installation instructions - Honda Parts
INSTALLATION INSTRUCTIONS
Accessory
Application
MOONROOF VISOR P/N 08R01-T0A-100
2012 CR-V
Publications No.
AII 12083 Issue Date
DEC 2011
Put this information in the glove box with the vehicle owner’s manual. PARTS LIST
TOOLS AND SUPPLIES REQUIRED Phillips screwdriver 10 mm Offset wrench
Moonroof visor
Ruler Isopropyl alcohol Shop towel Masking tape Felt-tip pen
2
Front brackets
The following tool is available through the Honda Tool and Equipment program. On the iN, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under “Search.” Or call 888-424-6857. • Torque Screwdriver (T/N CDI401SM) Illustration of the Moonroof Visor Installed on the Vehicle
2
Side brackets
4
Screws
4
Nuts
4
Protective tapes
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
MOONROOF VISOR
Q0N1502AD
AII 46215 (1112)
08R01-T0A-1000-90
1 of 6
INSTALLATION
3.
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
Locate the indentation on the right side of the moonroof opening. Measure 50 mm (2.0 in.) toward the front of the vehicle, and make one mark on the roof panel. Repeat the same procedure on the left side of the vehicle. FRONT
ROOF PANEL
NOTE: • Do not damage the paint finish when you install the moonroof visor. • The moonroof visor should only be installed if the ambient air temperature is 15°C (60°F) or above. • To allow the adhesive to cure, do not wash the vehicle for 24 hours. Please advise your customer. MARK
FRONT
FRONT
MARK
Installing the Moonroof Visor 1.
Clean and wax the area to be covered with a highquality paste wax. 50 mm (2.0 in.) FRONT
INDENTATION ROOF PANEL
50 mm (2.0 in.) FELT-TIP PEN
INDENTATION Q0N1202AD
2 SHOP TOWELS Insert into the corner.
AIR DEFLECTOR
Q0N1201AD
2.
Open the moonroof. Roll up two shop towels, and insert them between the roof panel and air deflector to lower the air deflector. Take care not to damage the air deflector.
2 of 6
AII 46215 (1112)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
4.
Using isopropyl alcohol on a shop towel, clean the roof area where the protective tape will attach. Do not wipe off the mark. MARK
7.
Clean with isopropyl alcohol.
Locate the third indentation in from right side of the moonroof opening as shown. Using isopropyl alcohol on a shop towel, clean the roof area where the protective tape will attach. Clean with isopropyl alcohol.
FRONT
ROOF PANEL
Align.
PROTECTIVE TAPE 10 mm (0.4 in.)
PROTECTIVE TAPE PROTECTIVE TAPE ROOF PANEL
THIRD INDENTATION
CROSS SECTION
CROSS SECTION PROTECTIVE TAPE
ROOF PANEL
FRONT FRONT Clean with isopropyl alcohol.
ROOF PANEL
MARK 10 mm (0.4 in.)
PROTECTIVE TAPE
Q0N1204AD
8.
Remove the adhesive backing from one protective tape. Starting at the top edge, install the protective tape at the third indentation in from right side of the moonroof opening.
9.
Repeat steps 7 and 8 to install the protective tape on the left side of moonroof opening.
FRONT
PROTECTIVE TAPE
CROSS SECTION ROOF PANEL
Q0N1203BD
5.
Remove the adhesive backing from one protective tape, and attach it to the right side of roof panel from the mark. Wrap 10 mm (0.4 in.) of protective tape around the lip of the moonroof opening. Remove the mark.
6.
Repeat steps 4 and 5 to install the protective tape on the left side of moonroof opening.
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
THIRD INDENTATION
AII 46215 (1112)
3 of 6
10. Place one side bracket into position over the protective tape, and tape it into position with a piece of masking tape. Repeat the same procedure to install the side bracket on the left side of the moonroof opening. SIDE BRACKET
PROTECTIVE TAPE
11. Place one front bracket into position over the protective tape, and align the lower edge with the indentation on the roof panel. Tape the bracket in position with a piece of masking tape. Repeat the same procedure to install the other front bracket on the moonroof opening.
SIDE BRACKET
PROTECTIVE TAPE
ROOF PANEL
MASKING TAPE
FRONT BRACKET
ROOF PANEL
CROSS SECTION MASKING TAPE
FRONT BRACKET
CROSS SECTION
FRONT FRONT ROOF PANEL Q0N1205AD
ROOF PANEL Q0N1206AD
4 of 6
AII 46215 (1112)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
12. Set the moonroof visor on the vehicle roof in front of the moonroof opening, and adjust its position so the holes in the visor are aligned with the holes in the front brackets. Loosely install the moonroof visor to the front brackets with two screws and two nuts. Remove the masking tapes from the front brackets.
14. Position the moonroof visor with equal spacing on each sides. Check that the rubber molding is not twisted or rolled under the visor. CROSS SECTION
2 SCREWS Loosely install. MOONROOF VISOR
RUBBER MOLDING Not twisted or rolled under the visor.
2 SCREWS SIDE 2 NUTS 2 SIDE BRACKETS
RUBBER MOLDING ROOF PANEL
Push. CROSS SECTION
2 FRONT BRACKETS
FRONT
2 NUTS
Equal spacing. Q0N1207BD
13. Loosely install the moonroof visor to the side brackets with two screws and two nuts. Remove the masking tape from the side brackets. Equal spacing.
2 SCREWS Loosely install.
MOONROOF VISOR
FRONT 2 NUTS
2 NUTS FRONT 2 SCREWS
Push. 2 SIDE BRACKETS
RUBBER MOLDING
2 FRONT BRACKETS
CROSS SECTION Q0N1209BD
FRONT MOONROOF VISOR
ROOF PANEL
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
Q0N1208BD
15. Tighten two screws and two nuts on each side of the vehicle first, then tighten two screws and two nuts on the front. Tighten while applying pressure so that there is no gap between the brackets and the roof panel. Torque the screws to 2 N·m (1.5 lbf·ft).
AII 46215 (1112)
5 of 6
16. Remove the IMPORTANT INFORMATION label and the shop towels. IMPORTANT INFORMATION LABEL Remove.
FRONT
MOONROOF VISOR Q0N1501AD
CARE OF THE MOONROOF VISOR • To avoid damaging the surface, never use ammoniabased cleaners or solvents to clean the moonroof visor. • Clean with a solution of mild dishwashing soap and water using a soft cloth or chamois. • To remove fine scratches and restore the original luster, use Meguiar’s Mirror Glaze plastic cleaner and polish or an equivalent high-quality plastic cleaner.
6 of 6
AII 46215 (1112)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
Accessory
Application
MOONROOF VISOR P/N 08R01-T0A-100
2012 CR-V
Publications No.
AII 12083 Issue Date
DEC 2011
Put this information in the glove box with the vehicle owner’s manual. PARTS LIST
TOOLS AND SUPPLIES REQUIRED Phillips screwdriver 10 mm Offset wrench
Moonroof visor
Ruler Isopropyl alcohol Shop towel Masking tape Felt-tip pen
2
Front brackets
The following tool is available through the Honda Tool and Equipment program. On the iN, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under “Search.” Or call 888-424-6857. • Torque Screwdriver (T/N CDI401SM) Illustration of the Moonroof Visor Installed on the Vehicle
2
Side brackets
4
Screws
4
Nuts
4
Protective tapes
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
MOONROOF VISOR
Q0N1502AD
AII 46215 (1112)
08R01-T0A-1000-90
1 of 6
INSTALLATION
3.
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
Locate the indentation on the right side of the moonroof opening. Measure 50 mm (2.0 in.) toward the front of the vehicle, and make one mark on the roof panel. Repeat the same procedure on the left side of the vehicle. FRONT
ROOF PANEL
NOTE: • Do not damage the paint finish when you install the moonroof visor. • The moonroof visor should only be installed if the ambient air temperature is 15°C (60°F) or above. • To allow the adhesive to cure, do not wash the vehicle for 24 hours. Please advise your customer. MARK
FRONT
FRONT
MARK
Installing the Moonroof Visor 1.
Clean and wax the area to be covered with a highquality paste wax. 50 mm (2.0 in.) FRONT
INDENTATION ROOF PANEL
50 mm (2.0 in.) FELT-TIP PEN
INDENTATION Q0N1202AD
2 SHOP TOWELS Insert into the corner.
AIR DEFLECTOR
Q0N1201AD
2.
Open the moonroof. Roll up two shop towels, and insert them between the roof panel and air deflector to lower the air deflector. Take care not to damage the air deflector.
2 of 6
AII 46215 (1112)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
4.
Using isopropyl alcohol on a shop towel, clean the roof area where the protective tape will attach. Do not wipe off the mark. MARK
7.
Clean with isopropyl alcohol.
Locate the third indentation in from right side of the moonroof opening as shown. Using isopropyl alcohol on a shop towel, clean the roof area where the protective tape will attach. Clean with isopropyl alcohol.
FRONT
ROOF PANEL
Align.
PROTECTIVE TAPE 10 mm (0.4 in.)
PROTECTIVE TAPE PROTECTIVE TAPE ROOF PANEL
THIRD INDENTATION
CROSS SECTION
CROSS SECTION PROTECTIVE TAPE
ROOF PANEL
FRONT FRONT Clean with isopropyl alcohol.
ROOF PANEL
MARK 10 mm (0.4 in.)
PROTECTIVE TAPE
Q0N1204AD
8.
Remove the adhesive backing from one protective tape. Starting at the top edge, install the protective tape at the third indentation in from right side of the moonroof opening.
9.
Repeat steps 7 and 8 to install the protective tape on the left side of moonroof opening.
FRONT
PROTECTIVE TAPE
CROSS SECTION ROOF PANEL
Q0N1203BD
5.
Remove the adhesive backing from one protective tape, and attach it to the right side of roof panel from the mark. Wrap 10 mm (0.4 in.) of protective tape around the lip of the moonroof opening. Remove the mark.
6.
Repeat steps 4 and 5 to install the protective tape on the left side of moonroof opening.
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
THIRD INDENTATION
AII 46215 (1112)
3 of 6
10. Place one side bracket into position over the protective tape, and tape it into position with a piece of masking tape. Repeat the same procedure to install the side bracket on the left side of the moonroof opening. SIDE BRACKET
PROTECTIVE TAPE
11. Place one front bracket into position over the protective tape, and align the lower edge with the indentation on the roof panel. Tape the bracket in position with a piece of masking tape. Repeat the same procedure to install the other front bracket on the moonroof opening.
SIDE BRACKET
PROTECTIVE TAPE
ROOF PANEL
MASKING TAPE
FRONT BRACKET
ROOF PANEL
CROSS SECTION MASKING TAPE
FRONT BRACKET
CROSS SECTION
FRONT FRONT ROOF PANEL Q0N1205AD
ROOF PANEL Q0N1206AD
4 of 6
AII 46215 (1112)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
12. Set the moonroof visor on the vehicle roof in front of the moonroof opening, and adjust its position so the holes in the visor are aligned with the holes in the front brackets. Loosely install the moonroof visor to the front brackets with two screws and two nuts. Remove the masking tapes from the front brackets.
14. Position the moonroof visor with equal spacing on each sides. Check that the rubber molding is not twisted or rolled under the visor. CROSS SECTION
2 SCREWS Loosely install. MOONROOF VISOR
RUBBER MOLDING Not twisted or rolled under the visor.
2 SCREWS SIDE 2 NUTS 2 SIDE BRACKETS
RUBBER MOLDING ROOF PANEL
Push. CROSS SECTION
2 FRONT BRACKETS
FRONT
2 NUTS
Equal spacing. Q0N1207BD
13. Loosely install the moonroof visor to the side brackets with two screws and two nuts. Remove the masking tape from the side brackets. Equal spacing.
2 SCREWS Loosely install.
MOONROOF VISOR
FRONT 2 NUTS
2 NUTS FRONT 2 SCREWS
Push. 2 SIDE BRACKETS
RUBBER MOLDING
2 FRONT BRACKETS
CROSS SECTION Q0N1209BD
FRONT MOONROOF VISOR
ROOF PANEL
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
Q0N1208BD
15. Tighten two screws and two nuts on each side of the vehicle first, then tighten two screws and two nuts on the front. Tighten while applying pressure so that there is no gap between the brackets and the roof panel. Torque the screws to 2 N·m (1.5 lbf·ft).
AII 46215 (1112)
5 of 6
16. Remove the IMPORTANT INFORMATION label and the shop towels. IMPORTANT INFORMATION LABEL Remove.
FRONT
MOONROOF VISOR Q0N1501AD
CARE OF THE MOONROOF VISOR • To avoid damaging the surface, never use ammoniabased cleaners or solvents to clean the moonroof visor. • Clean with a solution of mild dishwashing soap and water using a soft cloth or chamois. • To remove fine scratches and restore the original luster, use Meguiar’s Mirror Glaze plastic cleaner and polish or an equivalent high-quality plastic cleaner.
6 of 6
AII 46215 (1112)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
