DeWalt D28110 Brush Arm Replacement
DeWalt D28110 Brush Arm Replacement
DeWalt D28110 Brush Arm Replacement The brush arm holds the brushes in place that electrically connect the armature rotor. Replacing this may fix a grinder that won't spin consistently.
Written By: Kean Wee
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
DeWalt D28110 Brush Arm Replacement
INTRODUCTION This guide will walk you through replacing the plastic arms holding the brushes in place. These are both located at the base of the brush motor and are required for electrical connection.
TOOLS:
PARTS:
Spudger (1)
DewaltD28110 Brush Arm (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
DeWalt D28110 Brush Arm Replacement
Step 1 — Back Panel Disassembly
Using the T-15 screwdriver, remove the four 22-mm torx screws holding the back panel in place.
Unplug the grinder before any disassembly.
Step 2
© iFixit — CC BY-NC-SA
www.iFixit.com
Use the edge of the spudger to loosen and remove the back panel.
Page 3 of 5
DeWalt D28110 Brush Arm Replacement
Step 3
Remove the single 20-mm torx screw holding the rear panel in place.
Pull back the rear side of the back panel.
Step 4
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 5
DeWalt D28110 Brush Arm Replacement
Step 5 — Brush Arm
Using the T-6 screwdriver, unscrew torx screw holding the arm in place.
Gently remove the arm from the assembly.
Step 6
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-07-07 01:08:42 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
DeWalt D28110 Brush Arm Replacement The brush arm holds the brushes in place that electrically connect the armature rotor. Replacing this may fix a grinder that won't spin consistently.
Written By: Kean Wee
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 5
DeWalt D28110 Brush Arm Replacement
INTRODUCTION This guide will walk you through replacing the plastic arms holding the brushes in place. These are both located at the base of the brush motor and are required for electrical connection.
TOOLS:
PARTS:
Spudger (1)
DewaltD28110 Brush Arm (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 5
DeWalt D28110 Brush Arm Replacement
Step 1 — Back Panel Disassembly
Using the T-15 screwdriver, remove the four 22-mm torx screws holding the back panel in place.
Unplug the grinder before any disassembly.
Step 2
© iFixit — CC BY-NC-SA
www.iFixit.com
Use the edge of the spudger to loosen and remove the back panel.
Page 3 of 5
DeWalt D28110 Brush Arm Replacement
Step 3
Remove the single 20-mm torx screw holding the rear panel in place.
Pull back the rear side of the back panel.
Step 4
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 5
DeWalt D28110 Brush Arm Replacement
Step 5 — Brush Arm
Using the T-6 screwdriver, unscrew torx screw holding the arm in place.
Gently remove the arm from the assembly.
Step 6
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-07-07 01:08:42 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 5
