TriFold Wallet 6x10 Hoop
Click the logo above to be taken to our web site. Join us on
TriFold Wallet 6x10 Hoop
Our ‘In the Hoop Trifold Wallet’ is made completely in your hoop, has slots for 4 credit cards and a fully lined zippered pocket for change, etc. It folds neatly and secures with a snap. The flap, inside zippered pocket and outside of the wallet are stippled quilted.
~~~~~ Note: Designer SE users make sure you’re using the 150x240 files 2 fabrics were used in our sample. Fabric 1 (main fabric ~ cream/gray/teal) was used for the outside and inside pieces. Fabric 2 (gray dot) was used for the credit card pockets and the lining for the zippered pocket. This design is not suited for directional fabric. We use spray (lightly) to secure all pieces unless noted otherwise. READ THROUGH INSTRUCTIONS BEFORE BEGINNING The fabric pieces needed will be referred to by letters A ~ M These pieces are listed under Supplies Needed below in the order they are used in the design.
1
If you want to add an optional fabric loop to attach hardware and a strap, make the loop before starting. When flat it should be 3” long. Width depends on the hardware you’re using. The quilted flap and outside of the wallet has to be stitched first. Do not stitch the last step of this design. It is an X in the lower right corner. This step is here to keep the machine foot from returning to the center and possibly hitting the zipper pull.
Supplies Needed: Flap:
*1 piece of Warm & Natural thin cotton batting 6” x 8” A *2 pieces of fabric 1, 6”w x 8”h B, C
Quilted Outside of Wallet
*1 piece of Warm & Natural thin cotton batting 7.50” x 11.50” D *1 piece of fabric 1, 7.50” x 11.50” E
Wallet:
*1 piece of fabric 1, 7.50”w x 6”h F *2 pieces of fabric 2 (credit card pockets) 7.50”w x 7”h ~ Fold both pieces wrong sides together to measure 7.50”w x 3.50”h G, H *1 piece of fabric 1, 7.50”w x 2.50”h I ~ Fold the bottom long edge of this piece under ½”. Be sure to measure. After folding under, press. A photo is below in the instructions of this piece. *2 piece of fabric 2, 7.50”w x 5”h J, K *1 piece of fabric 1, 7.50”w x 5”h L *1 piece of Warm & Natural thin cotton batting 7.50” x 4.50” M *1 Zipper 9”. No metal teeth. The zipper can be longer. *1 snap set size 20 – We use KamSnaps www.kamsnaps.com
~~~~~ Pay attention to the photos in the instructions. Have your hoop orientated as shown.
Make the Flap Hoop poly mesh stabilizer (soft cutaway) in a 5x7 hoop. Place warm & natural piece A centered in your hoop. Place fabric B, right side up over the warm & natural.
2
1.Stipple quilting Place fabric piece C, right side down on top of B.
2.This step stitches the flap together. Remove the flap from the hoop. Trim around the flap ¼” from the stitching on all sides. Clip the corners diagonally. Turn the flap to the right side. Push out the corners nicely. Press. Machine baste the raw edges together close to the edge. Set the flap aside.
Make the Quilted Outside Hoop poly mesh stabilizer (soft cutaway) in a 6x10 hoop Place warm & natural piece D centered in your hoop. Place fabric E, right side up over the warm & natural. 1.Stipple Remove piece from the hoop. Trim stabilizer away. Set this piece aside.
3
Make the Wallet Hoop poly mesh stabilizer (soft cutaway) in a 6x10 hoop 1.Stitch this step onto the stabilizer only. It’s a placement line.
Place piece F right side up, with one 7.50” edge even with the placement line.
2.This step stitches a placement line for the flap that will be used later.
4
Measure down .75” from the flap placement line and place pocket piece G as shown below. Tape the pocket in place along the fold.
Stitch step 3. This step secures the pocket at the bottom of the pocket. Place pocket piece H with the raw edges even with the bottom of piece F As shown below. Tape the pocket in place.
5
Stitch step 4. This step stitches the dividing lines in the credit card pockets.
Stitch step 5. This step stitches the placement lines for the zipper. Place the zipper, right side up, with the pull on the left centered between the placement lines. The pull and the stop will be out of the hoop. Tape the zipper in place.
6
Stitch step 6. This step will stitch the zipper in place.
Next you will place piece I. This is the piece that has the ½” edge folded under.
7
Place piece I, right side down with the unfolded edge even with the bottom of pocket piece H.
Stitch step 7. This step stitches piece I on. Fold I down so that the fold is even with the top edge of the teeth of the zipper. Press the seam.
Close up of I pressed down and aligned with the top edge of the zipper teeth.
8
Turn the hoop to the back side. Place piece J right side down with one 7.50” edge even with the top edge of the zipper tape. Secure this edge in place.
Turn the hoop to the front side. Tape I in place with the fold even with the top of the zipper teeth. Stitch step 8. This step stitches I & J to the zipper.
9
Stitch step 9. This step stitches a decorative stitch across piece I.
Turn the hoop to the back side. Fold piece J up and tape it in place. Do not use spray.
10
Place piece K right side down with one 7.50” edge even with the bottom edge of the zipper tape. Secure the edge in place.
Turn the hoop to the front side. Place piece L right side down with one 7.50” even with the bottom edge of the zipper tape. Secure the edge in place.
Stitch step 10. This step stitches pieces K & L to the zipper. Place the warm & natural piece M with one 7.50” edge even with the seam just sewn.
11
Fold piece L down over the warm & natural. Use spray to secure.
Stitch step 11. This step stitches the stipple quilting on the pocket. Turn the hoop to the back side. Fold piece K down and secure. Carefully trim the stabilizer from the zipper. It’s easier to do it now than later.
12
Fold piece J down. Tape in place.
Stitch step 12. This step stitches a line near the bottom of the hoop as shown in the photo below.
13
Unzip the zipper half way as shown by the black arrow in the photo below.
*Optional: If you want to add a loop to add hardware and a strap, add it now. Make a 3” fabric strap. Fold the strap in half. Place the strap on the front side of the hoop on the LEFT hand side as shown below. Have the fold of the loop about 1/4” past the credit card slot stitching. Have the loop edge even with the top of the second pocket. Tape in place. Note: We’re adding our hardware at this time too.
14
Place the flap, right side up (the side with the stipple) even with the flap placement line at the top of the hoop. Mark sure the flap is centered. Tape the flap in place.
Place the quilted outside you created first, right side down centered on top of the hoop. Pin in place through all layers out of the way of the foot.
15
Stitch step 13. This step stitches the wallet together. The design is finished. Remove the hoop from the machine. Do not stitch the ‘X’. Trim around the design ¼” from the stitching except at the bottom leave ½”. If you added the fabric loop, do not cut the ends off. Clip corners diagonally.
Trim the excess layers from the opening. Leave the pieces that form the opening. Turn the wallet to the right side. Push out the sides and corners nicely. Turn the raw edges at the bottom in. Press the wallet.
16
Time to install the snap. The male snap will be installed on the flap The male part of the snap will be on the inside. Center the snap on the flap about ¼” up from the edge.
Place credit cards into the slots. You are doing this to determine the placement for the female snap. Fold the wallet in half. Make sure the turned in edges are even.
Fold the flap down. Mark where the snap needs to go.
17
The female snap will be installed from the inside of the wallet. The female part of the snap will be on the outside of the wallet.
Make sure the folded in edges at the opening are even. Using a ladder stitch (you can google for it) close the opening. The ladder stitch is easy to do and makes an almost invisible closing.
©Embroidery Garden LLC LEGAL NOTICE, ALL RIGHTS RESERVED All of my designs are Copyrighted and treated as software. Purchase of designs from Embroidery Garden is a license to use the designs. Any form of sharing, loaning, copying, duplicating, re-selling or any other transfer of my designs, whether purchased or a free design, is strictly prohibited. You can combine my design with other designs and/ or fonts. You CAN NOT take my designs apart and use any pieces or parts of the original design to create new designs for sale or personal use. All Sales are final. You cannot use my designs, purchased or free, in classes without my permission. Each class member must purchase from my web site. Instructors are not allowed to share, copy, duplicate or in any manner distribute my designs. Read my full copyright here: http://www.embroiderygarden.com/shop/copyright-notice.html
18
TriFold Wallet 6x10 Hoop
Our ‘In the Hoop Trifold Wallet’ is made completely in your hoop, has slots for 4 credit cards and a fully lined zippered pocket for change, etc. It folds neatly and secures with a snap. The flap, inside zippered pocket and outside of the wallet are stippled quilted.
~~~~~ Note: Designer SE users make sure you’re using the 150x240 files 2 fabrics were used in our sample. Fabric 1 (main fabric ~ cream/gray/teal) was used for the outside and inside pieces. Fabric 2 (gray dot) was used for the credit card pockets and the lining for the zippered pocket. This design is not suited for directional fabric. We use spray (lightly) to secure all pieces unless noted otherwise. READ THROUGH INSTRUCTIONS BEFORE BEGINNING The fabric pieces needed will be referred to by letters A ~ M These pieces are listed under Supplies Needed below in the order they are used in the design.
1
If you want to add an optional fabric loop to attach hardware and a strap, make the loop before starting. When flat it should be 3” long. Width depends on the hardware you’re using. The quilted flap and outside of the wallet has to be stitched first. Do not stitch the last step of this design. It is an X in the lower right corner. This step is here to keep the machine foot from returning to the center and possibly hitting the zipper pull.
Supplies Needed: Flap:
*1 piece of Warm & Natural thin cotton batting 6” x 8” A *2 pieces of fabric 1, 6”w x 8”h B, C
Quilted Outside of Wallet
*1 piece of Warm & Natural thin cotton batting 7.50” x 11.50” D *1 piece of fabric 1, 7.50” x 11.50” E
Wallet:
*1 piece of fabric 1, 7.50”w x 6”h F *2 pieces of fabric 2 (credit card pockets) 7.50”w x 7”h ~ Fold both pieces wrong sides together to measure 7.50”w x 3.50”h G, H *1 piece of fabric 1, 7.50”w x 2.50”h I ~ Fold the bottom long edge of this piece under ½”. Be sure to measure. After folding under, press. A photo is below in the instructions of this piece. *2 piece of fabric 2, 7.50”w x 5”h J, K *1 piece of fabric 1, 7.50”w x 5”h L *1 piece of Warm & Natural thin cotton batting 7.50” x 4.50” M *1 Zipper 9”. No metal teeth. The zipper can be longer. *1 snap set size 20 – We use KamSnaps www.kamsnaps.com
~~~~~ Pay attention to the photos in the instructions. Have your hoop orientated as shown.
Make the Flap Hoop poly mesh stabilizer (soft cutaway) in a 5x7 hoop. Place warm & natural piece A centered in your hoop. Place fabric B, right side up over the warm & natural.
2
1.Stipple quilting Place fabric piece C, right side down on top of B.
2.This step stitches the flap together. Remove the flap from the hoop. Trim around the flap ¼” from the stitching on all sides. Clip the corners diagonally. Turn the flap to the right side. Push out the corners nicely. Press. Machine baste the raw edges together close to the edge. Set the flap aside.
Make the Quilted Outside Hoop poly mesh stabilizer (soft cutaway) in a 6x10 hoop Place warm & natural piece D centered in your hoop. Place fabric E, right side up over the warm & natural. 1.Stipple Remove piece from the hoop. Trim stabilizer away. Set this piece aside.
3
Make the Wallet Hoop poly mesh stabilizer (soft cutaway) in a 6x10 hoop 1.Stitch this step onto the stabilizer only. It’s a placement line.
Place piece F right side up, with one 7.50” edge even with the placement line.
2.This step stitches a placement line for the flap that will be used later.
4
Measure down .75” from the flap placement line and place pocket piece G as shown below. Tape the pocket in place along the fold.
Stitch step 3. This step secures the pocket at the bottom of the pocket. Place pocket piece H with the raw edges even with the bottom of piece F As shown below. Tape the pocket in place.
5
Stitch step 4. This step stitches the dividing lines in the credit card pockets.
Stitch step 5. This step stitches the placement lines for the zipper. Place the zipper, right side up, with the pull on the left centered between the placement lines. The pull and the stop will be out of the hoop. Tape the zipper in place.
6
Stitch step 6. This step will stitch the zipper in place.
Next you will place piece I. This is the piece that has the ½” edge folded under.
7
Place piece I, right side down with the unfolded edge even with the bottom of pocket piece H.
Stitch step 7. This step stitches piece I on. Fold I down so that the fold is even with the top edge of the teeth of the zipper. Press the seam.
Close up of I pressed down and aligned with the top edge of the zipper teeth.
8
Turn the hoop to the back side. Place piece J right side down with one 7.50” edge even with the top edge of the zipper tape. Secure this edge in place.
Turn the hoop to the front side. Tape I in place with the fold even with the top of the zipper teeth. Stitch step 8. This step stitches I & J to the zipper.
9
Stitch step 9. This step stitches a decorative stitch across piece I.
Turn the hoop to the back side. Fold piece J up and tape it in place. Do not use spray.
10
Place piece K right side down with one 7.50” edge even with the bottom edge of the zipper tape. Secure the edge in place.
Turn the hoop to the front side. Place piece L right side down with one 7.50” even with the bottom edge of the zipper tape. Secure the edge in place.
Stitch step 10. This step stitches pieces K & L to the zipper. Place the warm & natural piece M with one 7.50” edge even with the seam just sewn.
11
Fold piece L down over the warm & natural. Use spray to secure.
Stitch step 11. This step stitches the stipple quilting on the pocket. Turn the hoop to the back side. Fold piece K down and secure. Carefully trim the stabilizer from the zipper. It’s easier to do it now than later.
12
Fold piece J down. Tape in place.
Stitch step 12. This step stitches a line near the bottom of the hoop as shown in the photo below.
13
Unzip the zipper half way as shown by the black arrow in the photo below.
*Optional: If you want to add a loop to add hardware and a strap, add it now. Make a 3” fabric strap. Fold the strap in half. Place the strap on the front side of the hoop on the LEFT hand side as shown below. Have the fold of the loop about 1/4” past the credit card slot stitching. Have the loop edge even with the top of the second pocket. Tape in place. Note: We’re adding our hardware at this time too.
14
Place the flap, right side up (the side with the stipple) even with the flap placement line at the top of the hoop. Mark sure the flap is centered. Tape the flap in place.
Place the quilted outside you created first, right side down centered on top of the hoop. Pin in place through all layers out of the way of the foot.
15
Stitch step 13. This step stitches the wallet together. The design is finished. Remove the hoop from the machine. Do not stitch the ‘X’. Trim around the design ¼” from the stitching except at the bottom leave ½”. If you added the fabric loop, do not cut the ends off. Clip corners diagonally.
Trim the excess layers from the opening. Leave the pieces that form the opening. Turn the wallet to the right side. Push out the sides and corners nicely. Turn the raw edges at the bottom in. Press the wallet.
16
Time to install the snap. The male snap will be installed on the flap The male part of the snap will be on the inside. Center the snap on the flap about ¼” up from the edge.
Place credit cards into the slots. You are doing this to determine the placement for the female snap. Fold the wallet in half. Make sure the turned in edges are even.
Fold the flap down. Mark where the snap needs to go.
17
The female snap will be installed from the inside of the wallet. The female part of the snap will be on the outside of the wallet.
Make sure the folded in edges at the opening are even. Using a ladder stitch (you can google for it) close the opening. The ladder stitch is easy to do and makes an almost invisible closing.
©Embroidery Garden LLC LEGAL NOTICE, ALL RIGHTS RESERVED All of my designs are Copyrighted and treated as software. Purchase of designs from Embroidery Garden is a license to use the designs. Any form of sharing, loaning, copying, duplicating, re-selling or any other transfer of my designs, whether purchased or a free design, is strictly prohibited. You can combine my design with other designs and/ or fonts. You CAN NOT take my designs apart and use any pieces or parts of the original design to create new designs for sale or personal use. All Sales are final. You cannot use my designs, purchased or free, in classes without my permission. Each class member must purchase from my web site. Instructors are not allowed to share, copy, duplicate or in any manner distribute my designs. Read my full copyright here: http://www.embroiderygarden.com/shop/copyright-notice.html
18
