Savant Select Charging Base (SSB-1000) Quick Reference Guide
Savant Select Charging Base (SSB-1000) Quick Reference Guide
009-0874-00 SSB-1000
The Savant Select Charging Base (SSB-1000) Quick Reference Guide provides information to install the SSB-1000 power adaptor and charge the lithium ion battery on the Savant Select Remote (SSR-1000).
Box Contents (1) SSB-1000 Charging Base (1) 5V DC 2.5 Amps Universal Wall Unit (1) Quick Reference Guide (this document)
Rear View of Charging Base
Charging Base Power Adaptor Installation To install 5V adaptor with 1 meter power cord (2, 3 and 4), do the following: 4. At the rear of the Charging Base (1), select the path you want to use to install the power cord. NOTE: Savant recommends installing the jack (2) first and then routing the power cord (3). 5. If you choose to route the power cord (3) in the channel as shown below, press the power cord between the retainers in the channel. 6. After routing the power cord, select and snap in the “power clip” for the specific region into the power adaptor and plug the adaptor (4) into a 100-240 volt, 50/60 Hz surge protected outlet.
Top View of Charging Base
Specifications Environmental Operating Temperature
32º to 95º F (0º to 35º C)
Non-operating Temperature
32º to 113º F (0º to 45º C)
Operating Humidity
5% to 95% Non-condensing
Dimensions and Weight Measurements
9 in x 2.6 in x 0.55 in (22.86 cm x 6.60 cm x 1.40 cm)
Weight
3 oz/0.40 kg (shipping weight)
Power Input
5V DC, 2.5 Amp Adaptor with 1 m cord
Regulatory Safety and Emissions
FCC Part 15 | CE Mark | C-Tick
RoHS
Compliant
*NOTE: For first time use, the battery must be charged for a minimum of eight hours before using the remote.
SSR-1000 Remote with Charging Base
Battery Installation
Charging the Battery NOTE: For first time use, the battery must be charged for a minimum of eight hours before using the remote. To charge the lithium ion battery, do the following: Base (SSB-1000) Install into aControl 100-240 50/60 Hz surge protected outlet using Modules the supplied 100-240V AC, 50/60 Hz to 5V DC adaptor. 4. Write down the numbers of the loads (shown on the Enclosure 2. Place the SSR-1000 onto the charging base as shown. Schedule in the “DWG #” column) to be attached to each module. TheLED illustration abovefront shows of the the labeling strip. Load num3. Locate the Status on the SSR-1000. The following table describes the bers should also be labeled on the load homeruns. status.
Plug the Charging Install 1. Savant Components
It is easiest if you install all modules before beginning the wiring, explained in the next section.
!"#$%&"'$ Status LEDs ()*+,-$
Green indicates the remote is fully charged and docked. Orange indicates remote is charging. Red indicates the remote is not docked and battery is low and needs charging. Off indicates the remote is not docked or the battery is dead. There is a barrier in each enclosure that isolates voltage Flashing Red indicates thatline one of from the remote buttons was pressed, but low voltage. DO NOT cross over the or through barrier withwas any in the sleep mode or not in the ignored because iPodthistouch® wires. Keep low voltage wires on the low-voltage side and line II appside. mode. voltageTrueControl wires on the line-voltage All low and line voltage
Note the following cautions and warnings before wiring the load homeruns and the line voltage breaker lines to the modules:
lines must maintain a minimum distance of six inches. Before connecting load homeruns to modules, verify that there are no shorts in the load runs. ./01234 When using low voltage transformer loads, make sure the lamps are installed before connecting them to the outputs of the dimmer modules. The unloaded transformers can induce a voltage back Lithium-ion ( Li-ion) contain chemicals thatasare harmful to the environment. to the batteries dimmer and damage the module components well as the transformer. old battery according to local and state codes at a designated site in your area. Do not place more than one module on a breaker. All neutral feeds associated with a module must be connected to that module’s neutral bar, including the neutral from the breaker.
Lithium-ion (Li-ion) Battery Disposal (Recycle)
!/54246
To install the BAT-0001 battery: 1. Locate the battery cover on the rear of the Savant Select Remote. 2. Push the latch down and pull the cover out to remove. 3. Install the battery Ensure the battery contacts are positioned as shown. Ensure the battery pull-tab is accessible in the event you must remove the battery. 4. Position the two tabs on the cover into the lower section and press cover in until latch clicks to secure the cover. For more information, go to : dealers.SavantSystems.com Knowledge Base > Savant Hardware > Remotes > Savant Select
Additional Documentation Additional Documentation is available at: dealers.SavantSystems.com Knowledge Base > Savant Hardware > Remotes > Savant Select > BAT-0001
Recycle the
Turn off power to modules before connecting load homeruns or installing/servicing fixtures. When powered on, dimmer modules have “triac leakage voltage,” which allows some power into any connected load homeruns until the fixtures are installed.
the following to connect load homeruns to modules.and RacePoint Blueprint are trademarks of Savant Systems, LLC. Copyright © 2013 Do Savant Systems, LLC. SAVANT All brand names, product trademarks arevoltage the property of totheir respective owners. 1. Identifynames the loadand homeruns and the line breaker line bereserves attached tothe eachright module. Savant Systems, LLC to change product specifications without notice.
2. All modules that control line voltage loads require one line voltage run from a breaker, and each module should receive power from a separate breaker. Run the line voltage runs for the modules into each enclosure. Refer to Appendix C, “Drawings” on page 207 for detailed drawings showing the wiring routing and various module connections.
!"#"$%&!'"(%)*+,%*$+&-./012'.$%&34*5.&
67
030513
009-0874-00 SSB-1000
The Savant Select Charging Base (SSB-1000) Quick Reference Guide provides information to install the SSB-1000 power adaptor and charge the lithium ion battery on the Savant Select Remote (SSR-1000).
Box Contents (1) SSB-1000 Charging Base (1) 5V DC 2.5 Amps Universal Wall Unit (1) Quick Reference Guide (this document)
Rear View of Charging Base
Charging Base Power Adaptor Installation To install 5V adaptor with 1 meter power cord (2, 3 and 4), do the following: 4. At the rear of the Charging Base (1), select the path you want to use to install the power cord. NOTE: Savant recommends installing the jack (2) first and then routing the power cord (3). 5. If you choose to route the power cord (3) in the channel as shown below, press the power cord between the retainers in the channel. 6. After routing the power cord, select and snap in the “power clip” for the specific region into the power adaptor and plug the adaptor (4) into a 100-240 volt, 50/60 Hz surge protected outlet.
Top View of Charging Base
Specifications Environmental Operating Temperature
32º to 95º F (0º to 35º C)
Non-operating Temperature
32º to 113º F (0º to 45º C)
Operating Humidity
5% to 95% Non-condensing
Dimensions and Weight Measurements
9 in x 2.6 in x 0.55 in (22.86 cm x 6.60 cm x 1.40 cm)
Weight
3 oz/0.40 kg (shipping weight)
Power Input
5V DC, 2.5 Amp Adaptor with 1 m cord
Regulatory Safety and Emissions
FCC Part 15 | CE Mark | C-Tick
RoHS
Compliant
*NOTE: For first time use, the battery must be charged for a minimum of eight hours before using the remote.
SSR-1000 Remote with Charging Base
Battery Installation
Charging the Battery NOTE: For first time use, the battery must be charged for a minimum of eight hours before using the remote. To charge the lithium ion battery, do the following: Base (SSB-1000) Install into aControl 100-240 50/60 Hz surge protected outlet using Modules the supplied 100-240V AC, 50/60 Hz to 5V DC adaptor. 4. Write down the numbers of the loads (shown on the Enclosure 2. Place the SSR-1000 onto the charging base as shown. Schedule in the “DWG #” column) to be attached to each module. TheLED illustration abovefront shows of the the labeling strip. Load num3. Locate the Status on the SSR-1000. The following table describes the bers should also be labeled on the load homeruns. status.
Plug the Charging Install 1. Savant Components
It is easiest if you install all modules before beginning the wiring, explained in the next section.
!"#$%&"'$ Status LEDs ()*+,-$
Green indicates the remote is fully charged and docked. Orange indicates remote is charging. Red indicates the remote is not docked and battery is low and needs charging. Off indicates the remote is not docked or the battery is dead. There is a barrier in each enclosure that isolates voltage Flashing Red indicates thatline one of from the remote buttons was pressed, but low voltage. DO NOT cross over the or through barrier withwas any in the sleep mode or not in the ignored because iPodthistouch® wires. Keep low voltage wires on the low-voltage side and line II appside. mode. voltageTrueControl wires on the line-voltage All low and line voltage
Note the following cautions and warnings before wiring the load homeruns and the line voltage breaker lines to the modules:
lines must maintain a minimum distance of six inches. Before connecting load homeruns to modules, verify that there are no shorts in the load runs. ./01234 When using low voltage transformer loads, make sure the lamps are installed before connecting them to the outputs of the dimmer modules. The unloaded transformers can induce a voltage back Lithium-ion ( Li-ion) contain chemicals thatasare harmful to the environment. to the batteries dimmer and damage the module components well as the transformer. old battery according to local and state codes at a designated site in your area. Do not place more than one module on a breaker. All neutral feeds associated with a module must be connected to that module’s neutral bar, including the neutral from the breaker.
Lithium-ion (Li-ion) Battery Disposal (Recycle)
!/54246
To install the BAT-0001 battery: 1. Locate the battery cover on the rear of the Savant Select Remote. 2. Push the latch down and pull the cover out to remove. 3. Install the battery Ensure the battery contacts are positioned as shown. Ensure the battery pull-tab is accessible in the event you must remove the battery. 4. Position the two tabs on the cover into the lower section and press cover in until latch clicks to secure the cover. For more information, go to : dealers.SavantSystems.com Knowledge Base > Savant Hardware > Remotes > Savant Select
Additional Documentation Additional Documentation is available at: dealers.SavantSystems.com Knowledge Base > Savant Hardware > Remotes > Savant Select > BAT-0001
Recycle the
Turn off power to modules before connecting load homeruns or installing/servicing fixtures. When powered on, dimmer modules have “triac leakage voltage,” which allows some power into any connected load homeruns until the fixtures are installed.
the following to connect load homeruns to modules.and RacePoint Blueprint are trademarks of Savant Systems, LLC. Copyright © 2013 Do Savant Systems, LLC. SAVANT All brand names, product trademarks arevoltage the property of totheir respective owners. 1. Identifynames the loadand homeruns and the line breaker line bereserves attached tothe eachright module. Savant Systems, LLC to change product specifications without notice.
2. All modules that control line voltage loads require one line voltage run from a breaker, and each module should receive power from a separate breaker. Run the line voltage runs for the modules into each enclosure. Refer to Appendix C, “Drawings” on page 207 for detailed drawings showing the wiring routing and various module connections.
!"#"$%&!'"(%)*+,%*$+&-./012'.$%&34*5.&
67
030513
