.1
3
60
147
66
2
3
BA405
Single
Non
575
3
4.1
3
60
136
61
2
3
BA4405
Double
Non
575
3
4.1
3
60
147
66
2
3
*CSA approved, all other models are UL and cCSAus approved. Additional cord lengths are available in 25' (8 m), 35' (11 m) and 50' (15 m).
SELECTION GUIDE 1. For automatic use single piggyback variable level float switch or double piggyback variable level float switch. Refer to FM0477.
CAUTION
2. See FM1228 for correct model of simplex control panel. 3. See FM0712 for correct model of duplex control panel.
All installation of controls, protection devices and wiring should be done by a qualified licensed electrician. All electrical and safety codes should be followed including the most recent National Electrical Code (NEC) and the Occupational Safety and Health Act (OSHA).
© Copyright 2017 Zoeller® Co. All rights reserved. 502-778-2731 | 800-928-7867 | 3649 Cane Run Road | Louisville, KY 40211-1961 | www.zoeller.com
