1922 GE AOU Fan Power cord Replacement
1922 GE AOU Fan Power cord Replacement
1922 GE AOU Fan Power cord Replacement Replace the power cord on a 1922 GE AOU fan.
Written By: Elias Dorna
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
1922 GE AOU Fan Power cord Replacement
INTRODUCTION Use this guide to replace the power cord on a 1922 GE AOU fan.
TOOLS:
PARTS:
9/32 flat-head Screwdriver (1)
Cloth Wire Power Cord (1)
5/16 Crescent Wrench (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
1922 GE AOU Fan Power cord Replacement
Step 1 — Power cord
Tip the fan to its side and remove the three size 8 screws using a 9/32 flat-head screwdriver.
The screws may be brittle from age, so be careful.
Take the bottom plate off the fan and set it aside.
Step 2
© iFixit — CC BY-NC-SA
www.iFixit.com
Remove the three number 8 screws that hold the switch in place.
Page 3 of 5
1922 GE AOU Fan Power cord Replacement
Step 3
Remove the switch, carefully sliding the speed lever out of its slot.
Don't remove the switch too quickly or you can damage the head-wire.
Step 4
© iFixit — CC BY-NC-SA
www.iFixit.com
Once the switch is free, unscrew the two knurled nuts holding the wires in place.
Page 4 of 5
1922 GE AOU Fan Power cord Replacement
Step 5
Turn the switch over and unscrew the nut securing the wire with the 5/16 crescent wrench.
Remove the switch and set it aside, then pull the wire through the grommet.
Step 6
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-18 06:49:27 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
1922 GE AOU Fan Power cord Replacement Replace the power cord on a 1922 GE AOU fan.
Written By: Elias Dorna
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
1922 GE AOU Fan Power cord Replacement
INTRODUCTION Use this guide to replace the power cord on a 1922 GE AOU fan.
TOOLS:
PARTS:
9/32 flat-head Screwdriver (1)
Cloth Wire Power Cord (1)
5/16 Crescent Wrench (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
1922 GE AOU Fan Power cord Replacement
Step 1 — Power cord
Tip the fan to its side and remove the three size 8 screws using a 9/32 flat-head screwdriver.
The screws may be brittle from age, so be careful.
Take the bottom plate off the fan and set it aside.
Step 2
© iFixit — CC BY-NC-SA
www.iFixit.com
Remove the three number 8 screws that hold the switch in place.
Page 3 of 5
1922 GE AOU Fan Power cord Replacement
Step 3
Remove the switch, carefully sliding the speed lever out of its slot.
Don't remove the switch too quickly or you can damage the head-wire.
Step 4
© iFixit — CC BY-NC-SA
www.iFixit.com
Once the switch is free, unscrew the two knurled nuts holding the wires in place.
Page 4 of 5
1922 GE AOU Fan Power cord Replacement
Step 5
Turn the switch over and unscrew the nut securing the wire with the 5/16 crescent wrench.
Remove the switch and set it aside, then pull the wire through the grommet.
Step 6
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-18 06:49:27 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
