installation instructions slim puck led puck - GM Lighting
INSTALLATION INSTRUCTIONS SLIM PUCK LED PUCK
“Lighting Enhanced by Design”
BEFORE YOU START: • Please check local electrical codes before beginning • Turn power off before installing • Make sure to use proper rated wire
TOOLS NEEDED: • Keyhole Saw • Phillips Screwdriver
RECESSED INSTALLATION: 1. Determine the position of your puck(s) and trace a 2-1/4” diameter circle on surface material. Using a keyhole saw or 2-1/4” (58mm) drill bit - cut through surface (Fig. 1). 2. Feed Puck wire through hole, and screw puck mounting ring into surface using two screws (supplied) (Fig. 2).
SlimPuck surface mount ring
SlimPuck with 48” lead
SlimPuck Trim
+
3. Connect feed wires to power supply and snap SlimPuck Trim to SlimPuck. Trim is held magnetically. No need for screws (Fig. 3).
48” - 24AWG leads included
2-1/4”
Fig. 2
SURFACE INSTALLATION: 1. Determine the position of your puck(s) and position SlimPuck surface mount ring. Screw surface mount ring onto surface (Fig. 4).
Fig. 1
2. Making sure that you insert feed wire through SlimPuck surface mount ring slot, position SlimPuck onto surface mount ring. Ring is held magnetically. No need for screws (Fig. 5).
Fig. 3
3. Connect feed wires to power supply and snap SlimPuck Trim to SlimPuck (Fig.3). NOTE: Pucks can be mounted in series. Please observe wattage limitations of power supply. Example: A 20 watt power supply can power up to 8 2-watt Slim Pucks. DO NOT LOAD POWER SUPPLY ABOVE 80% OF MAXIMUM.
Layout Diagrams
Wire Slot
GMSB-W/B (splice box) Power Supply
Fig. 4
+ -
Wire Slot 2 Watt
Power Supply
2 Watt
2 Watt
2 Watt
2 Watt
= 10 Total Watts
+
Fig. 5
-
2 Watt
2 Watt
©2017 GM Lighting
“Lighting Enhanced by Design”
Specifications are subject to change without notice.
2 Watt
2 Watt = 8 Total Watts
9830 W. 190th Street, Unit F Mokena, IL 60448
Toll-Free: (866) 671-0811 FAX: (708) 478-2640
www.gmlighting.net [email protected] SlimPuckInstallation_082417
“Lighting Enhanced by Design”
BEFORE YOU START: • Please check local electrical codes before beginning • Turn power off before installing • Make sure to use proper rated wire
TOOLS NEEDED: • Keyhole Saw • Phillips Screwdriver
RECESSED INSTALLATION: 1. Determine the position of your puck(s) and trace a 2-1/4” diameter circle on surface material. Using a keyhole saw or 2-1/4” (58mm) drill bit - cut through surface (Fig. 1). 2. Feed Puck wire through hole, and screw puck mounting ring into surface using two screws (supplied) (Fig. 2).
SlimPuck surface mount ring
SlimPuck with 48” lead
SlimPuck Trim
+
3. Connect feed wires to power supply and snap SlimPuck Trim to SlimPuck. Trim is held magnetically. No need for screws (Fig. 3).
48” - 24AWG leads included
2-1/4”
Fig. 2
SURFACE INSTALLATION: 1. Determine the position of your puck(s) and position SlimPuck surface mount ring. Screw surface mount ring onto surface (Fig. 4).
Fig. 1
2. Making sure that you insert feed wire through SlimPuck surface mount ring slot, position SlimPuck onto surface mount ring. Ring is held magnetically. No need for screws (Fig. 5).
Fig. 3
3. Connect feed wires to power supply and snap SlimPuck Trim to SlimPuck (Fig.3). NOTE: Pucks can be mounted in series. Please observe wattage limitations of power supply. Example: A 20 watt power supply can power up to 8 2-watt Slim Pucks. DO NOT LOAD POWER SUPPLY ABOVE 80% OF MAXIMUM.
Layout Diagrams
Wire Slot
GMSB-W/B (splice box) Power Supply
Fig. 4
+ -
Wire Slot 2 Watt
Power Supply
2 Watt
2 Watt
2 Watt
2 Watt
= 10 Total Watts
+
Fig. 5
-
2 Watt
2 Watt
©2017 GM Lighting
“Lighting Enhanced by Design”
Specifications are subject to change without notice.
2 Watt
2 Watt = 8 Total Watts
9830 W. 190th Street, Unit F Mokena, IL 60448
Toll-Free: (866) 671-0811 FAX: (708) 478-2640
www.gmlighting.net [email protected] SlimPuckInstallation_082417
