T-H2S-DV May 2012 - SupplyHouse.com
T-H2S-DV 18-1/2" (470mm) 12-1/2" (320mm)
12-1/2" (316mm)
3-1/2" (90mm)
Ø4" (102mm) Female
Male Ø4" (100.8mm)
3/4" (18.8mm)
2-3/4" (69.1mm) INTAKE
C
25-1/2" (649mm)
UP
®
2-3/4" (71.8mm) EXHAUST
6-5/8" (168.4mm)
1/2" (12.5mm)
29-1/2" (751mm)
6-1/4" (161.5mm)
1-1/4" (29.2mm) COLD
GAS 6" (153.6mm)
120VAC 2-1/4" (58.2mm)
HOT 7-1/4" (182.1mm) 120VAC 8-1/2" (216.3mm)
4-5/8" (116.8mm) GAS
HOT 5-5/8" (142.2mm)
COLD 8-5/8" (220.6mm)
6-1/4" (159.1mm) Condensate Drain Port
10-1/2" (266.8mm) Condensate Drain Port
Dimension Hot/Cold/Gas Connection Clearances
H25.6” x W18.5” x D12.4” Weight: 73 lbs 3/4” NPT Top: 12“ Bottom: 12” Front: 4” Back: 0.5" Sides: 3“
Features
Venting & Combustion
High Efficiency, Condensing Model Low Emission, Low NOx Safety Features: Air-Fuel Ratio (AFR) sensor Exhaust & Water Temperature safety Control Overheat Cutoff Fuse Internal Freeze-Protection System
Secondary Heat Exchanger is made of SS 316L
Built-in temperature, flow rate, and diagnostic display Power Cord included Temperature Remote Controller included (TM-RE30)
Horizontal or Vertical Installation Power Vent Electric Ignition 4" ; 50' Max Length, 5 elbows max 3" ; 25' Max Length, 2 elbows max (90°elbow = 5' equivalent length) Flue 3" or 4" O.D. Schedule 40 PVC/ ABS Venting (PVC Adaptor included, TH-PA01) Category III / IV Stainless Steel Intake 3" or 4" O.D. ABS, PVC, Galvanized Steel, Corrugated Stainless Steel or Category III/IV Stainless Steel
Accessories
TH-PC02 Pipe Cover TH-NT01 Neutralizer Kit TK-IV01 Isolation valve Kit TH-PA01 Flue PVC Adaptor (included) TH-PA02 Intake PVC Adaptor TH-CVPVC33 3" PVC Concentric Termination
500 Wald, Irvine, CA 92618 Tel: (949) 770 -7171 Fax: (949) 770-3171 www.takagi.com
T-H2S-DV Pressure Loss
Temperature Rise (°F)
Head Feet
Flow Rate (gpm)
Pressure Loss (psi)
Flow Rate vs. Temperature Rise
Flow Rate (gpm) Set Temperature : 125 °F & lower Set Temperature: 130 °F & Higher
Installation Type Electric Consumption Fuel Gas Consumption Input Energy Factor Inlet Gas Pressure Flow Rate Water Pressure
Temp Settings
Indoor, Direct Vent Only 120 VAC ; Standby: 0.07 A, Operation: 1.27 A, Freeze-Protection: 1.73 A NG LP Min 13,000 BTU/h Min 13,000 BTU/h Max 180,000 BTU/h Max 180,000 BTU/h 0.91 0.91 Min 5.0" W.C. Min 8.0" W.C. Max 10.5" W.C. Max 14.0" W.C. Max 8.0 GPM Pressure Only Relief Valve Required (Min 200,000 BTUs. 150 psi) 15-150 psi 40 psi or above recommended for maximum Flow 100°F, 105°F, 110°F, 115°F, 120°F (Default), 125°F, 135°F, 140°F, 145°F, 150°F, 155°F, 160°F, 165°F, 170°F, 175°F and 185°F (16 options) With TM-RE30 Temperature Remote Controller 100°F to 185°F with 5°F intervals (18 options), 120°F Default Factory Setting With PCB Push Buttons & LED Display
The manufacturer reserves the right to change or discontinue the design, drawing and/or specification of its products without notice at any time.
12-1/2" (316mm)
3-1/2" (90mm)
Ø4" (102mm) Female
Male Ø4" (100.8mm)
3/4" (18.8mm)
2-3/4" (69.1mm) INTAKE
C
25-1/2" (649mm)
UP
®
2-3/4" (71.8mm) EXHAUST
6-5/8" (168.4mm)
1/2" (12.5mm)
29-1/2" (751mm)
6-1/4" (161.5mm)
1-1/4" (29.2mm) COLD
GAS 6" (153.6mm)
120VAC 2-1/4" (58.2mm)
HOT 7-1/4" (182.1mm) 120VAC 8-1/2" (216.3mm)
4-5/8" (116.8mm) GAS
HOT 5-5/8" (142.2mm)
COLD 8-5/8" (220.6mm)
6-1/4" (159.1mm) Condensate Drain Port
10-1/2" (266.8mm) Condensate Drain Port
Dimension Hot/Cold/Gas Connection Clearances
H25.6” x W18.5” x D12.4” Weight: 73 lbs 3/4” NPT Top: 12“ Bottom: 12” Front: 4” Back: 0.5" Sides: 3“
Features
Venting & Combustion
High Efficiency, Condensing Model Low Emission, Low NOx Safety Features: Air-Fuel Ratio (AFR) sensor Exhaust & Water Temperature safety Control Overheat Cutoff Fuse Internal Freeze-Protection System
Secondary Heat Exchanger is made of SS 316L
Built-in temperature, flow rate, and diagnostic display Power Cord included Temperature Remote Controller included (TM-RE30)
Horizontal or Vertical Installation Power Vent Electric Ignition 4" ; 50' Max Length, 5 elbows max 3" ; 25' Max Length, 2 elbows max (90°elbow = 5' equivalent length) Flue 3" or 4" O.D. Schedule 40 PVC/ ABS Venting (PVC Adaptor included, TH-PA01) Category III / IV Stainless Steel Intake 3" or 4" O.D. ABS, PVC, Galvanized Steel, Corrugated Stainless Steel or Category III/IV Stainless Steel
Accessories
TH-PC02 Pipe Cover TH-NT01 Neutralizer Kit TK-IV01 Isolation valve Kit TH-PA01 Flue PVC Adaptor (included) TH-PA02 Intake PVC Adaptor TH-CVPVC33 3" PVC Concentric Termination
500 Wald, Irvine, CA 92618 Tel: (949) 770 -7171 Fax: (949) 770-3171 www.takagi.com
T-H2S-DV Pressure Loss
Temperature Rise (°F)
Head Feet
Flow Rate (gpm)
Pressure Loss (psi)
Flow Rate vs. Temperature Rise
Flow Rate (gpm) Set Temperature : 125 °F & lower Set Temperature: 130 °F & Higher
Installation Type Electric Consumption Fuel Gas Consumption Input Energy Factor Inlet Gas Pressure Flow Rate Water Pressure
Temp Settings
Indoor, Direct Vent Only 120 VAC ; Standby: 0.07 A, Operation: 1.27 A, Freeze-Protection: 1.73 A NG LP Min 13,000 BTU/h Min 13,000 BTU/h Max 180,000 BTU/h Max 180,000 BTU/h 0.91 0.91 Min 5.0" W.C. Min 8.0" W.C. Max 10.5" W.C. Max 14.0" W.C. Max 8.0 GPM Pressure Only Relief Valve Required (Min 200,000 BTUs. 150 psi) 15-150 psi 40 psi or above recommended for maximum Flow 100°F, 105°F, 110°F, 115°F, 120°F (Default), 125°F, 135°F, 140°F, 145°F, 150°F, 155°F, 160°F, 165°F, 170°F, 175°F and 185°F (16 options) With TM-RE30 Temperature Remote Controller 100°F to 185°F with 5°F intervals (18 options), 120°F Default Factory Setting With PCB Push Buttons & LED Display
The manufacturer reserves the right to change or discontinue the design, drawing and/or specification of its products without notice at any time.
