MULTI-ACTIVITY PLAY TABLE
MULTI-ACTIVITY PLAY TABLE ASSEMBLY INSTRUCTIONS
!
WARNING:
CHOKING HAZARD - Small parts. Not for children under 3 years.
!
CAUTION:
Adult assembly required.
ITEM #2371 C
©2006
Melissa and Doug, Inc. All Rights Reserved www.MelissaAndDoug.com
We care about your comments. Please call us! 1-800-284-3948
MULTI-ACTIVITY PLAY TABLE How to correctly install Barrel Nuts Press a Barrel Nut into the hole in the part making sure that the "+" pattern is facing out. Properly aligned Barrel Nut.
"+" pattern
The Barrel Nut may look like this - which is not straight with the hole at the edge for the Hex Screw. ITEM #2371
Hole for Hex Screw
Using a standard screwdriver, turn the Nut until the "+" is straight so that the threaded hole is facing outward to accept the Hex Screw. Page 2 of 15
MULTI-ACTIVITY PLAY TABLE PARTS LIST 1
3
1 pc
4 1 pc
1 pc
2 2 pcs
5
6
2 pcs
9
7 10
2 pcs
1 pc
8
1 pc
11
14
1 pc
12
2 pcs
2 pcs
13 1 pc 1 pc
Barrel Nut 16 pcs
2 pcs
Hex Key 1 pc
ITEM #2371 Page 3 of 15
Cap Nut
8 pcs
Short Hex Screw 8 pcs
Long Hex Screw 16 pcs
Short Wood Screw 2 pcs
Long Wood Screw 6 pcs
STEP 1
MULTI-ACTIVITY PLAY TABLE Assemble the sides of the drawer, part #2 to the back, #1 using 4 long hex screws and 4 barrel nuts.
1
2
grooves
3
Next, slide part #3 into the grooves as shown making sure that it slides fully into the groove in panel #1. Make sure that all "grooves" are facing the inside of the drawer as shown.
2 Fasteners used in this step
Assembled View
Full Size
4 Barrel Nuts
4 Long Hex Screws
Hex Screw
Barrel Nut
ITEM #2371 Page 4 of 15
Check when done
STEP 2
MULTI-ACTIVITY PLAY TABLE Attach the drawer front, #4 using 4 long hex screws and 4 barrel nuts. Set the drawer aside for later assembly in the table. Barrel Nut
Hex Screw
4
Fasteners used in this step Full Size
4 Barrel Nuts
4 Long Hex Screws Assembled View
Check when done
ITEM #2371 Page 5 of 15
STEP 3
MULTI-ACTIVITY PLAY TABLE Attach end supports #6 to both end panels #5 as shown using 4 short hex screws and 4 cap nuts.
5
6
Hex Screw goes on the outside
6
Cap Nuts are on the inside
5 Fasteners used in this step Full Size
4 Cap Nuts
4 Short Hex Screws Assembled View
ITEM #2371 Page 6 of 15
Check when done
MULTI-ACTIVITY PLAY TABLE STEP 4
Attach supports #9 to the rear panel #8 and the front panel #7 as shown using 4 short hex screws and 4 cap nuts. Make sure these large holes are facing inward on both parts of the front and rear panels.
8 9
Hex Screws on the outside
Cap Nut goes here on the inside
7 Fasteners used in this step Full Size
4 Cap Nuts
4 Short Hex Screws
Assembled View
ITEM #2371 Page 7 of 15
Check when done
STEP 5
MULTI-ACTIVITY PLAY TABLE Attach part #10 to the inside of the front panel as shown using 2 short wood screws. Do not over-tighten the screws!
10 Fasteners used in this step Full Size
2 Short Wood Screws
Assembled View
Check when done
ITEM #2371 Page 8 of 15
STEP 6
MULTI-ACTIVITY PLAY TABLE Now attach the end panel assemblies #5 to the rear panel #8 using 4 long hex screws and 4 barrel nuts.
8
5 5
Fasteners used in this step Full Size
4 Barrel Nuts
4 Long Hex Screws
Assembled View
Check when done
ITEM #2371 Page 9 of 15
STEP 7
MULTI-ACTIVITY PLAY TABLE Attach the front panel #7 to the rest of the table assembly, between the end panels, using 4 long hex screws and 4 barrel nuts.
7
Fasteners used in this step Full Size
Assembled View 4 Barrel Nuts
4 Long Hex Screws
Check when done
ITEM #2371 Page 10 of 15
STEP 8
MULTI-ACTIVITY PLAY TABLE Attach the table supports #11 into the slots as shown and secure with 4 long wood screws.
11
Fasteners used in this step Full Size
4 Long Wood Screws
Assembled View
ITEM #2371 Page 11 of 15
Check when done
STEP 9
MULTI-ACTIVITY PLAY TABLE Start with the drawer inside the 2 top supports and then fit it into the front opening by carefully guiding the drawer pull over the stabilizer strip.
stabilizer strip
Move the drawer to almost completely open, being careful as it will tend to tip forward a bit. In the next step you may need to move the drawer back and forth to fit the dowel in place.
Check when done
ITEM #2371 Page 12 of 15
STEP 10
MULTI-ACTIVITY PLAY TABLE Insert the wood dowel #12 through the hole in the back of the drawer as shown and let it rest in the front hole in the support.
12 Dowel slides through rear of drawer and into the hole in the front support
Check when done
ITEM #2371 Page 13 of 15
STEP 11
MULTI-ACTIVITY PLAY TABLE 13
Fit part #13 to the end of the dowel by lifting the dowel and drawer and then fit it into the slots as shown. Attach using 2 long wood screws. Make sure that the drawer is free to slide in and out.
Fasteners used in this step Full Size
2 Long Wood Screws
Assembled View
Check when done
ITEM #2371 Page 14 of 15
STEP 12 14
MULTI-ACTIVITY PLAY TABLE Place 2 top surfaces #14 on top of the table and you are ready to play!
Assembled View
Check when done
ITEM #2371 Page 15 of 15
!
WARNING:
CHOKING HAZARD - Small parts. Not for children under 3 years.
!
CAUTION:
Adult assembly required.
ITEM #2371 C
©2006
Melissa and Doug, Inc. All Rights Reserved www.MelissaAndDoug.com
We care about your comments. Please call us! 1-800-284-3948
MULTI-ACTIVITY PLAY TABLE How to correctly install Barrel Nuts Press a Barrel Nut into the hole in the part making sure that the "+" pattern is facing out. Properly aligned Barrel Nut.
"+" pattern
The Barrel Nut may look like this - which is not straight with the hole at the edge for the Hex Screw. ITEM #2371
Hole for Hex Screw
Using a standard screwdriver, turn the Nut until the "+" is straight so that the threaded hole is facing outward to accept the Hex Screw. Page 2 of 15
MULTI-ACTIVITY PLAY TABLE PARTS LIST 1
3
1 pc
4 1 pc
1 pc
2 2 pcs
5
6
2 pcs
9
7 10
2 pcs
1 pc
8
1 pc
11
14
1 pc
12
2 pcs
2 pcs
13 1 pc 1 pc
Barrel Nut 16 pcs
2 pcs
Hex Key 1 pc
ITEM #2371 Page 3 of 15
Cap Nut
8 pcs
Short Hex Screw 8 pcs
Long Hex Screw 16 pcs
Short Wood Screw 2 pcs
Long Wood Screw 6 pcs
STEP 1
MULTI-ACTIVITY PLAY TABLE Assemble the sides of the drawer, part #2 to the back, #1 using 4 long hex screws and 4 barrel nuts.
1
2
grooves
3
Next, slide part #3 into the grooves as shown making sure that it slides fully into the groove in panel #1. Make sure that all "grooves" are facing the inside of the drawer as shown.
2 Fasteners used in this step
Assembled View
Full Size
4 Barrel Nuts
4 Long Hex Screws
Hex Screw
Barrel Nut
ITEM #2371 Page 4 of 15
Check when done
STEP 2
MULTI-ACTIVITY PLAY TABLE Attach the drawer front, #4 using 4 long hex screws and 4 barrel nuts. Set the drawer aside for later assembly in the table. Barrel Nut
Hex Screw
4
Fasteners used in this step Full Size
4 Barrel Nuts
4 Long Hex Screws Assembled View
Check when done
ITEM #2371 Page 5 of 15
STEP 3
MULTI-ACTIVITY PLAY TABLE Attach end supports #6 to both end panels #5 as shown using 4 short hex screws and 4 cap nuts.
5
6
Hex Screw goes on the outside
6
Cap Nuts are on the inside
5 Fasteners used in this step Full Size
4 Cap Nuts
4 Short Hex Screws Assembled View
ITEM #2371 Page 6 of 15
Check when done
MULTI-ACTIVITY PLAY TABLE STEP 4
Attach supports #9 to the rear panel #8 and the front panel #7 as shown using 4 short hex screws and 4 cap nuts. Make sure these large holes are facing inward on both parts of the front and rear panels.
8 9
Hex Screws on the outside
Cap Nut goes here on the inside
7 Fasteners used in this step Full Size
4 Cap Nuts
4 Short Hex Screws
Assembled View
ITEM #2371 Page 7 of 15
Check when done
STEP 5
MULTI-ACTIVITY PLAY TABLE Attach part #10 to the inside of the front panel as shown using 2 short wood screws. Do not over-tighten the screws!
10 Fasteners used in this step Full Size
2 Short Wood Screws
Assembled View
Check when done
ITEM #2371 Page 8 of 15
STEP 6
MULTI-ACTIVITY PLAY TABLE Now attach the end panel assemblies #5 to the rear panel #8 using 4 long hex screws and 4 barrel nuts.
8
5 5
Fasteners used in this step Full Size
4 Barrel Nuts
4 Long Hex Screws
Assembled View
Check when done
ITEM #2371 Page 9 of 15
STEP 7
MULTI-ACTIVITY PLAY TABLE Attach the front panel #7 to the rest of the table assembly, between the end panels, using 4 long hex screws and 4 barrel nuts.
7
Fasteners used in this step Full Size
Assembled View 4 Barrel Nuts
4 Long Hex Screws
Check when done
ITEM #2371 Page 10 of 15
STEP 8
MULTI-ACTIVITY PLAY TABLE Attach the table supports #11 into the slots as shown and secure with 4 long wood screws.
11
Fasteners used in this step Full Size
4 Long Wood Screws
Assembled View
ITEM #2371 Page 11 of 15
Check when done
STEP 9
MULTI-ACTIVITY PLAY TABLE Start with the drawer inside the 2 top supports and then fit it into the front opening by carefully guiding the drawer pull over the stabilizer strip.
stabilizer strip
Move the drawer to almost completely open, being careful as it will tend to tip forward a bit. In the next step you may need to move the drawer back and forth to fit the dowel in place.
Check when done
ITEM #2371 Page 12 of 15
STEP 10
MULTI-ACTIVITY PLAY TABLE Insert the wood dowel #12 through the hole in the back of the drawer as shown and let it rest in the front hole in the support.
12 Dowel slides through rear of drawer and into the hole in the front support
Check when done
ITEM #2371 Page 13 of 15
STEP 11
MULTI-ACTIVITY PLAY TABLE 13
Fit part #13 to the end of the dowel by lifting the dowel and drawer and then fit it into the slots as shown. Attach using 2 long wood screws. Make sure that the drawer is free to slide in and out.
Fasteners used in this step Full Size
2 Long Wood Screws
Assembled View
Check when done
ITEM #2371 Page 14 of 15
STEP 12 14
MULTI-ACTIVITY PLAY TABLE Place 2 top surfaces #14 on top of the table and you are ready to play!
Assembled View
Check when done
ITEM #2371 Page 15 of 15
