installation of sti-6517 sti stopper® station shield
STOPPER STATION SHEILD SHIELD PIVOT
Safety Technology International, Inc.
Safety Technology International (Europe) Ltd.
2306 Airport Road • Waterford, Michigan 48327-1209 Phone: 248-673-9898 • Fax: 248-673-1246 Toll Free: 800-888-4784 • E-mail: [email protected] Web: www.sti-usa.com
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch Worcestershire •BUTTON B98 0HU • England • Tel: 44MOUNTING (0) 1527SLOTS 520 999 COVER LEVER PCB GUIDE Fax: 44 (0) 1527 501 999 • Freephone: 0800 085 1678 (UK only) E-mail: [email protected] • Web: www.sti-europe.com 123A LITHIUM BATTERY SOUNDER PCB STOPPER STATION SHEILD SHIELD PIVOT
STOPPER STATION SHELL WITH NOTCHED SLOTS (FOR SHIELD PIVOTS)
STOPPER STATION SHIELD
COVER MOUNTING SLOTS PCB GUIDE
BUTTON LEVER
123A LITHIUM BATTERY SOUNDER PCB
STOPPER STATION CONTACT ASSEMBLY
STOPPER STATION SHELL WITH NOTCHED SLOTS (FOR SHIELD PIVOTS)
STOPPER STATION SHIELD
STOPPER STATION COVER
STOPPER STATION CONTACT ASSEMBLY
STOPPER STATION CONTACT ASSEMBLY SCREW
STOPPER STATION SHELL STOPPER STATION COVER
SCREW
INSTALLATION NOTES STOPPER STATION SHELL
5.32 in. (135mm)
4.84 in. (123mm)
3.51 in. (89mm)
1.76 in. (45mm)
STOPPER STATION CONTACT ASSEMBLY
1. Insert Sounder/Wireless PCB into PCB Card Guides on Stopper Station Cover. 2. Orient the Button Lever so it is pointed toward the inside of the Stopper Station Shield Assembly. 3. With Shield Rotated to open position (Approximately 90° to Cover), insert Shield Pivots into Slots on Stopper Station Cover. 4. Rotate Cover to Closed Position. 5. Rotate Cover to fully open position, back to closed position, and ensure the Button Level is pressed down onto the button. If not, repeat steps 2-5. 6. Program the sounder volume on or off by pulling off the plastic battery tab with the battery remaining installed. (Sounder will be on at this point) 7. The sounder volume programming cycle is ON for 10 seconds, OFF for 10 seconds, and then defaults to ON. To set volume: open the Shield, close, open again and close again. NOTE: Remove and replace battery to reset volume setting. 8. Mount Shield, Cover and PCB Assembly onto Stopper Station Button Assembly. 9. Install Screw to Hold Cover to Button Assembly.
Electronic warranty form at www.sti-usa.com/wc14
INSTALLATION OF STI-6517 STI STOPPER® STATION SHIELD
STATION SHEILD All specifications and information shown were current as of publication andSTOPPER are subject to change without notice. SHIELD PIVOT
6517 MARCH2010
Safety Technology International, Inc.
Safety Technology International (Europe) Ltd.
2306 Airport Road • Waterford, Michigan 48327-1209 Phone: 248-673-9898 • Fax: 248-673-1246 Toll Free: 800-888-4784 • E-mail: [email protected] Web: www.sti-usa.com
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch Worcestershire •BUTTON B98 0HU • England • Tel: 44MOUNTING (0) 1527SLOTS 520 999 COVER LEVER PCB GUIDE Fax: 44 (0) 1527 501 999 • Freephone: 0800 085 1678 (UK only) E-mail: [email protected] • Web: www.sti-europe.com 123A LITHIUM BATTERY SOUNDER PCB STOPPER STATION SHEILD SHIELD PIVOT
STOPPER STATION SHELL WITH NOTCHED SLOTS (FOR SHIELD PIVOTS)
STOPPER STATION SHIELD
COVER MOUNTING SLOTS PCB GUIDE
BUTTON LEVER
123A LITHIUM BATTERY SOUNDER PCB
STOPPER STATION CONTACT ASSEMBLY
STOPPER STATION SHELL WITH NOTCHED SLOTS (FOR SHIELD PIVOTS)
STOPPER STATION SHIELD
STOPPER STATION COVER
STOPPER STATION CONTACT ASSEMBLY
STOPPER STATION CONTACT ASSEMBLY SCREW
STOPPER STATION SHELL STOPPER STATION COVER
SCREW
INSTALLATION NOTES STOPPER STATION SHELL
5.32 in. (135mm)
4.84 in. (123mm)
3.51 in. (89mm)
1.76 in. (45mm)
STOPPER STATION CONTACT ASSEMBLY
1. Insert Sounder/Wireless PCB into PCB Card Guides on Stopper Station Cover. 2. Orient the Button Lever so it is pointed toward the inside of the Stopper Station Shield Assembly. 3. With Shield Rotated to open position (Approximately 90° to Cover), insert Shield Pivots into Slots on Stopper Station Cover. 4. Rotate Cover to Closed Position. 5. Rotate Cover to fully open position, back to closed position, and ensure the Button Level is pressed down onto the button. If not, repeat steps 2-5. 6. Program the sounder volume on or off by pulling off the plastic battery tab with the battery remaining installed. (Sounder will be on at this point) 7. The sounder volume programming cycle is ON for 10 seconds, OFF for 10 seconds, and then defaults to ON. To set volume: open the Shield, close, open again and close again. NOTE: Remove and replace battery to reset volume setting. 8. Mount Shield, Cover and PCB Assembly onto Stopper Station Button Assembly. 9. Install Screw to Hold Cover to Button Assembly.
Electronic warranty form at www.sti-usa.com/wc14
INSTALLATION OF STI-6517 STI STOPPER® STATION SHIELD
STATION SHEILD All specifications and information shown were current as of publication andSTOPPER are subject to change without notice. SHIELD PIVOT
6517 MARCH2010
