Handspring Visor Deluxe PDA Motherboard and Memory card I/O ...
Handspring Visor Deluxe PDA Motherboard and Memory card I/O Replacement
Handspring Visor Deluxe PDA Motherboard and Memory card I/O Replacement How to install a new motherboard and memory card I/O into the Handspring Visor Deluxe PDA.
Written By: David Faltemier
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 8
Handspring Visor Deluxe PDA Motherboard and Memory card I/O Replacement
INTRODUCTION Use this guide to replace the Motherboard.
TOOLS: Phillips #00 Screwdriver (1) Spudger (1) Tweezers (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 8
Handspring Visor Deluxe PDA Motherboard and Memory card I/O Replacement
Step 1 — Outside cover and stylus
Remove the outer screen cover by releasing the top clip from the main body of the device.
Step 2
Pull out the stylus from the top right corner of the device.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 8
Handspring Visor Deluxe PDA Motherboard and Memory card I/O Replacement
Step 3
Slide the memory cartridge cover up and off the device.
Step 4 — Batteries
Remove the battery cover by releasing the clip from the main body of the device.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 8
Handspring Visor Deluxe PDA Motherboard and Memory card I/O Replacement
Step 5
Remove the batteries from the device.
Unscrew the four 2.94mm screws with a #00 Phillips screwdriver.
Step 6 — Back Cover
One end of the OEM stylus can unscrew and contains a mini #00 Phillips screwdriver.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 8
Handspring Visor Deluxe PDA Motherboard and Memory card I/O Replacement
Step 7
Use the spudger to pry open the casing by applying pressure at 4 clips on both sides of the device.
Be careful while opening the casing as there is a flex strip connecting the two halves. Step 8
Disconnect the flex strip from the motherboard with tweezers.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 8
Handspring Visor Deluxe PDA Motherboard and Memory card I/O Replacement
Step 9 — Button Pad and Battery Terminal
Use tweezers to remove the power button from the back case.
Step 10
Disconnect the button pad by using the spudger to pry it off the motherboard.
Remove the button pad.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 8
Handspring Visor Deluxe PDA Motherboard and Memory card I/O Replacement
Step 11 — Motherboard and Memory card I/O
Unscrew the two 2.94mm Phillips #00 screws that hold the motherboard in place.
Step 12
Use the spudger to lift the motherboard from the case.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-22 07:54:46 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 8 of 8
Handspring Visor Deluxe PDA Motherboard and Memory card I/O Replacement How to install a new motherboard and memory card I/O into the Handspring Visor Deluxe PDA.
Written By: David Faltemier
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 8
Handspring Visor Deluxe PDA Motherboard and Memory card I/O Replacement
INTRODUCTION Use this guide to replace the Motherboard.
TOOLS: Phillips #00 Screwdriver (1) Spudger (1) Tweezers (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 8
Handspring Visor Deluxe PDA Motherboard and Memory card I/O Replacement
Step 1 — Outside cover and stylus
Remove the outer screen cover by releasing the top clip from the main body of the device.
Step 2
Pull out the stylus from the top right corner of the device.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 8
Handspring Visor Deluxe PDA Motherboard and Memory card I/O Replacement
Step 3
Slide the memory cartridge cover up and off the device.
Step 4 — Batteries
Remove the battery cover by releasing the clip from the main body of the device.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 8
Handspring Visor Deluxe PDA Motherboard and Memory card I/O Replacement
Step 5
Remove the batteries from the device.
Unscrew the four 2.94mm screws with a #00 Phillips screwdriver.
Step 6 — Back Cover
One end of the OEM stylus can unscrew and contains a mini #00 Phillips screwdriver.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 8
Handspring Visor Deluxe PDA Motherboard and Memory card I/O Replacement
Step 7
Use the spudger to pry open the casing by applying pressure at 4 clips on both sides of the device.
Be careful while opening the casing as there is a flex strip connecting the two halves. Step 8
Disconnect the flex strip from the motherboard with tweezers.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 8
Handspring Visor Deluxe PDA Motherboard and Memory card I/O Replacement
Step 9 — Button Pad and Battery Terminal
Use tweezers to remove the power button from the back case.
Step 10
Disconnect the button pad by using the spudger to pry it off the motherboard.
Remove the button pad.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 8
Handspring Visor Deluxe PDA Motherboard and Memory card I/O Replacement
Step 11 — Motherboard and Memory card I/O
Unscrew the two 2.94mm Phillips #00 screws that hold the motherboard in place.
Step 12
Use the spudger to lift the motherboard from the case.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-22 07:54:46 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 8 of 8
