SodaStream Fountain Jet A200 Washer Replacement
SodaStream Fountain Jet A200 Washer Replacement
SodaStream Fountain Jet A200 Washer Replacement In this guide, an extra washer will be removed or, a worn out washer will be replaced with a new one.
Written By: Katie Fetters
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
SodaStream Fountain Jet A200 Washer Replacement
INTRODUCTION This guide is to instruct a person on how to remove a worn out washer or remove an extra washer that may have been installed during manufacturing.
TOOLS: Tweezers (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
SodaStream Fountain Jet A200 Washer Replacement
Step 1 — Remove the CO2 tank
With one hand, press in the two gray oval shaped buttons found on either side.
Gently pull back on the cover until it releases from the device.
Remove the back cover of the device.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 5
SodaStream Fountain Jet A200 Washer Replacement
Step 2
Grasp the CO2 tank and twist it in a clockwise motion.
Once the CO2 tank is free, pull it towards you and lift upwards to remove it from the device.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 5
SodaStream Fountain Jet A200 Washer Replacement
Step 3 — removing washers
Flip the device upside down.
Locate the washer, this will be in the valve where the CO2 tank was located.
Using tweezers, remove the old/ extra wash and insert a new washer if needed.
For your machine to function properly, there should only be one washer present. To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-18 06:02:25 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
SodaStream Fountain Jet A200 Washer Replacement In this guide, an extra washer will be removed or, a worn out washer will be replaced with a new one.
Written By: Katie Fetters
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
SodaStream Fountain Jet A200 Washer Replacement
INTRODUCTION This guide is to instruct a person on how to remove a worn out washer or remove an extra washer that may have been installed during manufacturing.
TOOLS: Tweezers (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
SodaStream Fountain Jet A200 Washer Replacement
Step 1 — Remove the CO2 tank
With one hand, press in the two gray oval shaped buttons found on either side.
Gently pull back on the cover until it releases from the device.
Remove the back cover of the device.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 5
SodaStream Fountain Jet A200 Washer Replacement
Step 2
Grasp the CO2 tank and twist it in a clockwise motion.
Once the CO2 tank is free, pull it towards you and lift upwards to remove it from the device.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 5
SodaStream Fountain Jet A200 Washer Replacement
Step 3 — removing washers
Flip the device upside down.
Locate the washer, this will be in the valve where the CO2 tank was located.
Using tweezers, remove the old/ extra wash and insert a new washer if needed.
For your machine to function properly, there should only be one washer present. To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-18 06:02:25 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
