flat base tv stand 1 - Displays2go
FLAT BASE TV STAND Parts A. B. C1. C2. D1. D2. E. F.
Instructions Metal Base Lower Round Tubing Lower Round Tubing Upper Round Tubing Upper Round Tubing Tubing Connector Pan Head Screw
1 1 1 1 1 1 2 12
(Left) (Right) (Left) (Right)
CAUTION: METAL BASE IS HEAVY! 2 PERSONS LIFT/MOVE TO PREVENT ANY PHYSICAL INJURY.
A
B
E
F
C1
C2
D1
D2
*Hex Key for Part F can be found inside the TV Bracket box. (DUOPOLEBK)
PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE START THE ASSEMBLING. Open small box, lay out 4 long Tubings (C1, C2, D1, D2) on a flat surface. See picture below to identify where each tubing goes to (upper or lower, left or right).
1
3b
RIGHT VIEW
BACK VIEW
BACK VIEW
LEFT VIEW
3a
2 2
Lower Left Tubing
D2
C1
RIGHT VIEW
Upper Right Tubing
BACK VIEW
BACK VIEW
LEFT VIEW
Upper Left Tubing D1
Lower Right Tubing C2
**1. One or more upper/lower tubing may have holes on both sides. 2. Make sure each tubing has at least one pair of 2 holes facing outward (see detail 2). 3. Arrange tubings with one pair holes (see detail 3a), then sort tubings with two pairs holes (see detail 3b) to open places.
55 Broadcommon Road Bristol, RI 02809, USA
Phone: 1-800-572-2194 1-401-247-0333 (Int'l) Fax: 1-401-247-0392
1
FLAT BASE TV STAND
2
CAUTION: HEAVY METAL BASE CAN CAUSE MUSCLE STRAIN OR BACK INJURY. Fix Tubing Connector (Part E) on top of the Before assembling, remove packing materials. Lower Tubing. Carefully place the Metal Base (Part B) on a hard, flat ground.
4
Holes at top of Lower Tubings should face outward, to align with the holes on Tubing Connectors. (See STEP 4)
C1
E
Insert Tubing Connectors (Part E) into the Fixed Lower Tubings. Hold it in place when lining up holes. (Align with the top holes on Lower Tubings)
C2 Insert 4 Screws (Part F) through Lower Tubings into Connectors. Fasten screws with hex key.
Insert Lower Tubing into the upright on the Metal Base.
Ensure slot cutouts on uprights and Lower Tubings align with each other.
Insert Upper Tubings with Connectors.
D1
D2
Ensure the 2 slot cutouts are facing the same direction as other cutouts on the Lower Tubings.
B
3
5
Fix Lower Tubings by tightening 4 screws at bottom of the TV Stand. Insert Upper Tubings (Part D) intoTubing Connectors from above. The holes should line up with the holes on Connectors. Fasten 4 Screws (Part F) with hex key.
F Fasten 4 Screws (Part F) with hex key.
All screws must be securely tightened before using TV Stand.
Still have questions? No worry. If you’re confused during any step of the way, just call the number located at the bottom of the Instructions pages. Our friendly representative will be more than happy to help you.
55 Broadcommon Road Bristol, RI 02809, USA
Phone: 1-800-572-2194 1-401-247-0333 (Int'l) Fax: 1-401-247-0392
2
Instructions Metal Base Lower Round Tubing Lower Round Tubing Upper Round Tubing Upper Round Tubing Tubing Connector Pan Head Screw
1 1 1 1 1 1 2 12
(Left) (Right) (Left) (Right)
CAUTION: METAL BASE IS HEAVY! 2 PERSONS LIFT/MOVE TO PREVENT ANY PHYSICAL INJURY.
A
B
E
F
C1
C2
D1
D2
*Hex Key for Part F can be found inside the TV Bracket box. (DUOPOLEBK)
PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE START THE ASSEMBLING. Open small box, lay out 4 long Tubings (C1, C2, D1, D2) on a flat surface. See picture below to identify where each tubing goes to (upper or lower, left or right).
1
3b
RIGHT VIEW
BACK VIEW
BACK VIEW
LEFT VIEW
3a
2 2
Lower Left Tubing
D2
C1
RIGHT VIEW
Upper Right Tubing
BACK VIEW
BACK VIEW
LEFT VIEW
Upper Left Tubing D1
Lower Right Tubing C2
**1. One or more upper/lower tubing may have holes on both sides. 2. Make sure each tubing has at least one pair of 2 holes facing outward (see detail 2). 3. Arrange tubings with one pair holes (see detail 3a), then sort tubings with two pairs holes (see detail 3b) to open places.
55 Broadcommon Road Bristol, RI 02809, USA
Phone: 1-800-572-2194 1-401-247-0333 (Int'l) Fax: 1-401-247-0392
1
FLAT BASE TV STAND
2
CAUTION: HEAVY METAL BASE CAN CAUSE MUSCLE STRAIN OR BACK INJURY. Fix Tubing Connector (Part E) on top of the Before assembling, remove packing materials. Lower Tubing. Carefully place the Metal Base (Part B) on a hard, flat ground.
4
Holes at top of Lower Tubings should face outward, to align with the holes on Tubing Connectors. (See STEP 4)
C1
E
Insert Tubing Connectors (Part E) into the Fixed Lower Tubings. Hold it in place when lining up holes. (Align with the top holes on Lower Tubings)
C2 Insert 4 Screws (Part F) through Lower Tubings into Connectors. Fasten screws with hex key.
Insert Lower Tubing into the upright on the Metal Base.
Ensure slot cutouts on uprights and Lower Tubings align with each other.
Insert Upper Tubings with Connectors.
D1
D2
Ensure the 2 slot cutouts are facing the same direction as other cutouts on the Lower Tubings.
B
3
5
Fix Lower Tubings by tightening 4 screws at bottom of the TV Stand. Insert Upper Tubings (Part D) intoTubing Connectors from above. The holes should line up with the holes on Connectors. Fasten 4 Screws (Part F) with hex key.
F Fasten 4 Screws (Part F) with hex key.
All screws must be securely tightened before using TV Stand.
Still have questions? No worry. If you’re confused during any step of the way, just call the number located at the bottom of the Instructions pages. Our friendly representative will be more than happy to help you.
55 Broadcommon Road Bristol, RI 02809, USA
Phone: 1-800-572-2194 1-401-247-0333 (Int'l) Fax: 1-401-247-0392
2
