TiVo Series 2 TCD24008A Remote Sensor Replacement
TiVo Series 2 TCD24008A Remote Sensor Replacement
TiVo Series 2 TCD24008A Remote Sensor Replacement Replace the remote sensor in the front of your TiVo.
Written By: Shauna
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 7
TiVo Series 2 TCD24008A Remote Sensor Replacement
INTRODUCTION In case your remote just won't work and you have already tried replacing the batteries, this guide will walk you through removing the front cover and replacing the remote sensor on the inside of the cover.
TOOLS: T9 Torx Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 7
TiVo Series 2 TCD24008A Remote Sensor Replacement
Step 1 — Cover
Unscrew the five 0.31 inch T-9 screws on the back cover.
Slide the cover towards the back until it is no longer under the front cover.
Step 2
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 7
TiVo Series 2 TCD24008A Remote Sensor Replacement
Step 3
Lift the cover up and off the device.
Unplug the ribbon cable from the motherboard. Some force may be required for this step, so be careful not to rip the ribbon cable.
Step 4 — Remote Sensor
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 7
TiVo Series 2 TCD24008A Remote Sensor Replacement
Step 5
Unscrew the two 0.31 inch T-9 screws on the inside of the front cover.
Step 6
Use a spudger to push the three tabs on the inside of the front cover up and forward to release the cover.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 7
TiVo Series 2 TCD24008A Remote Sensor Replacement
Step 7
Pull the front cover down and away from the device to separate it completely. Be careful not to tear the ribbon cable as you are removing the front cover.
Step 8
© iFixit — CC BY-NC-SA
www.iFixit.com
Unscrew the two 0.31 inch T-9 screws on the back of the sensor.
Page 6 of 7
TiVo Series 2 TCD24008A Remote Sensor Replacement
Step 9
Lift the sensor up to remove it.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-23 01:22:30 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 7
TiVo Series 2 TCD24008A Remote Sensor Replacement Replace the remote sensor in the front of your TiVo.
Written By: Shauna
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 1 of 7
TiVo Series 2 TCD24008A Remote Sensor Replacement
INTRODUCTION In case your remote just won't work and you have already tried replacing the batteries, this guide will walk you through removing the front cover and replacing the remote sensor on the inside of the cover.
TOOLS: T9 Torx Screwdriver (1)
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 2 of 7
TiVo Series 2 TCD24008A Remote Sensor Replacement
Step 1 — Cover
Unscrew the five 0.31 inch T-9 screws on the back cover.
Slide the cover towards the back until it is no longer under the front cover.
Step 2
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 3 of 7
TiVo Series 2 TCD24008A Remote Sensor Replacement
Step 3
Lift the cover up and off the device.
Unplug the ribbon cable from the motherboard. Some force may be required for this step, so be careful not to rip the ribbon cable.
Step 4 — Remote Sensor
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 4 of 7
TiVo Series 2 TCD24008A Remote Sensor Replacement
Step 5
Unscrew the two 0.31 inch T-9 screws on the inside of the front cover.
Step 6
Use a spudger to push the three tabs on the inside of the front cover up and forward to release the cover.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 5 of 7
TiVo Series 2 TCD24008A Remote Sensor Replacement
Step 7
Pull the front cover down and away from the device to separate it completely. Be careful not to tear the ribbon cable as you are removing the front cover.
Step 8
© iFixit — CC BY-NC-SA
www.iFixit.com
Unscrew the two 0.31 inch T-9 screws on the back of the sensor.
Page 6 of 7
TiVo Series 2 TCD24008A Remote Sensor Replacement
Step 9
Lift the sensor up to remove it.
To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-06-23 01:22:30 PM.
© iFixit — CC BY-NC-SA
www.iFixit.com
Page 7 of 7
