TiVo Series 2 TCD540080 Power Supply Replacement

Report 2 Downloads 236 Views

Oct 28, 2016 - Replace a broken TiVo power supply. Written By: Svyatoslav Markeyev. TOOLS: T10 Torx Screwdriver (1). TiVo Series 2 TCD540080 Power ...

TiVo Series 2 TCD540080 Power Supply Replacement

TiVo Series 2 TCD540080 Power Supply Replacement Replace a broken TiVo power supply.

Written By: Svyatoslav Markeyev

© iFixit — CC BY-NC-SA

www.iFixit.com

Page 1 of 7

TiVo Series 2 TCD540080 Power Supply Replacement

TOOLS: T10 Torx Screwdriver (1)

© iFixit — CC BY-NC-SA

www.iFixit.com

Page 2 of 7

TiVo Series 2 TCD540080 Power Supply Replacement

Step 1 — Case 

Power down the TiVo and detach the power cable from the rear of the unit.

 Wait 5 minutes for unit to discharge fully before proceeding to next step.

Step 2 

© iFixit — CC BY-NC-SA

www.iFixit.com

Using a Torx screwdriver, remove the five T10 screws from the rear of the case.

Page 3 of 7

TiVo Series 2 TCD540080 Power Supply Replacement

Step 3



Pull the grey outer casing up and back toward yourself.

Step 4 — Power Supply



Carefully remove the ribbon cable from the power supply. Hold the ribbon on both sides and pull up.

© iFixit — CC BY-NC-SA

www.iFixit.com

Page 4 of 7

TiVo Series 2 TCD540080 Power Supply Replacement

Step 5 

Disconnect the hard drive power cable. Firmly grip the white power connector and pull away from the hard drive.

 Do not pull on the power cables when disconnecting power connector.

Step 6 

© iFixit — CC BY-NC-SA

www.iFixit.com

Rotate the device 180 degrees and remove the two T10 screws from the power supply board.

Page 5 of 7

TiVo Series 2 TCD540080 Power Supply Replacement

Step 7



Remove the four plastic standoffs.



Use pliers to squeeze the plastic pieces on the head together. Carefully press down on the standoff and pull up on the power supply.

© iFixit — CC BY-NC-SA

www.iFixit.com

Page 6 of 7

TiVo Series 2 TCD540080 Power Supply Replacement

Step 8



Lift the power supply out of the unit.

 Do not touch any circuit elements or capacitors on the power supply, as they may hold a charge after the unit has been shut off.

To reassemble your device, follow these instructions in reverse order. This document was last generated on 2017-07-13 09:01:22 PM.

© iFixit — CC BY-NC-SA

www.iFixit.com

Page 7 of 7

Recommend Documents
步骤 7. Remove the four plastic standoffs.. Use pliers to squeeze the plastic pieces on the head together. Carefully press down on the standoff and pull up on the power supply.. TiVo Series 2 TCD540080 Power Supply Replacement. © iFixit — CC BY-

TiVo Series 2 TCD540080 Cooling Fan. Replacement. Replace a broken cooling fan on a TiVo. Written By: Svyatoslav Markeyev. TOOLS: T10 Torx Screwdriver ...

Sep 25, 2016 - Disassembling TiVo Series 2 TCD540080 Case. Remove the case on a TiVo Series 2. Written By: Svyatoslav Markeyev. TOOLS: T10 Torx ...

TiVo Series 2 TCD24008A Remote Sensor. Replacement. Replace the remote sensor in the front of your TiVo. Written By: Shauna. INTRODUCTION.

walk you through removing the front cover and replacing the remote sensor on the inside of the cover. HERRAMIENTAS: ... Unscrew the two 0.31 inch T-9 screws on the inside of the front cover.. Paso 6. Use a spudger to push the three tabs on the inside

Oct 28, 2016 - TiVo Series 2 TCD24008A Hard Drive. Replacement. This guide describes how to replace the hard drive. Written By: Talha. INTRODUCTION.

Listed as a General Purpose Power Supply. The 505, 510 and. 515 Series all feature low voltage DC, regulated, filtered power supplies with a built in battery ...

The KTP-24-8 is a compact and durable power supply that is typically used to power up to eight CyberDomes®. It features eight isolated 24 VAC outputs that can power devices requiring 1 amp or less. Each output is equipped with a resettable fuse. The

Oct 28, 2016 - Mitsubishi WD57734 Power Supply. Replacement. Install a new power supply in your Mitsubishi WD-57734 DLP HDTV. Written By: Graham ...