Disassembling Planet Eclipse Etha Frame
Disassembling Planet Eclipse Etha Frame
Disassembling Planet Eclipse Etha Frame This guide will show how to remove the frame from the Etha.
Written By: nicholasj6
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 7
Disassembling Planet Eclipse Etha Frame
INTRODUCTION Removing the frame will allow access to the eyes and solenoid should they need replacement.
TOOLS: Macro Bit Set (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 7
Disassembling Planet Eclipse Etha Frame
Step 1 — Regulator
Firmly grasp hold of the ring on the bottom of the 90 degree silver fitting on the front of the gun.
Pull hard, but slowly, on the macroline where it comes out of silver piece until it comes out.
The macroline is the black hose connecting the regulator to the tank connection. Step 2
Remove the regulator by unscrewing it in a clockwise direction.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 7
Disassembling Planet Eclipse Etha Frame
Step 3 — Battery and Grip Panels
Use the 5/64" hex key to remove the screw shown.
Remove the grip panel by gently holding the bottom of the panel and lifting the panel off.
If you are only replacing the battery, skip the next step. The screws in this guide are interchangeable with those shown in the Eyes replacement guide. Step 4
© iFixit — CC BY-NC-SA
www.iFixit.com
Flip the marker over and use the 5/64" hex key to remove the screw shown.
Remove the grip panel by gently holding the bottom of the panel and lifting the panel off.
Page 4 of 7
Disassembling Planet Eclipse Etha Frame
Step 5
Carefully remove the 9V battery and connector.
Remove the 9V battery from the connector.
Step 6 — Frame
Carefully disconnect the three connectors from the circuit board.
Don't worry about remembering which direction the connectors go in, they will not fit in the board in the wrong direction. © iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 7
Disassembling Planet Eclipse Etha Frame
Step 7
Use the 1/8" hex key to remove the two dome-headed screws by rotating them counter-clockwise.
Step 8
Be very careful during the step to avoid damage to the solenoid or wiring.
Gently separate the top and bottom of the marker.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-07-02 12:31:24 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 7
Disassembling Planet Eclipse Etha Frame
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 7
Disassembling Planet Eclipse Etha Frame This guide will show how to remove the frame from the Etha.
Written By: nicholasj6
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 7
Disassembling Planet Eclipse Etha Frame
INTRODUCTION Removing the frame will allow access to the eyes and solenoid should they need replacement.
TOOLS: Macro Bit Set (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 7
Disassembling Planet Eclipse Etha Frame
Step 1 — Regulator
Firmly grasp hold of the ring on the bottom of the 90 degree silver fitting on the front of the gun.
Pull hard, but slowly, on the macroline where it comes out of silver piece until it comes out.
The macroline is the black hose connecting the regulator to the tank connection. Step 2
Remove the regulator by unscrewing it in a clockwise direction.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 7
Disassembling Planet Eclipse Etha Frame
Step 3 — Battery and Grip Panels
Use the 5/64" hex key to remove the screw shown.
Remove the grip panel by gently holding the bottom of the panel and lifting the panel off.
If you are only replacing the battery, skip the next step. The screws in this guide are interchangeable with those shown in the Eyes replacement guide. Step 4
© iFixit — CC BY-NC-SA
www.iFixit.com
Flip the marker over and use the 5/64" hex key to remove the screw shown.
Remove the grip panel by gently holding the bottom of the panel and lifting the panel off.
Page 4 of 7
Disassembling Planet Eclipse Etha Frame
Step 5
Carefully remove the 9V battery and connector.
Remove the 9V battery from the connector.
Step 6 — Frame
Carefully disconnect the three connectors from the circuit board.
Don't worry about remembering which direction the connectors go in, they will not fit in the board in the wrong direction. © iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 7
Disassembling Planet Eclipse Etha Frame
Step 7
Use the 1/8" hex key to remove the two dome-headed screws by rotating them counter-clockwise.
Step 8
Be very careful during the step to avoid damage to the solenoid or wiring.
Gently separate the top and bottom of the marker.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-07-02 12:31:24 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 7
Disassembling Planet Eclipse Etha Frame
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 7
