Installation Instructions - Displays2go
Installation Instructions Model:MD2002 Desktop Tilting TV Mount
Max Loading:15KG Screen Size:12” to 24”
Installation manual 1.We have the final ownership and interpretation for this Instruction. 2.Some detail in install maybe not in this instruction 3.Images may different from actual product
Note: 1.Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components 2.Do not begin the installation of the product when you have read and undetstand the instructions and warnings contained in this Installation sheet,if you have any question regarding any of the instruction or warning,please contact us. 3.Keep away from children 4.Never exceed the max loading.
Warranty period Two years after products deliver
-1-
Accessory
Connector A ×２
Pressure extending arm B ×２
Double-ended Converter E ×２
Adapter bracket C ×２
screw
Installation parts
-2-
Column D
Installing to Deak 1.make the size of tongs suitable for table’s thickness. 2.Put tongs to the right position,make sure it’s face to edge.revolve and fix the handle.
90mm
Note: Min.hole dlameter=10mm Max.hole dlameter=90mm
-3-
Hole Installation 1.Disassemble the desk clamp assembly to replace components for hole installation Retain three screws,rubber pad and clamp adjustment screw for later use as shown on 2-1
2-1
2.Re-install the base plate with three retained attach screws,tighten these screws with a 4mm allen key and paste the rubber pad on the one screw as shown on 2-2
2-2
3.From below desk,insert retained clamp adjustment through pad and up through hole in desk,Thread screw by turning the knob into base plate but not tighten completely at this time,Center the desk mount assembly over hole,securely tighten screw as shown on 2-3
note:Min.hole diameter = 10mm Max.hole diameter = 70mm
lamp adjustment screw 2-3
-4-
Installing the display 1.Make sure the bracket is hard to tip when you pull the head with your hand.you can use spanner to adjust it as shown on 3-1
-90˚
360˚ +90˚ 图:3-1
图:3-2
2.Put the display face down carefully, set out the hole deepness back of it,choose the right screw as shown on 3-3 Detail screen saver
图:3-3
Detail
screen saver
图:3-4
-5-
Installing adapter bracket 1.Put the double-ended Converter onto Column.then put the adapter bracket on converter as shown on 4-1 2.Lock the latch when the adapter bracket on the right position.fix it with spanner as shown on 4-2
Column
4-1
Detail
UP
Down 4-2
-6-
Cable management Note:Make sure that the adapter bracket can extend enough,cable are long and flab enough to moved. 1.Tighten the screw till the display angle can be fixed,then push or pull from top or bottom of screen to adjust the display to the desired angle. 2.Route the cables through the cable clip.
-7-
Adjusting the display monitor Warning:Forced movement of the articulated arms assembly or mount bracket without loosening the screws will damage articulated arms assembly or display monitor. 1.The MD2021 articulated arm design for 9KG loading. 2.To support display monitor when adjusting resistance of the articulated arm assembly 3.Referring to the weight of display monitor,it maybe required to make adjustments to the articulated arm assembly mechanism,if the display monitor doesn’t hold its position or is too resistant,adjust the M6*33mm Tension hex socket round head screw located on top of articulated arm using hex allen wrench 4mm,check the display monitor and the adjust again if it is necessary to make the adjustment.
-8-
Our products have nice design to make the display easier to the right position.
360˚
360˚
360˚ 360˚
-9-
Use the right distance and angle. Note:Proper ergonomic design is necessary to prevent repetitive strain injures which can develop over time and can lead to long-term disability. Keep the right distance from display to keep your eyes healthy,suggestion 460mm-610mm
- 10 -
We suggest to make the display lower 10-20 degrees to your vision.
distance
visio
n
make hand and desk on the same level keep the suitable seated position
angle of seated position angle of knuchle
height of chair
feet nature
- 11 -
Max Loading:15KG Screen Size:12” to 24”
Installation manual 1.We have the final ownership and interpretation for this Instruction. 2.Some detail in install maybe not in this instruction 3.Images may different from actual product
Note: 1.Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components 2.Do not begin the installation of the product when you have read and undetstand the instructions and warnings contained in this Installation sheet,if you have any question regarding any of the instruction or warning,please contact us. 3.Keep away from children 4.Never exceed the max loading.
Warranty period Two years after products deliver
-1-
Accessory
Connector A ×２
Pressure extending arm B ×２
Double-ended Converter E ×２
Adapter bracket C ×２
screw
Installation parts
-2-
Column D
Installing to Deak 1.make the size of tongs suitable for table’s thickness. 2.Put tongs to the right position,make sure it’s face to edge.revolve and fix the handle.
90mm
Note: Min.hole dlameter=10mm Max.hole dlameter=90mm
-3-
Hole Installation 1.Disassemble the desk clamp assembly to replace components for hole installation Retain three screws,rubber pad and clamp adjustment screw for later use as shown on 2-1
2-1
2.Re-install the base plate with three retained attach screws,tighten these screws with a 4mm allen key and paste the rubber pad on the one screw as shown on 2-2
2-2
3.From below desk,insert retained clamp adjustment through pad and up through hole in desk,Thread screw by turning the knob into base plate but not tighten completely at this time,Center the desk mount assembly over hole,securely tighten screw as shown on 2-3
note:Min.hole diameter = 10mm Max.hole diameter = 70mm
lamp adjustment screw 2-3
-4-
Installing the display 1.Make sure the bracket is hard to tip when you pull the head with your hand.you can use spanner to adjust it as shown on 3-1
-90˚
360˚ +90˚ 图:3-1
图:3-2
2.Put the display face down carefully, set out the hole deepness back of it,choose the right screw as shown on 3-3 Detail screen saver
图:3-3
Detail
screen saver
图:3-4
-5-
Installing adapter bracket 1.Put the double-ended Converter onto Column.then put the adapter bracket on converter as shown on 4-1 2.Lock the latch when the adapter bracket on the right position.fix it with spanner as shown on 4-2
Column
4-1
Detail
UP
Down 4-2
-6-
Cable management Note:Make sure that the adapter bracket can extend enough,cable are long and flab enough to moved. 1.Tighten the screw till the display angle can be fixed,then push or pull from top or bottom of screen to adjust the display to the desired angle. 2.Route the cables through the cable clip.
-7-
Adjusting the display monitor Warning:Forced movement of the articulated arms assembly or mount bracket without loosening the screws will damage articulated arms assembly or display monitor. 1.The MD2021 articulated arm design for 9KG loading. 2.To support display monitor when adjusting resistance of the articulated arm assembly 3.Referring to the weight of display monitor,it maybe required to make adjustments to the articulated arm assembly mechanism,if the display monitor doesn’t hold its position or is too resistant,adjust the M6*33mm Tension hex socket round head screw located on top of articulated arm using hex allen wrench 4mm,check the display monitor and the adjust again if it is necessary to make the adjustment.
-8-
Our products have nice design to make the display easier to the right position.
360˚
360˚
360˚ 360˚
-9-
Use the right distance and angle. Note:Proper ergonomic design is necessary to prevent repetitive strain injures which can develop over time and can lead to long-term disability. Keep the right distance from display to keep your eyes healthy,suggestion 460mm-610mm
- 10 -
We suggest to make the display lower 10-20 degrees to your vision.
distance
visio
n
make hand and desk on the same level keep the suitable seated position
angle of seated position angle of knuchle
height of chair
feet nature
- 11 -
