GSA Floor Fix Tile Adhesive
FLOOR FIX TILE ADHESIVE Descrip(on GSA FLOORFIX is an economical, cement based floor :le adhesive for the fixing of ceramic :les in indoor and covered outdoor situa:ons. It can be used over concrete floors or sand and cement screeded floors. The adhesive is recommended for fixing ceramic, quarry :les, slate and natural stone e.g., sandstone. Surface prepara(on The surface must be clean, true and free from dust, oil, laitance etc. Concrete Concrete floors must be at least 4 weeks old. Steel trowelled surfaces must be roughened mechanically prior to :ling. A wood float finish is the recommended surface for :ling using GSA FLOORFIX. Sand Cement Screed The screed is to consist of one part cement to three or four parts sand.
WA Phone - (08) 9353 3354 VIC Phone - (03) 9763 4433 NSW Phone - (02) 9673 1322 [email protected]
Leave the screed with a wood float finish to establish a mechanical key. Allow screed at least 7 days to cure prior to :ling. It should be approximately 15mm in thickness for fully bonded screed and 40mm minimum for selfsuppor:ng screed. Mixing The mixed material is usable for up to 2 hours. 1. Use approximately 3.5L of water with 15kg of the powder. 2. Add powder to clean water in a suitable container and mix to a thick creamy consistency. 3. Allow to stand for 5 minutes, re-s:r the mixture thoroughly and it is ready for use. So not add addi:onal water. Applica(on 1. Apply the GSA FLOORFIX to the surface with a 10 x 10 x 10mm notched trowel to achieve 100% coverage on the back of the :le. 2. Spread only 1 square metre at a :me and ensure a skin has not developed on the adhesive before bedding the :les. 3. Press and slide the :le into posi:on ensuring the whole of the back of the :le is in good contact with the adhesive. Deeply keyed quarry :les and some extruded :les may require buVering of the adhesive on the back of the :les to ensure 100% coverage. 4. The final adhesive bed must not be less than 3mm thick or more than 10mm and should have a final joint width of approximately 3-10mm. Use :le spacers if desired to ensure even spacing.
WA Phone - (08) 9353 3354 VIC Phone - (03) 9763 4433 NSW Phone - (02) 9673 1322 [email protected]
5. Remove any surplus adhesive on face of the :le or between joints before it sets. 6. Adjustment of :les should be carried out within 15 minutes of laying (at 23°c and 50% rela:ve humidity) Coverage The coverage below is for 20kg of GSA FLOORFIX. Coverage will vary depending on the condi:on of the surface being :led and applica:on technique. As a general guide coverage will be 3.7m² using a 10mm notch trowel. Drying (me Full traffic should be possible a^er 24 hours (at 23°c and 50% rela:ve humidity). Allow longer for dense :les/substrates humid climates and low temperatures. Grou(ng Wait un:l adhesive has set firmly. This takes approximately 24 hours. Remove :le spaces and apply a suitable grout. Movement joints Movement joints must be in accordance with AS 3958.1:2077. As a general guide, movement joints should be incorporated at 4.5 metre intervals and around the perimeter of the floor. These joints must be approximately 6mm wide and kept free from adhesive and grout. Any structural movement joints must be carried through to the face of the :ling. They should be filled with a suitable flexible material such as GSA COLOURED SILICONE.
WA Phone - (08) 9353 3354 VIC Phone - (03) 9763 4433 NSW Phone - (02) 9673 1322 [email protected]
Shelf life A shelf life of 12 months is expected when stored in a dry place in iriginal unopened container at 30°c and 50% rela:ve humidity. Always re-seal bag air :ght a^er use. Packaging Product Code FFTA20 20kg bag 54 bags per pallet Cau(on Do not use in con:nuous immersed condi:ons such as swimming pools. Do not use over :mber floors. Do not use GSA FLOORFIX over concrete slabs subject to shrinkage and other movement. Use in conjunc:on with the GSA PRIMER AND ADDITIVE in exposed outdoor situa:ons by replacing all of the water in the mixing process. GSA guarantee Product is guaranteed for 10 years when installed to manufacturer’s instruc:ons. Manufactured under a quality system cer:fied as complying with ISO 9001 by an accredited cer:fied body. Technical details Characteris(cs of product: Colour and form: Grey powder Bulk Density 1.6kg/litre
WA Phone - (08) 9353 3354 VIC Phone - (03) 9763 4433 NSW Phone - (02) 9673 1322 [email protected]
Applica(on Proper(es (at 23°c and 50% rela(ve humidity) Mixing ra:o 100:23 (powder: water) Open :me: approx. 15 minutes Adjustability :me: approx. 25 minutes Sagging none Pot life 2 hours Mechanical Proper(es: AS4992.1 MEETS Sheer Bond Strength (Mpa): 7 days dry >1.0 Yes 14 days >1.5 Yes 28 days . 7 days water immersion >1.0 Yes Tensile Strength (Mpa) 7 days dry >0.15 Yes Safety Keep out of reach of children. Use gloves to prevent skin irrita:on. Avoid inhaling dust by using a dust mask. Wash immediately with plenty if water if material enters the eyes. Material Safety Data Sheet (MSDS) available in GSA website. Disclaimer Campbell Wholesale Pty Ltd believes that the informa:on in this technical data sheet is an accurate descrip:on of the typical uses of the product. The data and statements are based on our research and development work and is to the best of our knowledge true and accurate. The user must ensure of the product(s) in their applica:on prior to use in par:cular to determine its performance, efficiency and safety.
WA Phone - (08) 9353 3354 VIC Phone - (03) 9763 4433 NSW Phone - (02) 9673 1322 [email protected]
The use of this product is beyond the manufacturer’s control, and liability is restricted to the replacement of material proven faulty. The manufacturer is not responsible for any loss or damage arising from incorrect usage. Products conform solely to the informa:on contained in this and other related Campbells Wholesale Pty Ltd publica:ons. Campbells Wholesale Pty Ltd reserves the right to make changes to specifica:ons and informa:on related to the products at any :me. Users are asked to check that the literature in their possession is the latest issue. Statements contained herein should not be considered as a warranty of any kind, expressed or implied in describing the performance or suitability of the product for a par:cular applica:on. No liability is accepted for infringement of any patents or any other intellectual property right.
WA Phone - (08) 9353 3354 VIC Phone - (03) 9763 4433 NSW Phone - (02) 9673 1322 [email protected]
WA Phone - (08) 9353 3354 VIC Phone - (03) 9763 4433 NSW Phone - (02) 9673 1322 [email protected]
Leave the screed with a wood float finish to establish a mechanical key. Allow screed at least 7 days to cure prior to :ling. It should be approximately 15mm in thickness for fully bonded screed and 40mm minimum for selfsuppor:ng screed. Mixing The mixed material is usable for up to 2 hours. 1. Use approximately 3.5L of water with 15kg of the powder. 2. Add powder to clean water in a suitable container and mix to a thick creamy consistency. 3. Allow to stand for 5 minutes, re-s:r the mixture thoroughly and it is ready for use. So not add addi:onal water. Applica(on 1. Apply the GSA FLOORFIX to the surface with a 10 x 10 x 10mm notched trowel to achieve 100% coverage on the back of the :le. 2. Spread only 1 square metre at a :me and ensure a skin has not developed on the adhesive before bedding the :les. 3. Press and slide the :le into posi:on ensuring the whole of the back of the :le is in good contact with the adhesive. Deeply keyed quarry :les and some extruded :les may require buVering of the adhesive on the back of the :les to ensure 100% coverage. 4. The final adhesive bed must not be less than 3mm thick or more than 10mm and should have a final joint width of approximately 3-10mm. Use :le spacers if desired to ensure even spacing.
WA Phone - (08) 9353 3354 VIC Phone - (03) 9763 4433 NSW Phone - (02) 9673 1322 [email protected]
5. Remove any surplus adhesive on face of the :le or between joints before it sets. 6. Adjustment of :les should be carried out within 15 minutes of laying (at 23°c and 50% rela:ve humidity) Coverage The coverage below is for 20kg of GSA FLOORFIX. Coverage will vary depending on the condi:on of the surface being :led and applica:on technique. As a general guide coverage will be 3.7m² using a 10mm notch trowel. Drying (me Full traffic should be possible a^er 24 hours (at 23°c and 50% rela:ve humidity). Allow longer for dense :les/substrates humid climates and low temperatures. Grou(ng Wait un:l adhesive has set firmly. This takes approximately 24 hours. Remove :le spaces and apply a suitable grout. Movement joints Movement joints must be in accordance with AS 3958.1:2077. As a general guide, movement joints should be incorporated at 4.5 metre intervals and around the perimeter of the floor. These joints must be approximately 6mm wide and kept free from adhesive and grout. Any structural movement joints must be carried through to the face of the :ling. They should be filled with a suitable flexible material such as GSA COLOURED SILICONE.
WA Phone - (08) 9353 3354 VIC Phone - (03) 9763 4433 NSW Phone - (02) 9673 1322 [email protected]
Shelf life A shelf life of 12 months is expected when stored in a dry place in iriginal unopened container at 30°c and 50% rela:ve humidity. Always re-seal bag air :ght a^er use. Packaging Product Code FFTA20 20kg bag 54 bags per pallet Cau(on Do not use in con:nuous immersed condi:ons such as swimming pools. Do not use over :mber floors. Do not use GSA FLOORFIX over concrete slabs subject to shrinkage and other movement. Use in conjunc:on with the GSA PRIMER AND ADDITIVE in exposed outdoor situa:ons by replacing all of the water in the mixing process. GSA guarantee Product is guaranteed for 10 years when installed to manufacturer’s instruc:ons. Manufactured under a quality system cer:fied as complying with ISO 9001 by an accredited cer:fied body. Technical details Characteris(cs of product: Colour and form: Grey powder Bulk Density 1.6kg/litre
WA Phone - (08) 9353 3354 VIC Phone - (03) 9763 4433 NSW Phone - (02) 9673 1322 [email protected]
Applica(on Proper(es (at 23°c and 50% rela(ve humidity) Mixing ra:o 100:23 (powder: water) Open :me: approx. 15 minutes Adjustability :me: approx. 25 minutes Sagging none Pot life 2 hours Mechanical Proper(es: AS4992.1 MEETS Sheer Bond Strength (Mpa): 7 days dry >1.0 Yes 14 days >1.5 Yes 28 days . 7 days water immersion >1.0 Yes Tensile Strength (Mpa) 7 days dry >0.15 Yes Safety Keep out of reach of children. Use gloves to prevent skin irrita:on. Avoid inhaling dust by using a dust mask. Wash immediately with plenty if water if material enters the eyes. Material Safety Data Sheet (MSDS) available in GSA website. Disclaimer Campbell Wholesale Pty Ltd believes that the informa:on in this technical data sheet is an accurate descrip:on of the typical uses of the product. The data and statements are based on our research and development work and is to the best of our knowledge true and accurate. The user must ensure of the product(s) in their applica:on prior to use in par:cular to determine its performance, efficiency and safety.
WA Phone - (08) 9353 3354 VIC Phone - (03) 9763 4433 NSW Phone - (02) 9673 1322 [email protected]
The use of this product is beyond the manufacturer’s control, and liability is restricted to the replacement of material proven faulty. The manufacturer is not responsible for any loss or damage arising from incorrect usage. Products conform solely to the informa:on contained in this and other related Campbells Wholesale Pty Ltd publica:ons. Campbells Wholesale Pty Ltd reserves the right to make changes to specifica:ons and informa:on related to the products at any :me. Users are asked to check that the literature in their possession is the latest issue. Statements contained herein should not be considered as a warranty of any kind, expressed or implied in describing the performance or suitability of the product for a par:cular applica:on. No liability is accepted for infringement of any patents or any other intellectual property right.
WA Phone - (08) 9353 3354 VIC Phone - (03) 9763 4433 NSW Phone - (02) 9673 1322 [email protected]
