PISCO SPEED CONTROL SPATTER
Speed Controller for use in Environments of Spatters
Speed Controller
Spatter The products listed in this page are ECO-friendly products.
Characteristics
* Please refer to page 4 for the details of ECO-friendly products.
Model
JSC Elbow
Specifications T
JSC6-02
V-0
JSC8-01
V-0
JSC8-02
V-0
JSC8-03 V-0
No (13)
(2)
JSC10-02
Material
Parts
(6)
(5)
(11) (9) (8) Sealock-coated
V-0
JSC10-03 V-0
(1) Cover
flame-retarded resin
(2) Lock nut
aluminum (color: silver or black)
JSC10-04 V-0
(3) Thread body
nickel-plated brass
JSC12-03 V-0
(4) Elastic sleeve NBR
(7)
(12)
(10)
V-0
JSC8-04 V-0
(1)
(4)
V-0
JSC6-01
JSC6-03 V-0
Construction
(3)
V-0
JSC12-04 V-0
(5) Release ring
flame-retarded resin
(6) Tube
Spatter tube
(7) Cover
flame-retarded resin
1 pc. in a bag
(8) Guide ring
nickel-plated brass
(9) Lock claws
stainless steel
(10) Diaphragm
NBR
(11) O-ring
NBR
(12) Resin body
flame-retarded resin
(13) Needle
nickel-plated brass
Valve
Operating temp. range
øD
7.25psi (0.05MPa) 〈2.90psi (0.02MPa) for low cracking pressure 32 ~ 140°F (0 ~ 60°C)
JSC4-01 JSC6-M5
Option *1. For , please select a control direction. *2. For , please enter "K" if low cracking pressure type is desired, otherwise leave it blank. *3. The model with low sales average may be build to order production. For details, please contact Pisco sales ofce or sales representative.
* The gasket material of M thread is SPCC + NBR.
Model Designation (Example) JSC 6 (1)
(2)
01 A (3)
(4)
Detailed Safety Instructions
V-0 (5)
Before using the PISCO device, be sure to read the "Safety Instructions", "Common Safety Instructions for Products Listed in This Manual" on page 13 to 15 and "Common Safety Instructions for Controllers" on page 64.
(6)
(1) Type (2) Tube dia. (øD) mm size Code
4
6
8
10
12
Dia.
ø4
ø6
ø8
ø10
ø12
(3) Thread size (T) Metric thread
Taper pipe thread
Code
M5
01
02
03
04
size
M5×0.8
R1/8
R1/4
R3/8
R1/2
(4) Control direction A: Meter-out control The flow rate of air Control flow entering from the thread side can be controlled, whereas air entering from the joint side comes out from the thread side at the same (not controlled) Free flow flow rate.
B: Meter-in control Free flow
Control flow
The flow rate of air entering from the joint side can be controlled, whereas air entering from the thread side comes out from the joint side at the same (not controlled) flow rate.
Warnings : 1. Adjust the flow-rate by opening the needle gradually from the fully closed position. With the needle open, there are chances of the device flying out. Turn the needle clockwise to close or counterclockwise to open. 2. Do not subject the product to forcible swinging or rotation. Otherwise the body may suffer damage or develop leakage. Cautions : 1. The Speed Controller is designed to tolerate some air ow at fully closed position. Therefore do not use it for applications that permits no air ow. 2. After adjusting speed of actuator, please make sure to put the cover back, otherwise spatter may cause an operational trouble. 3. When you use a covered tube, be sure to cut the covering into the specied dimensions (see below) before use. Failure to do so may result in the coming off of the tube, leakage or inability to connect the tube. Tube dia. ø4mm ø6mm ø8mm ø10mm ø12mm Spatter Tube Cover cutting 15.5mm 16.5mm 17.5mm 20.0mm 23.5mm (Covered Tube) Dimension (C) (0.61in.) (0.65in.) (0.69in.) (0.79in.) (0.92in.)
C
Vacuum
Check valve crackting pressure
V-0
Actuator
Operating pressure range
Air 14.5 ~ 130psi (0.1 ~ 0.9MPa) (at 0 ~ 20°C) *² 〈7.25 ~ 72.5psi (0.05 ~ 0.5MPa) for low cracking pressure
V-0
JSC4-M5
Tube
Fluid medium
JSCøD-T
Control
A fire-resistant resin prevents spattering. (Equivalent to ULV-0) Both needle and joint sections are covered to prevent spattering.
(6) Flame retardation (Code: V-0) * Be sure to enter V-0. Otherwise, your specification is understood to be a standard type.
Robot Parts
K: Low cracking pressure type (Check valve cracking pressure: 0.02MPa, operating pressure range: 0.05 ~ 0.5MPa) No code: Standard specification
Plarailchain
(5) Check valve specification
69
Products
3,6&286$,1&
29(56($60$5.(7,1*'(3$570(17
::5,*+7:22'$9((/0+8567,/86$ 7(/ )$; :HEVLWH ZZZSLVFRFRP(PDLO LQTXLU\#SLVFRFRP
0,1$0,0,12:$.$0,,1$1$*$1235() -$3$1 7(/ )$; :HEVLWH ZZZSLVFRFRMSHQJOLVKSLVFRKWP(PDLO LQWO#SLVFRFRMS
1,+213,6&26,1*$325(37(/7'
+($'2)),&($1'3/$17
%/.$1*02.,2$9(18(7(&+3/$&(6,1*$325( 7(/ )$; :HEVLWH ZZZSLVFRFRPVJ(PDLO SLVFR#SDFLÀFQHWVJ
,=8+$
Speed Controller
Spatter The products listed in this page are ECO-friendly products.
Characteristics
* Please refer to page 4 for the details of ECO-friendly products.
Model
JSC Elbow
Specifications T
JSC6-02
V-0
JSC8-01
V-0
JSC8-02
V-0
JSC8-03 V-0
No (13)
(2)
JSC10-02
Material
Parts
(6)
(5)
(11) (9) (8) Sealock-coated
V-0
JSC10-03 V-0
(1) Cover
flame-retarded resin
(2) Lock nut
aluminum (color: silver or black)
JSC10-04 V-0
(3) Thread body
nickel-plated brass
JSC12-03 V-0
(4) Elastic sleeve NBR
(7)
(12)
(10)
V-0
JSC8-04 V-0
(1)
(4)
V-0
JSC6-01
JSC6-03 V-0
Construction
(3)
V-0
JSC12-04 V-0
(5) Release ring
flame-retarded resin
(6) Tube
Spatter tube
(7) Cover
flame-retarded resin
1 pc. in a bag
(8) Guide ring
nickel-plated brass
(9) Lock claws
stainless steel
(10) Diaphragm
NBR
(11) O-ring
NBR
(12) Resin body
flame-retarded resin
(13) Needle
nickel-plated brass
Valve
Operating temp. range
øD
7.25psi (0.05MPa) 〈2.90psi (0.02MPa) for low cracking pressure 32 ~ 140°F (0 ~ 60°C)
JSC4-01 JSC6-M5
Option *1. For , please select a control direction. *2. For , please enter "K" if low cracking pressure type is desired, otherwise leave it blank. *3. The model with low sales average may be build to order production. For details, please contact Pisco sales ofce or sales representative.
* The gasket material of M thread is SPCC + NBR.
Model Designation (Example) JSC 6 (1)
(2)
01 A (3)
(4)
Detailed Safety Instructions
V-0 (5)
Before using the PISCO device, be sure to read the "Safety Instructions", "Common Safety Instructions for Products Listed in This Manual" on page 13 to 15 and "Common Safety Instructions for Controllers" on page 64.
(6)
(1) Type (2) Tube dia. (øD) mm size Code
4
6
8
10
12
Dia.
ø4
ø6
ø8
ø10
ø12
(3) Thread size (T) Metric thread
Taper pipe thread
Code
M5
01
02
03
04
size
M5×0.8
R1/8
R1/4
R3/8
R1/2
(4) Control direction A: Meter-out control The flow rate of air Control flow entering from the thread side can be controlled, whereas air entering from the joint side comes out from the thread side at the same (not controlled) Free flow flow rate.
B: Meter-in control Free flow
Control flow
The flow rate of air entering from the joint side can be controlled, whereas air entering from the thread side comes out from the joint side at the same (not controlled) flow rate.
Warnings : 1. Adjust the flow-rate by opening the needle gradually from the fully closed position. With the needle open, there are chances of the device flying out. Turn the needle clockwise to close or counterclockwise to open. 2. Do not subject the product to forcible swinging or rotation. Otherwise the body may suffer damage or develop leakage. Cautions : 1. The Speed Controller is designed to tolerate some air ow at fully closed position. Therefore do not use it for applications that permits no air ow. 2. After adjusting speed of actuator, please make sure to put the cover back, otherwise spatter may cause an operational trouble. 3. When you use a covered tube, be sure to cut the covering into the specied dimensions (see below) before use. Failure to do so may result in the coming off of the tube, leakage or inability to connect the tube. Tube dia. ø4mm ø6mm ø8mm ø10mm ø12mm Spatter Tube Cover cutting 15.5mm 16.5mm 17.5mm 20.0mm 23.5mm (Covered Tube) Dimension (C) (0.61in.) (0.65in.) (0.69in.) (0.79in.) (0.92in.)
C
Vacuum
Check valve crackting pressure
V-0
Actuator
Operating pressure range
Air 14.5 ~ 130psi (0.1 ~ 0.9MPa) (at 0 ~ 20°C) *² 〈7.25 ~ 72.5psi (0.05 ~ 0.5MPa) for low cracking pressure
V-0
JSC4-M5
Tube
Fluid medium
JSCøD-T
Control
A fire-resistant resin prevents spattering. (Equivalent to ULV-0) Both needle and joint sections are covered to prevent spattering.
(6) Flame retardation (Code: V-0) * Be sure to enter V-0. Otherwise, your specification is understood to be a standard type.
Robot Parts
K: Low cracking pressure type (Check valve cracking pressure: 0.02MPa, operating pressure range: 0.05 ~ 0.5MPa) No code: Standard specification
Plarailchain
(5) Check valve specification
69
Products
3,6&286$,1&
29(56($60$5.(7,1*'(3$570(17
::5,*+7:22'$9((/0+8567,/86$ 7(/ )$; :HEVLWH ZZZSLVFRFRP(PDLO LQTXLU\#SLVFRFRP
0,1$0,0,12:$.$0,,1$1$*$1235() -$3$1 7(/ )$; :HEVLWH ZZZSLVFRFRMSHQJOLVKSLVFRKWP(PDLO LQWO#SLVFRFRMS
1,+213,6&26,1*$325(37(/7'
+($'2)),&($1'3/$17
%/.$1*02.,2$9(18(7(&+3/$&(6,1*$325( 7(/ )$; :HEVLWH ZZZSLVFRFRPVJ(PDLO SLVFR#SDFLÀFQHWVJ
,=8+$
