SR-60 IR Heater Upgrade Kit SR-60 IR Heater Upgrade Kit
SR-60 IR Heater Upgrade Kit IR Heater Upgrade Kit (80-0-432125) contains the following parts:
SR-60 IR Heater Upgrade Kit
SR-60 # 1-81 will require additional hardware for mounting
9 – High Pressure Nozzle and Elbow Assemblies (80-0-432103)
9 – 11” Teflon lined Braided Stainless Steel Hoses (80-0-432102) 9 – Inline Filter Assemblies (80-0-432Y)
Filter Assembly detail: A fine mesh stainless steel disc is held in place by a spring retainer
The IR Heater Upgrade Kit improves the heaters performance. The Inline Filter Assemblies filter out debris which can cause blockage of the heater nozzles. The High Pressure Nozzle Assemblies run at 20% more pressure (7 PSI) to improve combustion efficiency and improve high wind performance. For pricing information or to place an order, call the Order Desk (800) 688-5652 Updated: MAY 2007 www.integratedpaving.com 1.800.688.5652
High Pressure Nozzle Installation Instructions for SR-60 machines # 1 - 80 Burners were modified at / around serial # 80 to make it easier to remove the nozzles. SR-60’s that fall in that category will need to make some minor modifications in order to run the high pressure nozzles. If the elbow has a welded nut to thread into, you will not need to modify your burners. This is for SR-60’s that do not have a threaded nut welded to the wall that separates the mixing bell and the elbow. Estimated time to install – 2 hours Tools needed – Dye grinder or drill w/ 5/8” bit, grinder, misc. wrenches, screw drivers
2
Nozzle Installation Instructions – Cont’d Step 1 – Remove heater from carriage. Step 2 – Remove backing plate. *Center burners may have a couple small spot welds that will need to be grinded in order to remove.
Step 3 – Using a dye grinder, or drill and 5/8” drill bit, hollow out hole so the threaded section of the elbow can pass freely. *Using your grinder, clean all rough edges that may cause the nozzle to not sit flush.
Step 4 – Place two washers on the elbow, then push through the modified hole. *Washers will be necessary to achieve proper spacing between the mixing bell and nozzle.
Step 5 - Thread nut on the other side of the wall and tighten to keep in place.
Step 6 – Re-assemble the plumbing, and check for any leaks. After re-mounting burners, set pressure on third stage regulator to 7 psi. 3
SR-60 IR Heater Upgrade Kit
SR-60 # 1-81 will require additional hardware for mounting
9 – High Pressure Nozzle and Elbow Assemblies (80-0-432103)
9 – 11” Teflon lined Braided Stainless Steel Hoses (80-0-432102) 9 – Inline Filter Assemblies (80-0-432Y)
Filter Assembly detail: A fine mesh stainless steel disc is held in place by a spring retainer
The IR Heater Upgrade Kit improves the heaters performance. The Inline Filter Assemblies filter out debris which can cause blockage of the heater nozzles. The High Pressure Nozzle Assemblies run at 20% more pressure (7 PSI) to improve combustion efficiency and improve high wind performance. For pricing information or to place an order, call the Order Desk (800) 688-5652 Updated: MAY 2007 www.integratedpaving.com 1.800.688.5652
High Pressure Nozzle Installation Instructions for SR-60 machines # 1 - 80 Burners were modified at / around serial # 80 to make it easier to remove the nozzles. SR-60’s that fall in that category will need to make some minor modifications in order to run the high pressure nozzles. If the elbow has a welded nut to thread into, you will not need to modify your burners. This is for SR-60’s that do not have a threaded nut welded to the wall that separates the mixing bell and the elbow. Estimated time to install – 2 hours Tools needed – Dye grinder or drill w/ 5/8” bit, grinder, misc. wrenches, screw drivers
2
Nozzle Installation Instructions – Cont’d Step 1 – Remove heater from carriage. Step 2 – Remove backing plate. *Center burners may have a couple small spot welds that will need to be grinded in order to remove.
Step 3 – Using a dye grinder, or drill and 5/8” drill bit, hollow out hole so the threaded section of the elbow can pass freely. *Using your grinder, clean all rough edges that may cause the nozzle to not sit flush.
Step 4 – Place two washers on the elbow, then push through the modified hole. *Washers will be necessary to achieve proper spacing between the mixing bell and nozzle.
Step 5 - Thread nut on the other side of the wall and tighten to keep in place.
Step 6 – Re-assemble the plumbing, and check for any leaks. After re-mounting burners, set pressure on third stage regulator to 7 psi. 3
