DYMO LabelPOINT 100 Rubber Transport Roller Replacement
DYMO LabelPOINT 100 Rubber Transport Roller Replacement
DYMO LabelPOINT 100 Rubber Transport Roller Replacement Replace a damaged rubber transport roller
Written By: Deborah Canas
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 6
DYMO LabelPOINT 100 Rubber Transport Roller Replacement
TOOLS:
PARTS:
Phillips #00 Screwdriver (1)
Rubber Transport Roller (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 6
DYMO LabelPOINT 100 Rubber Transport Roller Replacement
Step 1 — Rear Panel
Slide the panel release button.
Lift the panel.
Step 2 — Remove Label Tape Cassette
Firmly press the cartridge release button with your finger.
You may need to hold the cassette and/or entire device still while pressing the button.
Lift the label tape cassette out of the device.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 6
DYMO LabelPOINT 100 Rubber Transport Roller Replacement
Step 3 — Remove Screws To the Acess Panel
Use Phillips #00 screwdriver to remove three screws
Remove blade cutter
Use Phillips #00 screwdriver to remove remaining two screws from the battery compartment
Step 4
Gently pull the access panel up to separate from the device
Some electrical wiring will be exposed and will not detach. Be careful not to damage any electrical wiring when removing access panel.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 6
DYMO LabelPOINT 100 Rubber Transport Roller Replacement
Step 5 — Remove Back Panel
Use Phillips #00 screwdriver to remove six screws
Slowly separate back panel
Gears attached to the back panel are not secured and have a tendency to fall out. This will cause difficulty when reassembling
Step 6 — Remove Rubber Transport Roller
Gently pull rubber transport roller up to remove
Replace rubber transport roller
To reassemble your device, follow these instructions in reverse order. © iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 6
DYMO LabelPOINT 100 Rubber Transport Roller Replacement This document was last generated on 2017-06-19 02:43:31 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 6
DYMO LabelPOINT 100 Rubber Transport Roller Replacement Replace a damaged rubber transport roller
Written By: Deborah Canas
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 6
DYMO LabelPOINT 100 Rubber Transport Roller Replacement
TOOLS:
PARTS:
Phillips #00 Screwdriver (1)
Rubber Transport Roller (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 6
DYMO LabelPOINT 100 Rubber Transport Roller Replacement
Step 1 — Rear Panel
Slide the panel release button.
Lift the panel.
Step 2 — Remove Label Tape Cassette
Firmly press the cartridge release button with your finger.
You may need to hold the cassette and/or entire device still while pressing the button.
Lift the label tape cassette out of the device.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 6
DYMO LabelPOINT 100 Rubber Transport Roller Replacement
Step 3 — Remove Screws To the Acess Panel
Use Phillips #00 screwdriver to remove three screws
Remove blade cutter
Use Phillips #00 screwdriver to remove remaining two screws from the battery compartment
Step 4
Gently pull the access panel up to separate from the device
Some electrical wiring will be exposed and will not detach. Be careful not to damage any electrical wiring when removing access panel.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 6
DYMO LabelPOINT 100 Rubber Transport Roller Replacement
Step 5 — Remove Back Panel
Use Phillips #00 screwdriver to remove six screws
Slowly separate back panel
Gears attached to the back panel are not secured and have a tendency to fall out. This will cause difficulty when reassembling
Step 6 — Remove Rubber Transport Roller
Gently pull rubber transport roller up to remove
Replace rubber transport roller
To reassemble your device, follow these instructions in reverse order. © iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 6
DYMO LabelPOINT 100 Rubber Transport Roller Replacement This document was last generated on 2017-06-19 02:43:31 AM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 6 of 6
