installation of sti-6528 bopper stopper® weather cover for stand alone
5.42 in. (138mm)
Safety Technology International, Inc.
Safety Technology International (Europe) Ltd.
2306 Airport Road • Waterford, Michigan 48327-1209 Phone: 248-673-9898 • Fax: 248-673-1246 Toll Free: 800-888-4784 • E-mail: [email protected] Web: www.sti-usa.com
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch Worcestershire • B98 0HU • England Tel: 44 (0) 1527 520 999 • Fax: 44 (0) 1527 501 999 E-mail: [email protected] • Web: www.sti-europe.com
COVER
WALL/DOOR
A
#10 x 1-1/2 SCREW
GASKET FRAME DRILL (4) HOLES (SEE INSTALLATION 2 AND 3 BELOW)
5.41 in. (138mm)
19018 #8-10 ANCHOR
3.55 in. (90mm)
COVER A INSIDE OF FRAME 4.15 in. (105mm) 5.42 in. (138mm)
2.37 in. (60mm) SECTION A-A
A
#10 x 1-1/2 SCREW
GASKET FRAME DRILL (4) HOLES (SEE INSTALLATION 2 AND 3 BELOW)
5.41 in. (138mm)
19018 #8-10 ANCHOR
3.55 in. (90mm)
A
INSTALLATION: 1. Place frame in position against wall or door and mark all 4 hole locations. 2. Remove frame. If using anchors, drill (4) 1/4” holes, 1 3/8” deep. If anchors are not used, drill (4) 5/32” holes, 1 3/8” deep. 3. Insert the #8-10 anchors (if used). 4. Align top 2 holes in gasket with top 2 anchor holes and apply gasket. 5. Place cover into frame hinge pockets, rotate cover open and fasten with #10 screws. NOTE: Over tightening of screws may cause cover to NOT close.
INSIDE OF FRAME 4.15 in. (105mm) 5.42 in. (138mm)
2.37 in. (60mm) SECTION A-A
Electronic warranty form at www.sti-usa.com/wc14
INSTALLATION: INSTALLATION OF STI-6528 BOPPER STOPPER® WEATHER COVER FOR STAND ALONE ACCESS CONTROL
1. Place frame position againstand wallinformation or door and mark all 4were hole locations. Allinspecifications shown current as of publication and are subject to change without notice. 2. Remove frame. If using anchors, drill (4) 1/4” holes, 1 3/8” deep. STI-6528IS JAN 2000 If anchors are not used, drill (4) 5/32” holes, 1 3/8” deep. 3. Insert the #8-10 anchors (if used). 4. Align top 2 holes in gasket with top 2 anchor holes and apply gasket. 5. Place cover into frame hinge pockets, rotate cover open and fasten with #10 screws.
Safety Technology International, Inc.
Safety Technology International (Europe) Ltd.
2306 Airport Road • Waterford, Michigan 48327-1209 Phone: 248-673-9898 • Fax: 248-673-1246 Toll Free: 800-888-4784 • E-mail: [email protected] Web: www.sti-usa.com
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch Worcestershire • B98 0HU • England Tel: 44 (0) 1527 520 999 • Fax: 44 (0) 1527 501 999 E-mail: [email protected] • Web: www.sti-europe.com
COVER
WALL/DOOR
A
#10 x 1-1/2 SCREW
GASKET FRAME DRILL (4) HOLES (SEE INSTALLATION 2 AND 3 BELOW)
5.41 in. (138mm)
19018 #8-10 ANCHOR
3.55 in. (90mm)
COVER A INSIDE OF FRAME 4.15 in. (105mm) 5.42 in. (138mm)
2.37 in. (60mm) SECTION A-A
A
#10 x 1-1/2 SCREW
GASKET FRAME DRILL (4) HOLES (SEE INSTALLATION 2 AND 3 BELOW)
5.41 in. (138mm)
19018 #8-10 ANCHOR
3.55 in. (90mm)
A
INSTALLATION: 1. Place frame in position against wall or door and mark all 4 hole locations. 2. Remove frame. If using anchors, drill (4) 1/4” holes, 1 3/8” deep. If anchors are not used, drill (4) 5/32” holes, 1 3/8” deep. 3. Insert the #8-10 anchors (if used). 4. Align top 2 holes in gasket with top 2 anchor holes and apply gasket. 5. Place cover into frame hinge pockets, rotate cover open and fasten with #10 screws. NOTE: Over tightening of screws may cause cover to NOT close.
INSIDE OF FRAME 4.15 in. (105mm) 5.42 in. (138mm)
2.37 in. (60mm) SECTION A-A
Electronic warranty form at www.sti-usa.com/wc14
INSTALLATION: INSTALLATION OF STI-6528 BOPPER STOPPER® WEATHER COVER FOR STAND ALONE ACCESS CONTROL
1. Place frame position againstand wallinformation or door and mark all 4were hole locations. Allinspecifications shown current as of publication and are subject to change without notice. 2. Remove frame. If using anchors, drill (4) 1/4” holes, 1 3/8” deep. STI-6528IS JAN 2000 If anchors are not used, drill (4) 5/32” holes, 1 3/8” deep. 3. Insert the #8-10 anchors (if used). 4. Align top 2 holes in gasket with top 2 anchor holes and apply gasket. 5. Place cover into frame hinge pockets, rotate cover open and fasten with #10 screws.
